Remington HC4255 User manual

QuickCut Hair Clipper
HC4255
I remington-europe.com
Register online for an EXTRA year guarantee
Visit uk.remington-europe.com/product-registration You must register within 28 days of purchase.

2
Fig. 1 Fig. 4Fig. 3Fig. 2
f
j
i
e
g

3
Thank you for buying your new Remington® product. Please read these instructions
carefully and keep them safe. Remove all packaging before use.
IMPORTANT SAFEGUARDS
• This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been supervised/instructed and
understand the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be done by children
unless they are older than 8 and supervised. Keep the appliance and cable
out of reach of children under 8 years.
The device is suitable for cleaning under an open water tap.
• WARNING: Detach the device from the charging adapter before cleaning it
in water.
• Do not use the product with a damaged cord. A replacement can be
obtained via our International Service Centres.
• This product should only be used with the charging adaptor supplied.
• Do not use attachments other than those we supply.
• The charging adaptor contains a transformer. Do not cut o the adaptor to replace
it with another plug, as this causes a hazardous situation.
• Do not use the appliance if it is damaged or malfunctions.
• Do not plug or unplug the appliance with wet hands.
• This appliance is not intended for commercial or salon use.
PARTS
1. On/o switch
2. Blade set
3. 9 attachment guide combs
4. Washout port
5. Charging indicator
Not shown:
• Cleaning brush
• Oil bottle
• Adaptor
• Travel pouch
• Hair cape

4
GETTING STARTED
CHARGING YOUR APPLIANCE
Note: It is recommended to fully charge your appliance before using for the rst time.
Please refer to the charge times shown in this book.
• Connect the product to the adaptor and then to the mains.
• When charging the charge indicator will slowly ash.
CHARGE LEVEL INDICATORS
Charge Level Indicator
Charging LED blinks
Fully charged LED solid
• Run time from fully charged is up to 40 minutes.
• Charge time from empty is 4 hours.
Note: To preserve the life of your batteries, let them run out every 6 months then fully
charge.
QUICK CHARGE FUNCTION
• 10 minutes charging will give an emergency burst of run time.
INSTRUCTIONS FOR USE
• For corded use connect the product to the adaptor, then to the mains.
CAUTION Extended mains only use will result in the reduction of the battery life.
CORDLESS USE
• When the unit is switched on and fully charged, the product can be used in cordless
mode for up to 40 minutes.
• Switch the product on by pressing the on/o switch.
BEFORE STARTING THE CUT
• Inspect the clipper making sure that it is free from hair and dirt.
• Before cutting, always comb the hair so it is tangle free and dry.
Guide Comb Cutting length
1 (Grade 0) 1.5mm
22mm
3 2.5mm
4 (Grade 1) 3mm

5
Guide Comb Cutting length
5 4.5mm
6 (Grade 2 6mm
7 (Grade 3) 9mm
8 (Grade 4) 12mm
9 (Grade 5) 15mm
• Use the clipper without any xed combs for trimming hair close to the skin.
• This will trim hair to 1mm, holding the clipper so the blades are perpendicular to
the skin will trim hair to 0.5mm.
TO ATTACH A COMB
• Hook the front edge of the comb to the front teeth of the wide trimmer blade. Then
push the back of the comb down until it snaps in place.
TO REMOVE THE COMB
• Push up the back of the comb until it clicks o the clipper blade.
INSTRUCTIONS FOR CUTTING HAIR
• The QuickCut Clipper’s ergonomic design provides many dierent ways of holding
the clipper in use.
• For clipping the top of the head (see g. 1).
• For clipping the back of the head (see g. 2).
• For clipping the sides of the head (see g. 3).
• For detailing (see g. 4).
• For even cutting, allow the comb attachment/blade to cut its way through the hair.
Do not force it through quickly. If you are cutting for the rst time, start with the
maximum comb attachment.
• For one all over cut length, attach the desired guide comb and slowly guide the
clipper through the hair against the direction the hair normally grows.
• Remove the guide comb. To produce a clean straight line at the sideburns and the
base of the neck, reverse the hair clipper. Place the reversed clipper at right angles
to the head, tips of the blades lightly touching the skin and then work downwards.
The following instructions are for those users who want dierent trimming lengths on
the sides, back and top of the head
STEP 1 – NAPE OF THE NECK
• Set the comb to 3mm or 6mm.
• Hold the clipper with the blade teeth pointing upwards. Begin starting at the centre
of the head at the base of the neck.