Remington F9200AU User manual

2 YEAR WARRANTY
To register your product go to
www.remington-products.com.au
www.remington.co.nz
F9200AU
USE & CARE
MANUAL
PLEASE READ
PRIOR TO USE
PERFORMANCE SHAVE
POWER SHAVER

2
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic precautions should
always be observed, including the following.
READ ALL INSTRUCTIONS BEFORE USING
For additional protection, the installation of a residual
current device (rcd) having a rated residual operating
current not exceeding 30 mA is advisable in the electrical
circuit supplying the bathroom. Ask your installer for advice.
WARNING: TO REDUCE THE RISK OF BURNS,
ELECTROCUTION AND FIRE OR INJURY TO PERSONS
DANGER: As with most electrical appliances, electrical
parts are electrically live even when the switch is off.
• The appliance should never be left unattended when plugged
into a power outlet, except when charging the appliance.
• This appliance should not be used by children or other persons
with reduced physical, sensory or mental capabilities or lack
of experience and knowledge unless they have been given
supervision or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
• This appliance is not a toy. Children shall be supervised to
ensure they do not play with the appliance. Cleaning and use
maintenance shall not be made by children without supervision.
• Keep the appliance and the power cord away from edge of
tables or countertops and out of reach of children and persons
with reduced physical, sensory or mental capabilities.
• Never operate this appliance if it has a damaged cord or plug,
if it is not working correctly, if it has been dropped or damaged,
or dropped into water. If the supply cord or plug of the appliance
is damaged it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard. It
cannot be repaired. Keep the cord away from heated surfaces.
• Charge, use and store the product at a temperature between
0°C and 32°C.

3
• Do not use outdoors or where aerosol (spray) products are
being used, or where oxygen is being administered.
• Do not use this appliance with damaged or broken tracks, foils
or cutters, as injury may occur.
• For use on facial hair only. Not intended for shaving the hair on
your head.
• Do not plug or unplug the appliance with wet hands.
• For household use only.
• Do not place or store the appliance or charging adaptor where it
can fall or be knocked into a sink or bath.
• Do not place in or drop into water or any other liquid for
extended periods of time.
• If an appliance falls into water, “unplug it” immediately. Do not
reach into the water.
• Unplug the charging adaptor from the electrical outlet
immediately after fully charging.
• Unplug and switch off this appliance before cleaning it.
• Use this appliance only for its intended use as described in this
manual.
• Do not use attachments not recommended by Remington.
• Never drop or insert any object into any opening of this
appliance.
• Always store the charging adaptor in a moisture-free location.
• Do not use on people who are asleep.
• Do not use an extension cord or a voltage converter with this
appliance.
• Do not wrap the cord around the appliance.
Remington strongly recommends that an approved Safety Switch
(Residual current device) be installed to protect all bathroom power
outlets. Ask an electrical contractor for advice.
SAVE THESE INSTRUCTIONS

4
F9200AU PERFORMANCE SHAVE POWER SHAVER
USE & CARE INSTRUCTION MANUAL
Thank you for purchasing your new Remington®Performance Shave Power Shaver.
Inside this manual you will find tips on using and caring for your shaver.
KEY PARTS
1. Power Button
2. Shaver Head
3. Pop Up / Intercept Trimmer
4. Inner Foil
5. Intercept Trimmer
6. Outer Foil
7. Head Assembly Release Tabs
8. Hair Pocket (not shown)
9. LED Display (battery reserve,
turbo function, travel lock)
Also Includes:
• Charging Stand
• Head Guard
• Storage Pouch
• Power Adaptor
• Cleaning Brush
1
2
3
5
4
9
8
7
6

5
ABOUT YOUR SHAVER
F9200AU SPECIFICATIONS
Power System Lithium Rechargeable
Full Charge Time 2 Hours
Cordless Shave Time Up to 2 Hours
Quick Charge Yes
Indicators Charging/Battery Reserve/Turbo/
Travel Lock
Voltage Type Worldwide
Replacement Foils & Cutters SPF-F9200AU
Washable Head Yes
Travel Lock Yes
TRAVEL LOCK FEATURE
Your F9200AU shaver is equipped with a Travel Lock feature, intended to prevent the
shaver from turning on and discharging accidently while packed in luggage.
TO SET THE TRAVEL LOCK
1. Press and hold the power button for 3 seconds. The shaver will turn on, then will
shut off after the 3 seconds. The LED display will flash five times to indicate the
lock is set.
2. While the travel lock is set, if the power button is pressed, the LED display will
flash the travel lock light.
TO UNLOCK THE TRAVEL LOCK
1. Press and hold the power button for 3 seconds. The LED display will flash the
travel lock light three times while the button is being held and then the shaver will
turn on.
QUICK CHARGE
The quick charge function allows you to place the shaver on charge for 5 minutes
providing up to 5 minutes of use - approximately one shave. If the turbo function is
activated then the usage time will be reduced to up to 3 minutes.

6
CHARGING
1. Ensure the shaver is turned off and place the head guard on.
2. Insert the AC adaptor securely into the charging stand.
3. Place the shaver into the charging stand securely for charging.
4. Plug the adaptor into the wall outlet.
5. This unit can also be charged by plugging the adaptor to the shaver directly.
6. Before using your shaver for the first time, charge it for 2 hours.
NOTE: This product must only be used with the power adaptor provided
with the product.
LED DISPLAY
DURING RECHARGING
The indicator lights will flash on the LED display, and will light up one by one from the
bottom to indicate the power reserve.
AFTER FULL CHARGE
The indicator lights will flash and then turn off.
WHILE SHAVING
The indicator lights will go out one by one as the power reserve decreases.

HOW TO USE
1. Remove the head guard.
2. Press the power button to turn on.
3. Pressing the power button again during operation will turn the turbo function on.
turbo function on.
4. Press the power button to turn off.
TURBO FUNCTION
Press the power button once to activate standard shave speed. This speed is intended
for daily shaving or finer beards. Press the power button again to activate the turbo
function, this increases the motor RPM to provide a more powerful shave. The turbo
function is intended for shaving a two or three day beard growth and to provide
additional power to thickness areas of the beard.
HEAD LOCK
• The head moves freely by sliding the head lock button downward on the back of
the shaver.
• The head can be locked at any angle by sliding the head lock button upward.
POP UP / INTERCEPT TRIMMER
There are 3 ways to use the pop up / intercept trimmer (blue trimmer in front of the foils)
• The trimmer is set to the following position according to the purpose.
• The position of the trimmer can be changed even when the power is set to ON.
7
TURBO
Light
Beard
Set the trimmer to the
middle position
Moustache
Push trimmer down
Detail Trimming
Pull out the trimmer
upwards

8
SHAVING
1. Press power button to turn on.
2. Shave face and neck using short, circular strokes.
3. Shaver can be used wet or dry.
SHAVING TIPS (WET)
NOTE: In order to ensure optimal performance, thoroughly rinse the
shaver head under water during and after shaving.
4. Apply water to face and neck area.
5. Apply shave gel or foam to applicable shaving area.
6. Rinse shaver head under water.
7. Shave face and neck using short, circular strokes.
8. Throughout the shave, regularly rinse the shaver head under water to avoid
residue build up.
9. When finished shaving, rinse face.
10. Thoroughly rinse shaver head of all gel or foam.
11. Follow shaver cleaning and care instructions located on page 11
SHAVING TIPS (DRY)
• Ensure your skin is free of oils.
• Wait at least 15 minutes after getting up before shaving, to ensure your face is
free of puffiness that may be present from sleeping.
• Always hold the shaver at a right angle to the skin so that the screens are touching
the skin with equal pressure.
• Stretch skin with the free hand so hairs stand upright, making it easier for them to
enter the cutting chamber.
• Use moderate to slow, circular stroking movement.
• The use of short, circular motions in stubborn areas may obtain a closer shave,
especially along the neck and chin line.
• Do not press hard against the skin to avoid skin irritation and/or damage to the
shaver head.
We recommend that you use your new shaver daily for up to four weeks
to allow time for your hair and skin to become accustomed to the new
shaving system

Article Price each
AUD
Price each
NZD Qty Amount
$
Face Saver: Pre-shave Powder Stick
SP4 SP5 $11.95 AUD $14.95 NZD $
$ $ $ $
Sub Total
Postage &
handling
TOTAL
7.50
R
Shaver Saver: Aerosol Spray Cleaner
eplacement
Shaving Foil & Cutters for F9200AU
SPF-F9200AU $
$11.95 AUD $14.95 NZD
39.95 AUD $44.95 NZD
Remington is a Registered Trademark of Spectrum Brands, Inc., or one of its subsidiaries.

CLEANING & MAINTENANCE
NOTE: When cleaning your shaver, make sure the shaver is turned off and
disconnected from the power cord.
CAUTION:
• To clean the external surfaces of the shaver, use a damp cloth. Do not use strong
detergents or other chemicals.
• To dry, wipe the surface of the shaver with a dry towel. Do not use a hair dryer or
heater to dry the shaver.
CLEANING YOUR SHAVER
We recommend following these steps after each use.
1. Remove the foil assembly by gripping the head assembly release tabs on both
sides of the head and lifting the foil assembly upwards to remove from the hair
pocket.
2. Tap out excess hair shavings.
3. Rinse the head of the assembly under warm running water.
4. Dry the head assembly thoroughly
5. Replace the head assembly by placing the assembly on top of the hair pocket,
press down and click into place.
NOTE: Lubricate foils and trimmers with lubricating oil every six months
11
1.
4.
3.
5.

BATTERY DISPOSAL
NOTE: The battery is not intended to be removed or replaced under normal use.
The only time the battery should be removed or the unit opened or disassembled,
is at the end of the product’s useful life before it is discarded.
BATTERY DISPOSAL
The F9200AU shaver contains a lithium-ion battery. Once the trimmer has reached
the end of its life, to ensure proper disposal of the product, please take the appliance
to a recycling centre, where the internal rechargeable battery should be removed by a
professional and recycled separately.
For more information about recycling of electrical and battery operated appliances,
please contact your local council office or your household waste disposal service.
CAUTION: Do not put in the fire or mutilate your batteries when disposing as
they may burst and release toxic materials. Do not short circuit as it may cause
burns.
12
REPLACING THE SHAVER FOIL & CUTTERS
It is very important to replace your head and cutters when necessary to ensure a close,
comfortable shave without irritation. We recommend they be replaced every 6 months.
Here are some signs of head and cutter wear, indicating that replacement is needed:
• Irritation: As the heads get excessively worn you may experience some skin
irritation. This would be especially noticeable when you apply moisturizing lotion.
• Pulling: When the cutters wear you may feel a sense of pulling and a loss of
closeness when you shave. This is an indication that it is time to replace your
heads and cutters.
Replacement heads & cutters may be obtained from your local retailer, or directly from
Remington®. Simply fill out the enclosed accessory order form or alternatively your order
can be processed over the phone via the Remington®Service Hotline - refer to page 10.
THIS PRODUCT IS NOT SUITABLE TO USE IN THE BATH OR SHOWER.
This product conforms to radio frequency interference requirements
Any product purchased and used commercially carries a limited 90 Day Warranty.

13
1.
3.
2.
4.
HOW TO REPLACE THE SHAVER FOIL & CUTTERS
NOTE: Before replacing the shaver foil and cutters, be sure to turn off the shaver.
1. Remove the foil assembly by gripping the head assembly release tabs on both
sides of the head and lifting the foil assembly upwards to remove from the hair
pocket.
2. Grasp the cutters between the thumb and the forefinger and pull upward.
3. Snap each of the new cutter assemblies into the top of the drive shaft. Do
not push on the ends of the cutters as this may bend them and reduce their
effectiveness.
4. Insert the new foil assembly on top of the hair pocket until it snaps into place.
Vibrator
Vibrator

14
MONEY BACK OFFER – AUSTRALIA / NEW ZEALAND ONLY
If within 60 days you are not fully satisfied with your Remington
®shaver, just return the shaver with this completed coupon
and a copy of your Australian/New Zealand purchase receipt to Remington®. In return, we will send you a cheque for the
full purchase price of the shaver. Please allow 6-8 weeks for your cheque to arrive.
Name: Address: City:
State: Postcode:
Contact No: Area Code: Ph: Product Model number: Is this the first Remington shaver you have owned/purchased? Yes No What is the reason you are returning this product?

Spectrum Brands Australia Pty Ltd and Spectrum Brands New Zealand Limited
WARRANTY AGAINST DEFECTS
In this warranty:
Australian Consumer Law means the Australian consumer law set out in Schedule 2 to the
Competition and Consumer Act 2010;
CGA means the New Zealand Consumer Guarantees Act 1993;
Goods means the product or equipment which was accompanied by this warranty and purchased
in Australia or New Zealand, as the case may be;
Manufacturer, We or us means:
1. for Goods purchased in Australia, Spectrum Brands Australia Pty Ltd
ACN, 007 070 573; or
2. for Goods purchased in New Zealand, Spectrum Brands New Zealand Limited,as the case
may be, contact details as set out at the end of this warranty;
Supplier means the authorised distributor or retailer of the Goods that sold you the Goods
in Australia or in New Zealand; and
You means you, the original end-user purchaser of the Goods.
1. Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law, or the CGA. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
2. The benefits provided by this Warranty are in addition to all other rights and remedies in
respect of the Goods which the consumer has under either the Australian Consumer Law or
the CGA. The original purchaser of the Goods is provided with the following Warranty subject
to the Warranty Conditions:
3. We warrant the Goods for all parts defective in workmanship or materials for the period of two
(2) years from the date of purchase (Warranty Period). If the Goods prove defective within
the Warranty Period by reason of improper workmanship or material, we may, at our own
discretion, repair or replace the Goods without charge.
Warranty Conditions
4. The Goods must be used in accordance with the manufacturer’s instructions. This Warranty
does not apply should the defect in or failure of the Goods be attributable to misuse, abuse,
accident or non-observance of manufacturer’s instructions on the part of the user. As far as
the law permits, the manufacturer does not accept liability for any direct or consequential
loss, damage or other expense caused by or arising out of any failure to use the Goods in
accordance with the manufacturer’s instructions.
5. Exhaustible components (such as shaver heads, cutters and foils) of the Goods are included
under this Warranty only where there is a defect in workmanship or materials used.
6. The warranty granted under clause 3 is limited to repair or replacement only.
7. Any parts of the Goods replaced during repairs or any product replaced remain the property
of the manufacturer. In the event of the Goods being replaced during the Warranty Period, the
warranty on the replacement Goods will expire on the same date as for the Warranty Period on
the original Goods which are replaced.
15

8. In order to claim under the warranty granted under clause 3 you must:
(a) Retain this warranty with your receipt/proof of purchase; and
(b) Return the Goods to us at the relevant address below or to the Supplier by prepaid freight
within the Warranty Period accompanied with (i) the legible and unmodified original proof of
purchase, which clearly indicates the name and address of the
Supplier, the date and place of purchase, the product name or other product serial
number and (ii) this warranty.
9. This warranty is immediately void if:
(a) Any serial number or appliance plate is removed or defaced;
(b) The Goods have been serviced or otherwise repaired by a person not authorised to
do so by us or where non approved replaced parts are used.
10.The Goods are designed for domestic use only. A limited 90-day Warranty applies to any
industrial or commercial use of the Goods. The Goods must be connected to the electrical
voltage requirements as specified in the ratings label located on the Goods.
11.This warranty does not cover the cost of claiming under the warranty or transport of the
Goods to and from the Supplier or us.
12.This warranty is only valid and enforceable in Australia against Spectrum Brands
Australia Pty Ltd and in New Zealand against Spectrum Brands New Zealand Limited.
Contact us or the Supplier for further details.
Spectrum Brands Australia Pty Ltd
Locked Bag 3004
Braeside, VIC 3195
AUSTRALIA
Customer service in Australia: 1800 623 118
E-mail: [e-mail]
Website: www.remington-products.com.au
Spectrum Brands New Zealand Limited
PO Box 9817
Newmarket, Auckland 1149
NEW ZEALAND
Customer service in New Zealand: 0800 736 776
E-mail: [e-mail]
Website: www.remington.co.nz
REMINGTON SERVICE HOTLINE
Australia 1800 623 118 (toll free)
New Zealand 0800 736 776 (toll free)
® Registered Trademark of Spectrum Brands, Inc., or one of its subsidiaries
Made in China to the specifications of Spectrum Brands, Inc.
© 2016 Spectrum Brands, Inc.
REV: 07/16
PART NO: T22-0004308
16