REMACO TECHNOLOGIES PLT-418C User manual

Model Kept Position Height Maximum Extended Height
PLT-418C 86.3cm 410cm
Warning Caution with main supply and live wires. Install with qualified technician or trained
personnel.
Installation Guide (PLT-418C)
CWebsite: www.remacotech.com
COPYRIGHTS 1998 REMACO TECHNOLOGIES PTE LTD
PLT
V: 2.0
*Depending on the lift drop height
31.4cm
463cm
86.3cm
60.1cm
53.4cm
79.7cm
53.4cm
79.7cm
Top Frame
C-Hook
Bracket
Scissor Bar
Stainless Steel
Wire
(4 nos)
Motor
Bottom Frame
Perforated Hole
Ceiling Closure
Threaded Rod
Back
Front
Types of Installation Mounts
Mount Directly To Concrete Ceiling
Front View
LCD/Laser Projector
Front View
Suspended From Concret Ceiling
with Threaded Rod
←Threaded Rod (Optional)→
Concrete
Concrete
LCD/Laser Projector
Load Capacity
70kg

Drill Dia. 10mm holes to a depth of 55mm..
(Note: Do not drill too deep)
10mm Drill
Power Drill
55
Step 1
Insert M8 anchor into the hole.
Use pin punch to expand the anchor.
Hammer
M8 Anchor Bolt
Step 2
Steps for Installation
LCD/Laser Projector
Concrete
Ceiling Enclosure
Threaded Rod
Bottom Frame
Stainless Steel
Wire
(4nos)
Top Frame
C-Hook Bracket
78.7 x 4.1 x 3cm
M8 Anchor
60.1cm (Ceiling Enclosure, Outer)
53.2cm (Ceiling Enclosure, Inner)
53.4cm
60.1cm (Hollow Ceiling Frame, Outer)
False Ceiling
(Plaster Ceiling)
54.8cm (Ceiling Cut Hole Size)
Hollow Ceiling
Frame
60 x 87cm
False Ceiling
(Plaster Ceiling)
Hollow Ceiling
Frame
60 x 87cm

29.9 cm29.9 cm
22.2 cm 22.3 cm 22.2 cm
49.8 cm
60.1 cm
86.3 cm
To cut out plaster ceiling hole size and allow hollow
ceiling frame can insert nicely.
Hollow Ceiling
Frame
To Cut Out Plaster Ceiling
Hole (& insert Ceiling Frame
into this hole)
Plaster Ceiling
(False Ceiling)
Screws to hold Hollow
Ceiling Frame onto
Plaster Ceiling
54.8cm
81.8cm
Step 3 Step 4
1. Lift up
2. Slip in
Step 5: Remote Operation
Move Upward Stop Movement Move Downward Move to third limit
(for maintenance purposes)
Press and hold (STOP) for 2 sec.
Up Stop Down Stop for
2sec.

Pairing RF Remote to Electronic Motor
Setting of Upper and Lower Limit
P2 x 1
Switch (OFF) first then
Switch (ON)
Motor
beeps
press setting button (P2)
one time
within 5 sec.
press (DOWN) button
one time
Direction 1
press (UP) button
one time
UP x 1
DOWN x 1
OFF x 1
ON x 1
P2 x 1
press setting button (P2)
one time
within 5 sec.
Motor roll
up and down
Motor roll
up and down
Motor
beeps
Direction 2
(Change Direction)
Motor
beeps
P2 x 1
press setting button (P2)
one time
UP x 1
press (UP) button
one time
P2 x 1
press setting button (P2)
one time
within 5 sec.
UP x 1
press (UP) button
again to adjust
the upper limit
Motor
beeps
Motor roll
up and down
Motor roll
up and down
Motor roll
up and down
STOP (5sec)
press and hold
(STOP) button
for 5sec
prepare to press
(STOP)
when reaching desired
limit position
DOWN x 1
press (DOWN) button
again to adjust
the lower limit
STOP (5sec)
press and hold
(STOP) button
for 5sec
prepare to press
(STOP)
when reaching desired
limit position
Motor roll
up and down
Motor roll
up and down
Motor Beeps.
Limit setting
was successful.
Motor Beeps.
Limit setting
was successful.
Motor
beeps
Motor roll
up and down
Motor roll
up and down
STOP x 1
press (STOP) button
one time
STOP x 1
press (STOP) button
one time
Successful
Step 6: Pairing, Limit Position Settings, and Deleting

Setting of Third Limit (Below Lower Limit for Maintenance)
P2 x 1
press setting button (P2)
one time
Motor roll
up and down
Down
limit position
DOWN x 1
press (DOWN) button
one time
Motor roll
up and down
DOWN x 1
press (DOWN) button
one time
Motor roll
up and down
press (DOWN) button
one at a time until
reaching desired limit.
Motor rolling
downward in steps
P2 x 1
press setting button (P2)
one time
within 5 sec.
Motor roll
up and down
Motor
beeps
STOP x 1
press (STOP) button
one time
Motor roll
up and down
STOP (5sec)
press and hold
(STOP) button
for 5sec
Motor roll
up and down
Motor
beeps
Delete the Limits
P2 x 1
press setting button (P2)
one time
DOWN x 1
press (DOWN) button
one time
P2 x 1
press setting button (P2)
one time
within 5 sec.
Motor
beeps
Motor roll
up and down
Motor roll
up and down
Successful
Successful
Delete Memory of RF Remote Pairing
P2 x 1
press setting button (P2)
one time
STOP x 1
press (STOP) button
one time
P2 x 1
press setting button (P2)
one time
within 5 sec.
Motor
beeps
Motor roll
up and down
Motor roll
up and down
Successful
(Delete all pairing memory)
Motor
beeps
Motor
beeps

Fine Tuning of Upper/Lower Limit
press (DOWN) button
one time until
reaching desired
lower limit postion
press (UP) button
one time until
reaching desired
upper limit postion
UP x 1
DOWN x 1
Motor roll
up and down
Motor move
in steps
Motor move
in steps
press (UP) and (DOWN)
button together for
3 sec.
press STOP button
and hold for 3sec.
STOP x 1
STOP x 1
press STOP button
and hold for 3sec.
Appendix (Setting not required, use when needed)
Adding 2nd RF Remote
P2 x 1
press setting button (P2)
of RF Remote (RF 1)
one time
Successful
P2 x 1
press setting button (P2)
of RF Remote (RF 1)
one time within 5 sec.
Motor roll
up and down
Motor roll
up and down
P2 x 1
press setting button (P2)
of RF Remote (RF 2)
one time within 5 sec.
RF 1 RF 2 RF 1
Motor
beeps
(UP+DOWN) x 1 Motor move
in steps
Motor move
in steps
Successful
Successful
Motor roll
up and down
Motor
beeps
Delete Third Limit Position
P2 x 1
press setting button (P2)
of RF Remote (RF 1)
one time
Successful
STOP x 1
press STOP button
and hold for 3sec.
Motor roll
up and down
Motor roll
up and down
STOP x 1
press STOP button
and hold for 3sec.
Motor roll
up and down
Motor
beeps