Avermedia AVerVision CP150 User manual

AVerMedia®AVerVision CP150
User Manual
A
V
erMedia
®
Digital Document Camera

P/N 300AP0A7-CPE
Made in Taiwan

EnglishEspañolPortuguês
FCC NOTICE (Class A)
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Federal Communications Commission
Statement
NOTE- This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
tuning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•Consult the dealer or an experienced radio/television technician
for help.
Class A ITE:
Class A ITE is a category of all other ITE which satisfies the
class A ITE limits but not the class B ITE limits. Such
equipment should not be restricted in its sale but the following
warning shall be included in the instructions for use:
Warning - This is a class A product. In a domestic environment
this product may cause radio interference in which case the
user may be required to take adequate measures.
CE Class A (EMC)
This product is herewith confirmed to comply
with the requirements set out in the Council
Directives on the Approximation of the laws of
the Member States relating to Electromagnetic
Compatibility Directive 2004/108/EEC.
Warning - This is a Class A product. In a domestic environment
this product may cause radio interference in which case the
user may be required to take adequate measures to correct this
interference.

DISCLAIMER
No warranty or representation, either expressed or implied, is
made with respect to the contents of this documentation, its
quality, performance, merchantability, or fitness for a particular
purpose. Information presented in this documentation has been
carefully checked for reliability; however, no responsibility is
assumed for inaccuracies. The information contained in this
documentation is subject to change without notice.
In no event will AVerMedia be liable for direct, indirect, special,
incidental, or consequential damages arising out of the use or
inability to use this product or documentation, even if advised of
the possibility of such damages.
TRADEMARKS
AVerVision is registered trademarks of AVerMedia Information,
Inc. IBM PC is a registered trademark of International Business
Machines Corporation. Macintosh is a registered trademark of
Apple Computer, Inc. Microsoft is a registered trademark and
Windows is a trademark of Microsoft Corporation. All other
products or corporate names mentioned in this documentation
are for identification and explanation purposes only, and may
be trademarks or registered trademarks of their respective
owners.
COPYRIGHT
©2008 by AVerMedia INFORMATION, Inc. All rights reserved.
No part of this publication may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated into any
language in any form by any means without the written
permission of AVerMedia Information, Inc.
THE MARK OF CROSSED-OUT WHEELED
BIN INDICATES THAT THIS PRODUCT MUST
NOT BE DISPOSED OF WITH YOUR OTHER
HOUSEHOLD WASTE. INSTEAD, YOU NEED
TO DISPOSE OF THE WASTE EQUIPMENT
BY HANDING IT OVER TO A DESIGNATED
COLLECTION POINT FOR THE RECYCLING
OF WASTE ELECTRICAL AND ELECTRONIC
EQUIPMENT. FOR MORE INFORMATION
ABOUT WHERE TO DROP OFF YOUR
WASTE EQUIPMENT FOR RECYCLING,
PLEASE CONTACT YOUR HOUSEHOLD
WASTE DISPOSAL SERVICE OR THE SHOP
WHERE YOU PURCHASED THE PRODUCT.

EnglishEspañolPortuguês
T
Ta ab bl le e o of f C Co on nt te en nt ts s
Introduction...........................................................1
Package Contents ................................................1
Optional Accessories...........................................2
AVerVision CP150 Parts.......................................3
Technical Specifications......................................4
Making the Connections......................................5
Connecting the Power Adapter................................... 6
Connecting a TV......................................................... 6
Connecting a VGA, Mac Display Monitor or
LCD/DLP Projector ..................................................... 7
Connecting an IBM Compatible PC or
Macintosh Computer .................................................. 7
Installing the Optional Light Box ................................. 8
Connecting to a Microscope ....................................... 9
Setting Up AVerVision CP150..............................9
Camera Head ............................................................. 9
LED Light.................................................................... 9
Flexible Gooseneck and Arm.................................... 10
Infrared Sensor......................................................... 10
Anti-glare Sheet........................................................ 10
Using the Infrared Remote Control ..................11
Touch Button Control Panel..............................13
OSD Navigation Tree..........................................15
Menu Functions..................................................16
Transferring the Captured Images to PC .........20
Troubleshooting .................................................20
Limited Warranty ................................................21

1
EnglishEspañolPortuguês
P
Pa ac ck ka ag ge e C Co on nt te en nt ts s
Anti-glare Sheet
AVerMedia®AVerVision CP150
Driver CD
AVerMedia
®
AVerVisionCP150
UserManual
A
V
erMedia
®
DigitalDocumentCamera
User Manual
Remote Control
(batteries included)
RCA Cable
S-Video Cable
USB Cable
Computer Extension cable
(VGA Cable)
I
In nt tr ro od du uc ct ti io on n
Thank you for purchasing
the AVerMedia®
AVerVision CP150. This
document camera displays
documents, negatives,
transparencies and 3D
objects onto a TV, LCD or
DLP projector making
presentations a snap.
AVerVision CP150 is an
ideal presentation tool for
business, academic,
medical and the scientific
community.
Power Cord
* The power cord will vary
depending on the standard
power outlet of the country
where it is sold.
Power Adapter

2
O Op pt ti io on na al l A Ac cc ce es ss so or ri ie es s
34mm Microscopic Adapter
28mm Microscopic Adapter
Light Box
Bag

3
EnglishEspañolPortuguês
A AV Ve er rV Vi is si io on n C CP P1 15 50 0 P Pa ar rt ts s
The illustrations below identify the parts of AVerVision CP150.
(9)
(8)
(6)
(3)
(4)
(5)
(7)
(1)
(2)
(
10)
(1) Camera head
(2) LED light module
(3) Camera lens
(4) LED switch
(5) IR sensor
(6) Control panel
(7) Right panel
(8) Gooseneck
(9) Rear panel
(10) Left panel
(11) Light box power port
(12) DC 12V port
(13) Antitheft slot
(14) Camera head holder
(15) S-Video output port
(16) Composite video
output port
(17) RGB input port
(18) RGB output port
(19) TV-RGB switch
(20) USB port
(12)
Right Panel
(14)
(11)
(13)
(15)(17)
(16)(18)
Rear Panel
(19)
(20)
Left Panel

4
T
Te ec ch hn ni ic ca al l S Sp pe ec ci if fi ic ca at ti io on ns s
Image
Sensor 1/2" CMOS color image sensor
Pixel Count 3.2 mega pixels
Frame Rate 24 fps (max.)
White Balance Auto / Manual
Exposure Auto / Manual
Image mode Text / Graphics / High Frame
Effect Color / B/W / Negative
Analog RGB output XGA 60 Hz; SVGA 60 Hz; VGA 60 Hz
Image Capture Up to 80 Frames
Optics
Lens F3.0; fl=9.6mm
Focusing Manual
Shooting Area 300mm x 225mm (max.)
Zooming 2X AVERZOOM, 8X Digital Zoom
Power
Power Source 100-240V ~ 4.0-4.2A, 50-60Hz
Consumption 18 Watts (lamp off); 20 Watts (lamp on)
Lighting
Lamp Type LED lamp
Input/Output
RGB Input 15-Pins D-sub (VGA)
RGB Output 15-Pins D-sub (VGA)
S-Video Mini-DIN Jack
Composite Video RCA Jack
USB USB2.0
DC 12V Input Power Jack
Light Box Power Jack (DC 6V Output)
Dimension
Operating 160mm x 170mm x 450mm
Folded 287.4mm x 232.5mm x 61mm
Weight 2.4 kg (about 5.3 lb)

5
EnglishEspañolPortuguês
M
Ma ak ki in ng g t th he e C Co on nn ne ec ct ti io on ns s
The ports on the rear, left and right panel of CP150 enable you to
connect the unit to a computer, graphics display monitor or LCD/DLP
projector, TV or other device. Illustrated below are the ports that are
located at the rear, left and right panel of CP150 with their corresponding
labels.
(2)(3)
(1)
Right Panel
(5) (6)(7) (8)
(4) (9)
Rear & Left Panel
Port Description
(1) Antitheft Slot Attach a Kensington compatible security lock or
antitheft device.
(2) Light Box Plug the optional light box into this port.
(3) DC 12V Input Connect the power adapter into this port.
(4) RGB INPUT Input the signal from a computer or other
sources and pass it through to the RGB Output
port only.
Connect this port to the VGA output port of the
computer.
(5) RGB OUTPUT Output the signal from the camera, RGB input
port, or the captured images from the memory on
a VGA/Mac monitor or LCD/DLP projector.
(6) VIDEO OUTPUT
(RCA/Composite)
Output the signal from the camera or the
captured images from the memory on TV or
Video equipment.
(7) S-VIDEO OUTPUT Output the signal from the camera or the
captured images from the memory on TV or
Video equipment.
(8) USB Use CP150 as a USB Camera or transfer the
captured images from CP150 memory to PC.
(9) TV-RGB switch Switch to output display video either from Video,
S-VIDEO, or RGB output port.

6
C
Co on nn ne ec ct ti in ng g t th he e P Po ow we er r A Ad da ap pt te er r
Connect the power adapter to a standard 100V~240V AC power source.
Power adapter
Power cord
Wall outlet
C
Co on nn ne ec ct ti in ng g a a T TV V
Locate the VIDEO, S-VIDEO or SCART RGB input port of the TV or
Video equipment (i.e., VCR) to record your presentation on a videotape
and connect it to S-VIDEO or VIDEO OUTPUT port of CP150. If you are
not sure, please refer to the user manual of the TV or Video equipment.
For better video quality, we strongly suggest using S-VIDEO
connection.
Make sure the TV/RGB switch is set to TV.
S-Video cable
S-Video to SCART cable
(not supplied)
S-VIDEO
RCA to SCART cable
(not supplied)
RCA cable
VIDEO
SCART
SCART
INPUT
Projector
Television
VCR

7
EnglishEspañolPortuguês
C
Co on nn ne ec ct ti in ng g a a V VG GA A, , M Ma ac c D Di is sp pl la ay y
M
Mo on ni it to or r o or r L LC CD D/ /D DL LP P P Pr ro oj je ec ct to or r
Locate the RGB (VGA) input port of the display device and connect it to
RGB OUTPUT port of CP150. If you are not sure, please refer to the
user manual of the device.
Make sure the TV/RGB switch is set to RGB.
RGB (VGA) cable
(not supplied)
MAC
LCD/DLP projector
LCD monitor
MAC monitor
Monitor Adapter
(not supplied)
CRT monitor
C
Co on nn ne ec ct ti in ng g a an n I IB BM M C Co om mp pa at ti ib bl le e P PC C o or r
M
Ma ac ci in nt to os sh h C Co om mp pu ut te er r
Locate the RGB video output port of the computer or laptop to display
your PC presentation on screen and connect it to RGB INPUT port of
CP150. The video signal from the RGB INPUT port is streamed to RGB
OUTPUT port and displayed on the screen.
Computer extension cable
(VGA cable)
Computer
Laptop
MAC
Monitor Adapter
(not supplied)

8
C
Co on nn ne ec ct ti in ng g a a C Co om mp pu ut te er r v vi ia a U US SB B
C
Co on nn ne ec ct ti io on n
Locate the USB port of the computer or laptop and connect it to USB port
of CP150. This enables you to use CP150 as a USB Camera and to
transfer the captured images from the memory and to computer. Also
see “Transfer Image from AVerVision CP150 to PC”.
USB cable
Computer
Laptop
MAC
I
In ns st ta al ll li in ng g t th he e O Op pt ti io on na al l L Li ig gh ht t B Bo ox x
Connecting an optional light box enables you to view x-rays,
transparencies and negative slides.
Light Bo
x
(optional)
TURN ON
PLUG
IT HERE

9
EnglishEspañolPortuguês
Microscopic
Adapter
Microscope
C
Co on nn ne ec ct ti in ng g t to o a a M Mi ic cr ro os sc co op pe e
Connecting the CP150 to a microscope enables
you to examine microscopic objects on a big
screen without straining your eyes.
S
Se et tt ti in ng g U Up p A AV Ve er rV Vi is si io on n C CP P1 15 50 0
This section provides useful tips on how to adjust the CP150 to meet
your needs.
C
Ca am me er ra a H He ea ad d
The camera head can be turned 90 ° to the left and right. The latch must
be pressed to open and unfold the LED light. You can also manually
adjust the focus from the focus ring to improve the quality of the pictures.
Make sure to unfold the LED light fully.
180°
Latch
Focus
Ring
90° 90°
L
LE ED D L Li ig gh ht t
The LED light provides white light and is best used when presenting in
low light conditions.
Turn On Turn Off

10
F
Fl le ex xi ib bl le e G Go oo os se en ne ec ck k a an nd d A Ar rm m
The flexible gooseneck and arm design allows you to position the
camera head from any angle.
90°
I
In nf fr ra ar re ed d S Se en ns so or r
Aim the remote control at the infrared sensor to operate the unit.
A
An nt ti i- -g gl la ar re e S Sh he ee et t
The anti-glare sheet is a special coated film that helps eliminate any
glare that maybe encountered while displaying very shiny objects or
glossy surfaces such as magazines and pictures. To use, simply place
the anti-glare sheet on top of the shiny document to reduce reflected
light.

11
EnglishEspañolPortuguês
U
Us si in ng g t th he e I In nf fr ra ar re ed d R Re em mo ot te e C Co on nt tr ro ol l
Use the CP150 Remote Control to enhance your presentation by having
the ability to switch between three (3) presentation modes and access
various features. To use the remote control, first insert the batteries (2
“AAA” size batteries are provided) into the battery compartment at the
back of the remote. Use the figure and descriptions below as a reference
for remote control functions.
(1)
(3)
(6)
(7)
(8)
(13)
(12)
(11)
(10)
(9)
(5)
(4)
(2)
Name Function
(1) POWER Turn the unit on/off.
(2) Shuttle Wheel - Turn the shuttle wheel clockwise to zoom in and
counter-clockwise to zoom out the image in Camera
and Playback mode only.
When it reaches the maximum AVERZOOM level of
about 200%, you can still continue to digitally zoom
in the image up to 1600%. Press ENTER to return to
normal view (100%).
- Press the shuttle wheel ▲,▼,◄, &►to pan the
image while in zoom in mode, to make a selection on
16-thumbnail images or move to the next or previous
single full screen preview in Playback mode, or to
make a selection or adjustment on the OSD
main-menu and sub-menu (See Menu Functions for
more details).
(3) ENTER Make a selection in Playback mode and OSD menu.

12
Name Function
(4) Source Switch between Camera, Playback and PC mode.
- Camera mode displays the video signal from the
built-in camera.
- Playback mode displays the captured image from
the built-in memory in 16-thumbnail images. Use
▲,▼,◄, & ►buttons to make a selection and
ENTER to display the selected image in full screen.
To start slide show press MENU and select START
and press ENTER to begin and end. Select
INTERVAL to set the display time interval between
frames in second.
- PC mode displays the video signal from the RGB
INPUT port of CP150.
(5) CAP/DEL - Capture a still image in Camera mode. The captured
image is saved in the built-in memory at 1024 x 768
resolution and can store up to 80 images.
- Remove the selected picture from the built-in
memory permanently in Playback mode.
(6) REVERSE Rotate the image by 180°in Camera mode only.
(7) PROFILE Recall and switch from the 3 saved user setting profile
selections (See MENU Functions – SAVE for more
details).
(8) TIMER Display the OSD timer menu and use ▲or▼buttons to
select SET TIME to set the time value, START to begin
the countdown timer, PAUSE/RESUME to temporarily
halt or continue, and STOP to end.
(9) MENU Pull up and exit the OSD main-menu and sub-menu.
(10) AUTO
IMAGE
Automatically adjust and set the white balance and
exposure setting.
(11) FREEZE Toggle to pause or resume the camera.
(12) EFFECT Convert and display the image in BW, Negative or
Color in Camera and Playback mode only.
(13) PRESENTER Select to turn on/off AVerBox or AVerVisor. Only one
feature can be used at a time.
AVerBox overlays a frame on the presentation screen.
Selecting SHADE changes the opacity of the area
outside the box from 0%, 50% and 100%, COLOR to
change the frame color from red, green and blue, and
RESIZE to change the size of the frame. To resize or
move the frame around the presentation screen, press
the shuttle wheel ▲,▼,◄, & ►.

13
EnglishEspañolPortuguês
Name Function
(13) PRESENTER
AVerVisor covers part of the presentation screen. The
upper part of the presentation screen is slightly
exposed when it is being called each time. To expose
part of the covered area, press the shuttle wheel
▲,▼,◄, & ►. Select SHADE to change the darkness
of the shaded area between 50% or 100%.
T
To ou uc ch h B Bu ut tt to on n C Co on nt tr ro ol l P Pa an ne el l
The touch button control panel located on the top side of the CP150
provides quick access to commonly used functions.
(8)
(9)
(1)
(2)
(3)
(4)
(5)
(7)
(6) (11)
(10)
Function Description
(1) POWER Turn the unit on/off.

14
Function Description
(2) Output LED
Indicator
Indicate the setting of the TV to RGB dip switch to
which the video signal is being sent out.
(3) Shuttle Wheel - Turn the shuttle wheel clockwise to zoom in and
counter-clockwise to zoom out the image in
Camera and Playback mode only.
When it reaches the maximum AVERZOOM level
of about 200%, you can still continue to digitally
zoom in the image up to 1600%. Press ENTER to
return to normal view (100%).
- Press the shuttle wheel ▲,▼,◄, & ►to pan the
image while in zoom in mode, to make a selection
on 16-thumbnail images or move to the next or
previous single full screen preview in Playback
mode, or to make a selection and adjustment on
the OSD main-menu and sub-menu (See Menu
Functions for more details).
(4) ENTER Make a selection in Playback mode and OSD menu.
(5) FREEZE Toggle to pause or resume the camera.
(6) MENU Pull up and exit the OSD main-menu and sub-menu.
(7) Source LED
Indicator
Indicate the source of the video signal or image.
(8) Source Switch between Camera, Playback and PC mode.
- Camera mode displays the video signal from the
built-in camera.
SLIDE SHOW
START
INTERVAL
- Playback mode displays the captured image from
the built-in memory in 16-thumbnail images. Use
▲,▼,◄, & ►buttons to make a selection and
ENTER to display the selected image in full
screen. To start slide show press MENU and
select START and press ENTER to begin and
end. Select INTERVAL to set the display time
interval between frames in second.
- PC mode displays the video signal from the RGB
INPUT port of AVerVision CP150.
(9) AUTO IMAGE Automatically adjust and set the white balance and
exposure setting.
(10) CAP/DEL - Capture a still image in Camera mode. The
captured image is saved in the built-in memory at
1024 x 768 resolution and can store up to 80
images.
- Remove the selected picture from the built-in
memory permanently in Playback mode
(11) EFFECT Convert and display the image in BW, Negative or
Color in Camera and Playback mode only.