Reliable i30 User manual

i30 & i60
Professional Steam Iron
Instruction Manual

USER INSTRUCTIONS i30 & I60
Thank you for purchasing the Reliable™i30 & i60 series iron system. Please
follow the instructions carefully. With proper care and maintenance, your
steamer will provide years of dependable service.
COMPONENTS:
1. Steam button
2. Temperature regulation knob
3. Male electrical plug
4. Quick release of steam hose
5. Iron plate

USER INSTRUCTIONS i30 & i60
1. Remove the steam iron from its packing and make sure all packing parts
have been taken off (including the protective bags). Lay the steam iron
on the supplied pad on the ironing table in steady position.
2. Connect the male plug (3) to the female plug of the steam generator (ref.
nr. 7 - see instruction booklet i700-i702) and the quick release of the
steam hose (4) to the “L” connector (ref. Nr 8 - see instruction booklet
i700-i702).
3. Push the steam switch (ref. Nr. 2 - see instruction booklet i700-i702).
4. Set the temperature regulation knob (2) to “cotton ooo”.
5. Wait for the iron plate to get hot (it takes about 5 minutes).
6. The steam iron is now ready for use.
7. Push the steam button (1) to release steam.
8. Please wait for the steam iron to cool down before storing it away.
CAUTION
-Do not leave the iron on while unattended.
-The iron plate is hot. Please do not touch it during use, or for 15 minutes
afterwards.
TECHNICAL DATA:
Adjustable thermostat: set at 60°C-215°C
Aluminium heater: set at 275°
Safety bimetallic thermostat with manual reset: 800w – 120V-220V

TROUBLESHOOTING:
PROBLEM
EXPLANATION
SOLUTION
Does the
steam iron
leak steam
mixed with
water?
1) While filling the tank you
may have poured too much
water into the tank.
2) The iron plate has to be hot
enough to produce dry steam.
1) The problem will go on until the
excess water is emptied. Keep the
steam button depressed until the
water in the tank is at the correct
level.
2) Please check that the temperature
knob is on the right position: “cotton
°°°”
There is
no steam
coming out
of the
iron?
1) The steam knob (where
supplied) might be closed.
2) The iron switch might be off.
3) The boiler switch might be
off.
4) The water might be used up.
1) Open the steam knob
anticlockwise.
2) After the iron switch comes on,
wait for 4 minutes so that the iron
plate gets hot.
3) After the boiler switch comes on,
wait for 10-20 minutes so the boiler
produces steam.
4) Fill it following the instructions
carefully.
Does the
steam leak
dirty
water?
Some dirty water might have
gone into the boiler with the
water and it is given off from
the iron.
Fill the empty tank with water
(i300/i500), screw the cap tight,
shake it, unscrew the cap and empty
the tank. Repeat the action until the
water is cleaned. We do not
recommend the use of any additive to
pour in the tank. Before ironing again
spray some steam on a cloth until
clean steam comes out.
How to
clean the
boilers
i700-i702
Clean the boiler frequently by opening
the exhaust valve but only when the
boiler has been disconnected from the
electrical outlet – let pressure go down
first.
How to
clean the
boiler
i300-i500
The use of normal tap water is
recommended. In order to clean the
boiler and remove limestone, rinse it
internally (every 15-20 litres of water
used or every month) with tap water.

I30/120V SPARE PARTS LIS
ITEM CODE
VARIANT
ITEM DESCRIPTION
Q.TY
AST114
BLOCKAGE FOR IRONING BOARD ELEMENT
2
CD348/1
SCREW FOR BULB THERMOSTAT
1
CD356
MONO-HOSE MT 2,2 5X10
1
CD356/3
THERMORESCTRICT. CLIP FOR MONOHOSE
MT.1
CD363
PAD
1
CD368/1
SPRING TO HOLD THE HOSE UP
1
CD368/2
CLIP FOR SPRING
1
CD378
HOSE CLAMP 10/12 ONE EAR
1
CD378/1
HOSE CLAMP 9/11 TWO EARS
1
CD490
ANGLE CONNECTION
1
FS200/120
IRON PLATE 120V
1
FS003
ADJUSTABLE THERMOSTAT
1
FS004
THERMOSTAT 271 WITH MANUAL RESET
1
FS005
CORK HANDLE
1
FS006
BRACKET
1
FS007
CAP
1
FS009
WIRING
1
FS011
INSERT FOR HANDLE
1
FS012
SCREW M4x22 FOR THERMOSTAT FIXING
1
FS014
SCREW FOR BACKHANDLE
3
FS015
SCREW FOR MICRO CLOSING
2
FS016
SCREW FOR MICRO-CASE
1
FS017
SCREW FOR HANDLE FIXING M5x10
2
FS018
SCREW FOR TERMINAL BLOCK FIXING
3
FS019
HANDLE COVER
1
FS020
BACKHANDLE
1
FS021
BUTTON-CASE
1
FS022
BUTTON-CASE COVER
1
FS023
UPPER BUTTON
1
FS024
LOWER BUTTON
1
FS025
PLATE FOR BRACKET COVER
1
FS026
CORD BLOCKAGE
1
FS027
FRONT HANDLE HOLDER
1
FS028
BACK HANDLE HOLDER
1
FS030
SCREW CAP
2
FS031
BRASS WASHER-SPACER
2
FS032
BRASS MALE FEMALE SPACER
2
FS033
MICRON
1
FS035
SCREW FOR HANDLE
4
FS036
VAR. 120V
BLACK BACHELITE PRINTED KNOB
1
FS038
LOWER HANDLE WASHER FOR SCREW
2
FS039
LOWER HANDLE WASHER FOR KNOB
1
FS041
FAIRLEAD FOR CABLE
1
GV026/9
QUICK RELEASE
1

GV028/38
MALE PLUG
1
GV028/39
REMOVABLE COVER
1
GV028/40
CABLE PRESS FOR MALE SOCKET
1
RIC003
4 POLE TERMINAL BOARD
1

i30/120V PARTS DRAWING

i30/220V PARTS LIST
ITEM
ITEM DESCRIPTION
Q.TY
AST114
BLOCKAGE FOR IRONING BOARD HEATING ELEMENT
2
CD348/1
SCREW FOR BULB THERMOSTAT
1
CD356
MONO-HOSE MT 2,2 5X10
1
CD356/3
THERMORESCTRICTING CLIP FOR MONO-HOSE
MT.1
CD363
PAD
1
CD368/1
SPRING TO HOLD THE HOSE UP
1
CD368/2
CLIP FOR SPRING
1
CD378
HOSE CLAMP 10/12 ONE EAR
1
CD378/1
HOSE CLAMP 9/11 TWO EARS
1
CD490
ANGLE CONNECTION
1
FS200
IRON PLATE 220V
1
FS003
ADJUSTABLE THERMOSTAT
1
FS004
THERMOSTAT 271 WITH MANUAL RESET
1
FS005
CORK HANDLE
1
FS006
BRACKET
1
FS007
CAP
1
FS009
WIRING
1
FS011
INSERT FOR HANDLE
1
FS012
SCREW M4x22 FOR THERMOSTAT FIXING
1
FS014
SCREW FOR BACKHANDLE
3
FS015
SCREW FOR MICRO CLOSING
2
FS016
SCREW FOR MICRO-CASE
1
FS017
SCREW FOR HANDLE FIXING M5x10
2
FS018
SCREW FOR TERMINAL BLOCK FIXING
3
FS019
HANDLE COVER
1
FS020
BACKHANDLE
1
FS021
BUTTON-CASE
1
FS022
BUTTON-CASE COVER
1
FS023
UPPER BUTTON
1
FS024
LOWER BUTTON
1
FS025
PLATE FOR BRACKET COVER
1
FS026
CORD BLOCKAGE
1
FS027
FRONT HANDLE HOLDER
1
FS028
BACK HANDLE HOLDER
1
FS030
SCREW CAP
2
FS031
BRASS WASHER-SPACER
2
FS032
BRASS MALE FEMALE SPACER
2
FS033
MICRON
1
FS035
SCREW FOR HANDLE
4
FS036
BLACK BACHELITE SILKSCREEN PRINTED KNOB
1
FS038
LOWER HANDLE WASHER FOR SCREW
2
FS039
LOWER HANDLE WASHER FOR KNOB
1
FS041
FAIRLEAD FOR CABLE
1
GV026/9
QUICK RELEASE
1

GV028/38
MALE PLUG
1
GV028/39
REMOVABLE COVER
1
GV028/40
CAVBLE PRESS FOR MALE SOCKET
1
RIC003
4 POLE TERMINAL BOARD
1

i30/220V PARTS DRAWING

I60/120V PARTS LIST
ITEM
VAR.
DESCRIPTION
Q.TY
AST114
BLOCKAGE FOR IRONING BOARD ELEMENT
2
CD348/1
SCREW FOR BULB THERMOSTAT
1
CD356
MONO-HOSE MT 2,2 5X10
1
CD363
PAD
1
CD368/1
SPRING TO HOLD THE HOSE UP
1
CD368/2
CLIP FOR SPRING
1
CD378
HOSE CLAMP 10/12 ONE EAR
1
CD378/1
HOSE CLAMP 9/11 TWO EARS
1
CD490
ANGLE CONNECTION
1
FS200/120
NEW IRON PLATE 120V
1
FS003
ADJUSTABLE THERMOSTAT
1
FS004
THERMOSTAT 271 WITH MANUAL RESET
1
FS005
CORK HANDLE
1
FS006
BRACKET
1
FS007
CAP
1
FS009
WIRING
1
FS011
INSERT FOR HANDLE
1
FS012
SCREW M4x22 FOR THERMOSTAT FIXING
1
FS014
SCREW FOR BACKHANDLE
3
FS015
SCREW FOR MICRO CLOSING
2
FS016
SCREW FOR MICRO-CASE
1
FS017
SCREW FOR HANDLE FIXING M5x10
2
FS018
SCREW FOR TERMINAL BLOCK FIXING
3
FS019
HANDLE COVER
1
FS020
Reliable
BACKHANDLE
1
FS021
BUTTON-CASE
1
FS022
BUTTON-CASE COVER
1
FS023
UPPER BUTTON
1
FS024
LOWER BUTTON
1
FS025
PLATE FOR BRACKET COVER
1
FS026
CORD BLOCKAGE
1
FS027
FRONT HANDLE HOLDER
1
FS028
BACK HANDLE HOLDER
1
FS030
SCREW CAP
2
FS031
BRASS WASHER-SPACER
2
FS032/1
BRASS MALE FEMALE SPACER
2
FS033
MICRON
1
FS035
SCREW FOR HANDLE
4
FS036
120V
BLACK BACHELITE PRINTED KNOB
1
FS038
LOWER HANDLE WASHER FOR SCREW
2
FS039
LOWER HANDLE WASHER FOR KNOB
1
FS041
FAIRLEAD FOR CABLE
1
FS042
DIE CAST COUNTERBALANCE
1
GV026/9
QUICK RELEASE
1

ITEM
VAR.
DESCRIPTION
Q.TY
GV028/38
MALE PLUG
1
GV028/39
REMOVABLE COVER
1
GV028/40
CABLE PRESS FOR MALE SOCKET
1
RIC003
4 POLE TERMINAL BOARD
1

i60/120V PARTS DRAWING

I60/220V PARTS LIST
ITEM
VAR.
DESCRIPTION
Q.TY
AST114
BLOCKAGE FOR IRONING BOARD ELEMENT
2
CD348/1
SCREW FOR BULB THERMOSTAT
1
CD356
MONO-HOSE MT 2,2 5X10
1
CD363
PAD
1
CD368/1
SPRING TO HOLD THE HOSE UP
1
CD368/2
CLIP FOR SPRING
1
CD378
HOSE CLAMP 10/12 ONE EAR
1
CD378/1
HOSE CLAMP 9/11 TWO EARS
1
CD490
ANGLE CONNECTION
1
FS200
NEW IRON PLATE
1
FS003
ADJUSTABLE THERMOSTAT
1
FS004
THERMOSTAT 271 WITH MANUAL RESET
1
FS005
CORK HANDLE
1
FS006
BRACKET
1
FS007
CAP
1
FS009
WIRING
1
FS011
INSERT FOR HANDLE
1
FS012
SCREW M4x22 FOR THERMOSTAT FIXING
1
FS014
SCREW FOR BACKHANDLE
3
FS015
SCREW FOR MICRO CLOSING
2
FS016
SCREW FOR MICRO-CASE
1
FS017
SCREW FOR HANDLE FIXING M5x10
2
FS018
SCREW FOR TERMINAL BLOCK FIXING
3
FS019
HANDLE COVER
1
FS020
RELIABLE
BACKHANDLE
1
FS021
BUTTON-CASE
1
FS022
BUTTON-CASE COVER
1
FS023
UPPER BUTTON
1
FS024
LOWER BUTTON
1
FS025
PLATE FOR BRACKET COVER
1
FS026
CORD BLOCKAGE
1
FS027
FRONT HANDLE HOLDER
1
FS028
BACK HANDLE HOLDER
1
FS030
SCREW CAP
2
FS031
BRASS WASHER-SPACER
2
FS032/1
BRASS MALE FEMALE SPACER
2
FS033
MICRON
1
FS035
SCREW FOR HANDLE
4
FS036
BLACK BACHELITE PRINTED KNOB
1
FS038
LOWER HANDLE WASHER FOR SCREW
2
FS039
LOWER HANDLE WASHER FOR KNOB
1
FS041
FAIRLEAD FOR CABLE
1
FS042
DIE CAST COUNTERBALANCE
1
GV026/9
QUICK RELEASE
1

ITEM
VAR.
DESCRIPTION
Q.TY
GV028/38
MALE PLUG
1
GV028/39
REMOVABLE COVER
1
GV028/40
CABLE PRESS FOR MALE SOCKET
1
RIC003
4 POLE TERMINAL BOARD
1

i60/220V PARTS DRAWING

Reliable Corporation
5-100 Wingold Ave.
Toronto, ON M6B 4K7
Canada
P 416 785 0200
F 416 785 7038
TF 800 268 1649
www.reliablecorporation.com