Remington PG6000 User manual

G6 Graphite Series
Personal Groomer
PG6000
I www.remington.co.uk
Register online for an EXTRA year guarantee
Visit uk.remington-europe.com/product-registration You must register within 28 days of purchase.

2
e
f
i
m
n
g
j
k
l
h
A
3 mm
6 mm
9 mm
rs
o
1
23

3
Thank you for buying your new Remington® product. Please read these instructions
carefully and keep them safe. Remove all packaging before use.
IMPORTANT SAFEGUARDS
• This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been supervised/instructed and
understand the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be done by children
unless they are older than 8 and supervised. Keep the appliance and cable
out of reach of children under 8 years.
• The adaptor contains a transformer. Do not cut off the adaptor to replace it
with another plug, as this causes a hazardous situation.
E Suitable for use in a bath or shower.
• WARNING: Detach the shaver from the charging adapter before cleaning it
in water.
• Do not use the product with a damaged cord.
• WARNING: For recharging the battery, only use the charger supplied with
the appliance - type reference PA-0505U (UK).
• Always replace a damaged adaptor with one of the original type.
• The battery in this device is not replaceable.
• Do not use the appliance if it is damaged or malfunctions.
• Do not use attachments other than those we supply.
• This appliance should never be left unattended when plugged into a power outlet,
except when charging.
• Keep the power plug and cord away from heated surfaces.
• Do not plug or unplug the appliance with wet hands.
• Do not twist or kink the cable, or wrap it round the appliance.
• This appliance is not intended for commercial or salon use.

4
PARTS
1. On/O switch
2. Charging indicator light
3. Charging connector
4. Wide trimmer
5. Adjustable comb
6. Fixed guide combs
7. Precision trimmer
8. Nose, ear, eyebrow trimmer
9. Mini foil shaver
10. Deep cleansing brush head
11. Body hair trimmer
12. Body hair trimmer comb
13. Adaptor (not shown)
14. Storage pouch (not shown)
CHARGING YOUR APPLIANCE
Before using your trimmer for the rst time, charge for 4 hours.
1. Ensure the product is switched o.
2. Connect the charging adaptor to the product and then to the mains.
CHARGING INDICATOR LIGHT
Charge Level Indicator
Charging Blue LED will ash
Fully Charged Blue LED will light up continuously
Battery charge is low Red LED will ash
• Your trimmer cannot be overcharged. However, if it is not going to be used for an
extended period of time (2-3 months), unplug it from the mains and store.
• To preserve the life of your batteries, let them run out every 6 months then recharge
for 4 hours.
• On a full charge, your beard trimmer will run for up to 90 minutes of cordless usage.
ATTACHMENTS
TO FIT AND REMOVE ATTACHMENTS FIG. A
Ensure that the device is switched o before tting or removing attachments.
• To remove, rotate the attachment anti-clockwise until it unlocks and then lift it o.
• To t, place the desired attachment on top of the device and rotate the attachment
clockwise to lock it into place.

5
FITTING AND REMOVING FIXED GUIDE COMBS
To Fit
• Hook the front of the guide comb over the teeth of the wide trimmer.
• Press the back of the guide comb down until it clicks into place.
To Remove
• Lift the tab on the back of the guide comb upwards until it comes free from the wide
trimmer head.
FITTING AND REMOVING THE ADJUSTABLE COMB
• To t, line up the rails on the comb with the slots on the sides of the groomer and
slide the comb downwards onto the groomer.
• To adjust, press and hold the adjustment button on the back of the comb and slide
the comb up or down. Release the button to lock the comb at that position. The
length of cut is indicated by the scale on the side of the trimmer.
• To remove, press and hold the adjustment button and push the comb up and o the
groomer.
INSTRUCTIONS FOR USE
• Comb facial hair with a ne comb before you start trimming.
• Comb your hair in the direction that it grows so that the hairs are at their maximum
height and facing in the same direction.
• After trimming, lightly go over the trimmed areas with the foil to get a smooth clean
nish.
• Since all hairs do not grow in the same direction, you may want to try dierent
trimming positions (i.e. upwards, downwards or across) for better results.
• Hair should be dry and free from any waxes or lotions.
• If hair builds up during use, switch the unit o, remove any attachment in use and
clean any excess hair clippings from the attachment and groomer.
3DAY STUBBLE, AND BODY HAIR MAINTENANCE
Attachments
Wide trimmer with 1.5 mm xed comb
Body hair attachment
3-day stubble look:
Let your stubble grow to a length that is slightly longer than the look you are trying to
achieve.
1. Fit the 1.5 mm xed comb to the wide trimmer attachment.
2. Run your trimmer through your beard against the direction of hair growth.

6
3. Tidy the edges of the stubble using the precision trimmer attachment.
• For more control over the length of your stubble, you can use the adjustable comb
and trim your stubble down in increments starting at a longer length setting until
you get the desired look.
Body hair maintenance: Trimming to length
1. Fit the body hair attachment.
2. Body hair can be trimmed to 3 dierent lengths (3, 6 and 9 mm). Select the desired
length by sliding the comb into one of the three slots on the side of the attachment.
3. Place the at side of the attachment against the skin.
4. Slowly slide the trimmer through the hair in the direction of hair growth.
5. Use slow, well-controlled movements.
Body hair maintenance: Removal
1. Remove the comb from the body hair attachment and go over the areas where you
want to remove the body hair.
2. Stretch the skin with your free hand to make the hairs stand upright.
3. Use light pressure and shave against the direction of hair growth.
HAIR CLIPPING
Attachments
Wide trimmer with adjustable comb
Step 1: Nape of the neck
1. Fit the wide trimmer and adjustable comb.
2. Set the adjustable comb to 4 mm or 6 mm.
3. Hold the clipper with the blade teeth pointing upwards. Begin starting at the centre
of the head at the base of the neck.
4. Slowly lift the clipper, working upwards and outwards through the hair, trimming
just a little at a time.
Step 2: Back of the head
• With the comb set at 12 mm or 18 mm, cut the hair at the back of the head.
Step 3: Side of the head
1. Adjust the comb to a shorter length setting for the areas around the ears.
2. Increase the length setting on the adjustable comb to gradually transition the length
of hair on the side of the head to the longer hair on the top of the head.
Step 4: Top of the head
1. Adjust the comb to the longer length settings (up to 20 mm) then cut the hair on top
of the head against the direction in which the hair normally grows.
2. Always work from the back of the head.

7
Trim the sideburns
• To trim the sideburns, adjust the comb to the desired length setting, or use one of
the xed guide combs.
SHORT/LONG BEARD TRIMMING
Attachments
Wide trimmer with adjustable comb
Precision trimmer
1. Fit the wide trimmer and adjustable comb.
2. Set the adjustable comb to the desired length.
3. Start trimming under the chin following the line of the jaw.
4. Work upwards towards the ear and upper beard line.
5. Tidy the beard edges using the precision trimmer attachment.
CONTOUR EDGING AND CLOSE HAIR CUTTING
Attachments
Wide trimmer
Contour edging:
1. Hold the device with the cutting blade (teeth) facing you and at 90 degrees to the
skin.
2. Start with the edge of the beard/moustache line and, with the blade resting lightly
against the skin, use slow controlled movements to create contoured lines.
Close hair cutting:
1. Use the ngers of one hand to lift the hair at the base of your head up o your neck.
2. Your index nger should be covering the roots of the hairs you are lifting to prevent
them from being accidentally cut.
3. Hold the trimmer to the base of your neck with the blade facing up. Move the
trimmer up the neck until it touches your index nger which is protecting the hair
roots.
4. Move your trimmer slowly and keep the hair roots at the base of your head out of the
way of the trimmer.
DETAILED NOSE, EYEBROW AND EAR HAIR TRIMMING
Attachments
Nose, ear and eyebrow trimmer
Nose and ear:
1. Fit the nose, ear and eyebrow trimmer.

8
2. Insert the attachment gently into the nostril or ear.
3. Gently move the attachment in and out while rotating the body of the groomer at
the same time.
• Don’t insert the attachment more than 6 mm.
• Wash the attachment after each use.
Eyebrow:
1. Carefully guide the attachment to remove any stray or longer hairs from the
eyebrow.
2. To completely remove hairs, let the attachment touch the skin then move over the
desired area.
MICRO STUBBLE AND PRECISION TRIMMING
Attachments
Precision trimmer
Micro stubble:
The precision trimmer attachment has Trim Shave Technology which trims hair down to
0.2 mm to leave a micro stubble nish.
1. Fit the precision trimmer.
2. Hold the attachment so that the guide on the lower edge of the blade contacts the
skin (the same way you would hold a wet razor). The guide on the lower edge of the
blade helps to stretch the skin during trimming.
3. Use motions similar to wet shaving.
Precision trimming:
1. Hold the precision trimmer attachment perpendicular to the skin.
2. Move it towards or away from the beard hair to achieve the desired result. Use gentle
pressure and controlled movements.
DEEP CLEANSING BRUSH HEAD
Attachments
Deep cleansing brush head
1. Moisten the brush bristles by running under water. NOTE: DO NOT use the brush
head whilst completely dry as this can cause skin irritation.
2. Dampen your skin with water and apply face wash onto your skin. Alternatively,
apply your face wash directly onto the brush.
3. We recommend cleansing with the Deep Cleansing brush in 3 sections:
• T-Zone (1), Right side (2) and Left side (3).
4. Switch on using the On/O button.

9
5. Place the facial brush directly onto your skin.
6. Gently glide the brush over the skin and beard in circular motions avoiding the
delicate eye area.
NOTE: Try to avoid applying too much pressure with the brush when directly on the skin.
CLEAN SHAVEN EDGING
Attachments
Mini Foil Shaver
1. Hold the trimmer so the mini foil shaver gently touches your face.
2. Use short, well-controlled movements to shave around your beard moustache. Use
your free hand to stretch your skin. This encourages the hair to stand upright,
making it easier to shave.
• Note: The mini foil shaver was designed to shave the detail areas around your beard/
moustache/sideburns. It was not designed to shave your entire face. For a close
comfortable shave, guaranteed, use one of Remington’s electric shavers.
CARE FOR YOUR GROOMER
Care for your product to ensure a long lasting performance. We recommend that you
clean your groomer after each use.
AFTER EACH USE
• Brush any accumulated hairs from the groomer and attachment heads.
• The easiest and most hygienic way to clean the groomer is by detaching the head
from the groomer body and rinsing the head with warm water.
• The groomer body should not be rinsed.
• Place one or two drops of cutter oil or sewing machine oil on the blades.
• Turn the clipper on to distribute the oil evenly, wipe o any excess oil.
BATTERY REMOVAL
We strongly recommend that a professional removes the rechargeable battery. Parts of
the shaver case, and tools have sharp edges and may cause injury if not handled
correctly.
• The rechargeable battery must be removed from the appliance before it is scrapped.
• Disconnect the charging adapter before removing the battery.
1. Ensure the device is discharged of all power. To do this, switch it on and allow it to
run until it stops.
2. Using a suitable tool, carefully pry apart the front and rear halves of the case at the
joint line.

10
3. Remove the two screws that hold the transparent inner case to the back half of the
outer case.
4. Lift out the inner case.
5. Pull the black motor holder o the transparent case.
6. Slide the circuit board and battery out of the transparent inner case.
7. Cut the tabs holding the battery to the circuit board.
• Used batteries must be removed from the appliance and disposed of at an
appropriate ocial recycling/collection point.
• Do not attempt to operate the shaver once you have opened it.
RECYCLING
WTo avoid environmental and health problems due to hazardous
substances, appliances and rechargeable and non-rechargeable
batteries marked with one of these symbols must not be disposed of
with unsorted municipal waste. Always dispose of electrical and
electronic products and, where applicable, rechargeable and
non-rechargeable batteries, at an appropriate ocial recycling/
collection point.
SERVICE AND GUARANTEE
Defects aecting product functionality appearing within the
guarantee period will be corrected by replacement or repair at our
option provided the product is used and maintained in accordance
with the instructions. Your statutory rights are not aected.
This warranty shall not be valid where it is contrary to U.S. and other
applicable laws, or where the warranty would be prohibited under
any economic sanctions, export control laws, embargos, or other restrictive trade
measures enforced by the United States or other applicable jurisdictions. This includes,
without limitation, any warranty claims implicating parties from, or otherwise located in,
Cuba, Iran, North Korea, Syria and the Crimea region.
To claim an extra 1 year guarantee, register your product online within 28 days of
purchase.
Register at: https://uk.remington-europe.com/product-registration
Consumables are guaranteed only for their recommended lifecycle. Replacement/spare
parts* are excluded and are only covered by a 1 year warranty.
*Examples include, but are not limited to, adaptors, haircare attachments, grooming accessories, etc.
£

11
SERVICE CENTRE
UNITED KINGDOM
G 0800 212 438 (free call mainland UK)
Spectrum Brands (UK) Ltd
Fir Street, Failsworth, Manchester
M35 0HS, UK
www.remington.co.uk
IRELAND
G 142 951 40
Remington Consumer Products,
Unit B12, Ballymount Corporate Park,
Ballymount, Dublin 12
https://ie.remington-europe.com

Ref. No. PG6000
Type No. PG05A
19/UK/ PG6000 T22-7001152 Version 10 /19
Remington® is a Registered Trade Mark of Spectrum Brands, Inc., or one of its subsidiaries.
Spectrum Brands (UK) Ltd
Fir Street,
Failsworth,
Manchester
M35 0HS
www.remington.co.uk
© 2019 Spectrum Brands, Inc.