Remington R6150AU User manual

1
2 YEAR WARRANTY R6150AU & R8150AU
USE & CARE
MANUAL
PLEASE READ
PRIOR TO USE
TITANIUM
SHAVER

2
IMPORTANT SAFETY INSTRUCTIONS
When using an electric shaver, basic safety precautions
should always be observed, including the following.
Read all instructions before using this shaver.
KEEP POWER ADAPTOR AWAY FROM WATER
WARNING – TO REDUCE THE RISK OF BURNS, FIRE,
ELECTRIC SHOCK OR INJURY TO PERSONS:
• The shaver should never be left unattended when
plugged into a power outlet, except when charging the
shaver.
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
• Use this shaver only for its intended use as described in
this manual. Do not use attachments not recommended
by Remington.
• Never operate this shaver if it has a damaged cord or
plug, if it is not working correctly, if it has been dropped
or damaged, or dropped into water. If the supply cord or
plug of this shaver is damaged it must be replaced. It
cannot be repaired.
2

3
• Keep the cord away from heated surfaces.
• Charge, use and store the product at a temperature
between 0°C and 32°C.
• Never insert any object into any opening of this shaver.
• Do not use outdoors or where aerosol (spray) products
are being used, or where oxygen is being administered.
• Do not use the shaver with a damaged or broken tracks
or cutters, as injury may occur.
• For use on facial hair only. Not intended for shaving the
hair on your head.
• Do not plug or unplug the shaver with wet hands.
• For household use only.
Remington strongly recommends that an approved
Safety Switch (residual current device) be installed to
protect all bathroom power outlets. Ask an electrical
contractor for advice.
SAVE THESE INSTRUCTIONS
3

4
R6150AU & R8150AU TITANIUM SHAVER
USE & CARE INSTRUCTION MANUAL
Thank you for purchasing your new Remington® Titanium Rotary Shaver.
Inside this manual you will find tips on using and caring for your shaver.
KEY PARTS
1. Pivoting head & cutter assembly
2. Individual flexing heads
3. Head release button
4. Pop-up trimmer (rear)
5. On/Off push button
6. LCD screen
7. Power port
Also includes:
- Cleaning brush
- Storage pouch
- Protective head
guard
- Power adaptor
- Charging stand
(R8150AU)
2
3
1
6
5
7
4

5
SPECIFICATIONS R6150AU R8150AU
Power System Cord/Cordless Cord/Cordless
Initial Charge Time 24 Hours 24 Hours
Full Charge Time 90 Minutes 90 Minutes
Cordless Shave Time 60 Minutes 60 Minutes
Quick Charge Yes Yes
Indicators LCD LCD
Voltage Type Worldwide Worldwide
Charging Stand No Yes
Replacement Part No. SP-5161AH SP-5161AH
Power System: Cord/Cordless – shaver can be used with or without the power cord.
Quick Charge: Shaver will charge long enough for one shave in 5 minutes.
Indicator: LCD Panel – displays the number of minutes of remaining battery power.
Voltage Type: Worldwide Voltage – shaver automatically adapts to an outlet
voltage between 100V and 240V.
Note: Some countries will require the use of a plug adaptor that is not included
with your shaver.

6
CHARGING
1. Plug power adaptor into shaver. (Diagram A)
2. Plug power adaptor into wall outlet. (Diagram B)
3. Charge shaver for 24 hours before its first use. This first charge is important
to the shaver’s battery life. Note: During initial charge ignore the electronic
indicators as they are in “start up cycle”. (Diagram C)
4. Use shaver until recharge is required.
CAUTION!
• Make sure the shaver and your hands are dry when charging the shaver.
• Always charge the shaver in a cool, dry place.
SHAVING
1. Press power button to turn on. (Diagram D)
2. Shave face and neck using short, circular strokes. (Diagram E)
3. After shaving, turn the shaver off. (Diagram D)
**Remington recommends that you use your new shaver daily for up to
three weeks to allow time for your hair and skin to become
accustomed to the new shaving system**

7
SHAVING TIPS
• Ensure your skin is dry and free of oils.
• Wait at least 15 minutes after getting up before shaving, to ensure your face
is free of puffiness that may be present from sleeping.
• Always hold the shaver at a right angle to the skin so that all three heads
are touching the skin with equal pressure.
• Stretch skin with the free hand so hairs stand upright, making it easier for
them to enter the cutting chamber.
• Use moderate to slow, circular stroking movement.
• The use of short, circular motions in stubborn areas may obtain a closer
shave, especially along the neck and chin line.
• Do not press hard against the skin to avoid skin irritation and/or damage to
the rotary heads.
TRIM
1. Pull trimmer release button to engage trimmer. (Diagram F)
2. Trim long, difficult hairs and side burns. (Diagram G)
3. Close trimmer by pressing down. (Diagram H)

8
CLEANING & CARE
The shaver is a washable appliance. The head assembly part may
be cleaned under warm water.
NOTE: **When cleaning your shaver, make sure the shaver is
turned off and disconnected from the power cord.**
CAUTION!
• To clean the external surfaces of the shaver, use a damp cloth. Do not use
strong detergents or other chemicals.
• To dry, wipe the surface of the shaver with a dry towel. Do not use a hair
dryer or heater to dry the shaver.
•The shaver should not be used until it has dried.






I J KL
M
Q
N
R
OP
Daily:
1. Press the release button on front of shaver and open head assembly.
(Diagram I)
2. Tap out excess hair shavings. (Diagram J)
3. Rinse the head of the shaver in running water.
NEVER submerge the shaver in water!
4. Close head assembly. (Diagram K)

Weekly:
1. Perform the daily cleaning steps 1 and 2.
2. Remove the cover from the hair pocket assembly. (Diagram L) Place the
body of the shaver aside to ensure that it will not get wet.
3. Release the inner cutter carrier by rotating the locking arms counter-
clockwise. (Diagram M)
4. Remove the inner cutter carrier away from the cutters. (Diagram N)
5. Remove the cutters. (Diagram O)
6. Thoroughly rinse away any debris from inner and outer cutters. (Diagram P)
7. Replace the inner cutters. (Diagram Q)
8. Place the inner cutter carrier back into position and lock into place by
rotating the locking arms clockwise until they snap into place. (Diagram R)
9. Lubricate each cutter with Remington Shaver Saver (SP4).
10. Close the head assembly. (Diagram K)
** Trimmer: Lubricate teeth with oil every six months
Replace head icon
• The replace head icon on the LCD display will flash at a 1 second interval
every time the shaver reaches 600 minutes of operation.
• This symbol means that it is time to replace your shaver head.
• The replace head icon will flash for 9 minutes and then turn off.
• If the shaver is turned off and then on the icon will continue to flash until
the total time the icon flashes has reached 9 minutes.
• If the replace head icon is flashing when the shaver is turned off it will
continue to flash for 15 sec. and then stop.
9

Money Back Offer - Australia/New Zealand Only
If within 30 days you are not fully satisfied with your Remington® shaver,
just return the shaver with this completed coupon and a copy of your
Australian/New Zealand purchase receipt to Remington®. In return, we
will send you a cheque for the full purchase price of the shaver. Please
allow 6-8 weeks for your cheque to arrive.
Name: _________________________________________________
Address:_______________________________________________
City:_____________________ State:________ Postcode: ________
10
This product is not suitable to use in a bath or shower.
This product conforms to radio frequency interference requirements.
Any product purchased and used commercially carries a limited 90 Day Warranty.
REPLACING YOUR HEADS AND CUTTERS
Please refer to the shaver grid on page 5 of this manual that lists the correct
replacement part number for your shaver.
It is very important to replace your head and cutters when necessary to ensure a
close, comfortable shave without irritation. We recommend they be replaced
every 6 months. Here are some signs of head and cutter wear, indicating that
replacement is needed:
• Irritation: As the heads get excessively worn you may experience some skin
irritation. This would be especially noticeable when you apply moisturizing
lotion.
• Pulling: When the cutters wear you may feel a sense of pulling and a loss
of closeness when you shave. This is an indication that it is time to replace
your heads and cutters.