Remington HF9000 User manual

HF9000
NOTE: **When cleaning your shaver,
make sure the shaver is turned off and
disconnected from the power cord.**
For optimal shaver performance, clean
your shaver after each use.
■ Do not remove or replace head
assembly while shaver is running as it
may cause damage to the unit’s screens
and cutters.
■ To clean the external surfaces of the
shaver, use a damp cloth. Do not use
strong detergents or other chemicals.
■ To dry, wipe the surface of the shaver
with a dry towel. Do not use a hair dryer
or heater to dry the shaver.
■ The shaver should not be used until it
has dried.
■ Lubricate each cutter with household oil.
■ This shaver has no user serviceable
parts.
Daily Cleaning:
1. Grasp the sides of the cutter assembly
and pull away from the shaver body.
2. Tap the stubble from the foils and
cutters.
3. Replace the hairpocket assembly.
Monthly Cleaning:
1. Grasp the sides of the cutter assembly
and pull away from the shaver body.
2. Tap the stubble from the foils and
cutters.
3. Use the cleaning brush to delicately
sweep any loose hairs from the cutters
and trimmer.
4. After cleaning, replace
the hairpocket
assembly.
Replacing the Foils & Cutters
To ensure the continued highest quality
performance from your shaver, we recom-
mend that foils and cutters are replaced
regularly.
Signs that your foils and cutters need
replacing:
■ Irritation: As foils get worn, you may
experience skin irritation.
■ Pulling: As the cutters wear, your shave
may not feel as close and you may feel
your cutter pulling your hair.
■ Wear through: You may notice that the
cutters have worn through the foils.
To Replace the Foil
1. Grasp the foil carrier grips on the sides
of the shaver and pull up to remove the
foils. Discard the used foils.
2. Snap a new foil carrier in place.
To Replace the Cutters
1. Remove the foil carrier.
2. Depress cutter and rotate it 90°
counterclockwise and lift off. Do not lose
spring.
3. Place new cutter on oscillator tip,
depress and rotate 90° counterclockwise.
NOTE: Do not press on the cutter ends as
this may cause damage.
Note: It is recommended to fully charge
your appliance before using for the first
time. Please refer to the charge times
shown in this book.
1. Connect the cord to the shaver and then
to the electrical outlet. The charging
indicator light will glow green.
2. Charge your new shaver for 2 hours
before its first use. This first charge is
important to the shaver’s battery life.
■ Ensure the product is switched off.
■ Connect the adaptor to the product and
then to the mains.
■ Run time from fully charged is up to 60
minutes.
Note: To preserve the life of your batteries,
let them run out every 6 months then
fully charge.
1. Slide trimmer release button up to
engage trimmer.
2. Trim long, difficult hairs and side burns.
3. Close trimmer by pressing down.
Before using, read the important safety
instructions in front of the manual.
1. Begin by removing the protective head
guard from your shaver.
2. Slide the on/off button up to turn on.
(Dia. D)
3. Slide trimmer button up to engage and
use it to remove long hair first. Then
close down when finished.
(Dia. E_F)
4. Stretch the skin with your free hand so
the hairs stand upright.
5. Hold the shaving head so all screens
touch your skin simultaneously.
The independently floating screens
automatically adjust to the contours of
your face. Only apply light pressure on
the shaving head while shaving and
use short, circular strokes. (Dia. G)
6. After shaving, turn the shaver off.
(Dia. D)
*We recommend that you use your new
shaver daily for up to three weeks to
allow time for your hair and skin to
become accustomed to the new shaving
system.**
■ Ensure your skin is dry and free of oils.
■ Wait at least 15 minutes after getting
up before shaving, to ensure your face
is free of puffiness that may be present
from sleeping.
■ Always hold the shaver at a right angle
to the skin so the screens are touching
the skin with equal pressure.
■ Stretch skin with the free hand so hairs
stand upright, making it easier for them
to enter the cutting chamber.
■ Shave with short, circular strokes. The
use of short, circular motions in stubborn
areas may obtain a closer shave,
especially along the neck and chin line.
■ Do not press hard against the skin in
order to avoid damage to the screens.
When your rechargeable shaver reaches the end
of its useful life, the batteries must be removed
from the shaver and recycled or disposed of
properly in accordance with your state and local
requirements. If this is not required by law, you
may elect to dispose of the shaver with the
batteries.
This device uses one of the following types of
rechargeable batteries: nickel metal hydride
(NiMH), nickel cadmium (Ni-Cd) or Lithium
Ion (Li-Ion) (see included battery for indication
of type).
CAUTION: ALL RECHARGEABLE BATTERIES
MUST BE RECYCLED OR DISPOSED OF IN
ACCORDANCE WITH APPLICABLE STATE AND
LOCAL REGULATIONS. DO NOT PUT IN FIRE
OR MUTILATE, AS THE BATTERY MAY BURST
OR RELEASE TOXIC MATERIALS. DO NOT
SHORT-CIRCUIT, AS THIS MAY CAUSE BURNS.
To Remove the Rechargeable Battery:
1. Remove phillips head screw from lower back
panel of shaver.
2. Pry the back panel off the shaver releasing
the snap fits.
3. Snip the battery wires and remove the
batteries.
4. Dispose of batteries properly.
■ Never drop or insert any object into any
of the appliance’s openings.
■ Do not wrap the cord around the
appliance.
■ Do not use outdoors or operate where
aerosol (spray) products are being used
or where oxygen is being administered.
■ Do not use an extension cord or a
voltage converter with this appliance.
■ Do not use outdoors or operate where
aerosol (spray) products are being used
or where oxygen is being administered.
■ Always attach the plug to the appliance,
then to outlet. To disconnect, turn all
controls to OFF, then remove plug from
outlet.
■ Detach removable power cords from
appliance for storage.
■ Always pull on cord plug to unplug from
wall socket. Never pull on electric cord.
■ Do not plug or unplug this appliance
when your hands are wet.
■ Do not use this appliance with a
damaged or broken head or cutters, as
facial injury may occur.
■ Always store this appliance and cord in
a moisture-free area. Do not store it in
temperatures exceeding 140°F (60°C).
■ Detach removable power cords from
appliance for storage.
■ Shavers, including the trimmer, are for
use on facial hair only. They should not
be used for shaving the hair on your
head or any other part of your body.
■ For additional protection the installation
of a residual current device (RDC) with
a rated residual operating current not
exceeding 30mA is advisable. Ask an
electrician for advice (Argentina/Chile).
When using an electrical appliance, basic
precautions should always be observed,
including the following. Read all instruc-
tions before using this shaver.
DANGER
To reduce the risk of electric shock:
■ Except when charging, always unplug
this appliance from the electrical outlet
immediately after using.
■ Do not use while bathing or in the
shower.
■ Do not place or store this appliance
where it can fall or be pulled into a tub
or sink.
■ Do not place or drop into water or other
liquid.
■ Detach the appliance from the power
supply cord before cleaning.
■ Do not reach for an appliance that has
fallen into water. Unplug it immediately.
■ Use only when the shaver is in dry
condition.
■ Do not submerge in water.
WARNING
To reduce the risk of burns, fire,
electric shock, or injury to persons:
■ An appliance should never be left
unattended when it’s plugged in, except
when charging a rechargeable appliance.
■ Close supervision is necessary when
this appliance is used by, on, or near
children, or individuals with special
needs or certain disabilities.
■ Children should be supervised to ensure
they do not play with the appliance.
■ Use this appliance only for its intended
use as described in this manual. Do not
use attachments not recommended by
the manufacturer.
■ Suitable for cleaning under an open
water tap.
■ Detach the hand-held part from the
supply cord before cleaning in water.
■ Never operate this appliance if it has a
damaged cord or plug, if it is not working
properly, if it has been dropped or
damaged, of if it has been dropped into
water. Return the appliance to a service
center for examination and repair.
Note: If the power cord is damaged, it
must be replaced by personnel or
an authorized service center in Latin
America.
■ The appliance must only be used with
the power supply unit supplied with the
appliance.
■ Class III devices must establish that
they must only be supplied at a very
low safety voltage corresponding to that
marked on the device.
■ For washable models having supports or
bases, they must be installed so that they
can not fall into the water.
■ Keep the cord away from heated
surfaces.
Use and Care Guide
IMPORTANT SAFETY
INSTRUCTIONS
Guarantee - See insert
® Registered Trademark of Spectrum
Brands, Inc.
© 2018 Spectrum Brands, Inc.
11/18 Job#24521-00 T22-7000759-A
Dist. by: Spectrum Brands, Inc.,
Middleton, WI 53562
Designed in USA
MADE IN CHINA
HF9000:
Electrical Characteristics:
100-240V~ 50/60Hz 200mA
SAVE THESE INSTRUCTIONS
CAUTION: This product
is not suitable for use
in bath or shower.
It is recommended that you use your new
shaver daily for up to two weeks to allow
time for your beard and skin to become
accustomed to the new shaving system.
Your Remington Sensitive Foil shaver has
been designed to help reduce irritation
and ingrowing hairs for men who experi-
ence these conditions when shaving. The
lifting combs at both edges of the cutting
head help lift flat lying, longer hairs and
feed them into the cutters. The shaver is
designed to cut hairs at or slightly above
the skin surface to help prevent ingrown
hairs. For best results, it is recommended
to use the shaver daily or every other
day to maintain hair length and to reduce
ingrowing hairs.
Charging
Shave
Trim
Shaving Tips Cleaning & Care
Battery Removal
1. Shaving foils
2. Trimmer
3. On/off switch
4. Hair pocket
5. Pop-up trimmer
6. Foil assembly release button
7. Charging indicator.
8. Charging connector. Includes USB cable
(not shown)
Replacements
Getting Started
The blades are washable
under a running tap.
1
8
2
63
5
4
7
Charging Indicator
Charging Level Indicator
Charging LED flashes slowly
Low charge LED flashes quickly
Full charge LED comes on for 5 minutes then goes off

HF9000
NOTE: **When cleaning your shaver,
make sure the shaver is turned off and
disconnected from the power cord.**
For optimal shaver performance, clean
your shaver after each use.
■ Do not remove or replace head
assembly while shaver is running as it
may cause damage to the unit’s screens
and cutters.
■ To clean the external surfaces of the
shaver, use a damp cloth. Do not use
strong detergents or other chemicals.
■ To dry, wipe the surface of the shaver
with a dry towel. Do not use a hair dryer
or heater to dry the shaver.
■ The shaver should not be used until it
has dried.
■ Lubricate each cutter with household oil.
■ This shaver has no user serviceable
parts.
Daily Cleaning:
1. Grasp the sides of the cutter assembly
and pull away from the shaver body.
2. Tap the stubble from the foils and
cutters.
3. Replace the hairpocket assembly.
Monthly Cleaning:
1. Grasp the sides of the cutter assembly
and pull away from the shaver body.
2. Tap the stubble from the foils and
cutters.
3. Use the cleaning brush to delicately
sweep any loose hairs from the cutters
and trimmer.
4. After cleaning, replace
the hairpocket
assembly.
Replacing the Foils & Cutters
To ensure the continued highest quality
performance from your shaver, we recom-
mend that foils and cutters are replaced
regularly.
Signs that your foils and cutters need
replacing:
■ Irritation: As foils get worn, you may
experience skin irritation.
■ Pulling: As the cutters wear, your shave
may not feel as close and you may feel
your cutter pulling your hair.
■ Wear through: You may notice that the
cutters have worn through the foils.
To Replace the Foil
1. Grasp the foil carrier grips on the sides
of the shaver and pull up to remove the
foils. Discard the used foils.
2. Snap a new foil carrier in place.
To Replace the Cutters
1. Remove the foil carrier.
2. Depress cutter and rotate it 90°
counterclockwise and lift off. Do not lose
spring.
3. Place new cutter on oscillator tip,
depress and rotate 90° counterclockwise.
NOTE: Do not press on the cutter ends as
this may cause damage.
Note: It is recommended to fully charge
your appliance before using for the first
time. Please refer to the charge times
shown in this book.
1. Connect the cord to the shaver and then
to the electrical outlet. The charging
indicator light will glow green.
2. Charge your new shaver for 2 hours
before its first use. This first charge is
important to the shaver’s battery life.
■ Ensure the product is switched off.
■ Connect the adaptor to the product and
then to the mains.
■ Run time from fully charged is up to 60
minutes.
Note: To preserve the life of your batteries,
let them run out every 6 months then
fully charge.
1. Slide trimmer release button up to
engage trimmer.
2. Trim long, difficult hairs and side burns.
3. Close trimmer by pressing down.
Before using, read the important safety
instructions in front of the manual.
1. Begin by removing the protective head
guard from your shaver.
2. Slide the on/off button up to turn on.
(Dia. D)
3. Slide trimmer button up to engage and
use it to remove long hair first. Then
close down when finished.
(Dia. E_F)
4. Stretch the skin with your free hand so
the hairs stand upright.
5. Hold the shaving head so all screens
touch your skin simultaneously.
The independently floating screens
automatically adjust to the contours of
your face. Only apply light pressure on
the shaving head while shaving and
use short, circular strokes. (Dia. G)
6. After shaving, turn the shaver off.
(Dia. D)
*We recommend that you use your new
shaver daily for up to three weeks to
allow time for your hair and skin to
become accustomed to the new shaving
system.**
■ Ensure your skin is dry and free of oils.
■ Wait at least 15 minutes after getting
up before shaving, to ensure your face
is free of puffiness that may be present
from sleeping.
■ Always hold the shaver at a right angle
to the skin so the screens are touching
the skin with equal pressure.
■ Stretch skin with the free hand so hairs
stand upright, making it easier for them
to enter the cutting chamber.
■ Shave with short, circular strokes. The
use of short, circular motions in stubborn
areas may obtain a closer shave,
especially along the neck and chin line.
■ Do not press hard against the skin in
order to avoid damage to the screens.
When your rechargeable shaver reaches the end
of its useful life, the batteries must be removed
from the shaver and recycled or disposed of
properly in accordance with your state and local
requirements. If this is not required by law, you
may elect to dispose of the shaver with the
batteries.
This device uses one of the following types of
rechargeable batteries: nickel metal hydride
(NiMH), nickel cadmium (Ni-Cd) or Lithium
Ion (Li-Ion) (see included battery for indication
of type).
CAUTION: ALL RECHARGEABLE BATTERIES
MUST BE RECYCLED OR DISPOSED OF IN
ACCORDANCE WITH APPLICABLE STATE AND
LOCAL REGULATIONS. DO NOT PUT IN FIRE
OR MUTILATE, AS THE BATTERY MAY BURST
OR RELEASE TOXIC MATERIALS. DO NOT
SHORT-CIRCUIT, AS THIS MAY CAUSE BURNS.
To Remove the Rechargeable Battery:
1. Remove phillips head screw from lower back
panel of shaver.
2. Pry the back panel off the shaver releasing
the snap fits.
3. Snip the battery wires and remove the
batteries.
4. Dispose of batteries properly.
■ Never drop or insert any object into any
of the appliance’s openings.
■ Do not wrap the cord around the
appliance.
■ Do not use outdoors or operate where
aerosol (spray) products are being used
or where oxygen is being administered.
■ Do not use an extension cord or a
voltage converter with this appliance.
■ Do not use outdoors or operate where
aerosol (spray) products are being used
or where oxygen is being administered.
■ Always attach the plug to the appliance,
then to outlet. To disconnect, turn all
controls to OFF, then remove plug from
outlet.
■ Detach removable power cords from
appliance for storage.
■ Always pull on cord plug to unplug from
wall socket. Never pull on electric cord.
■ Do not plug or unplug this appliance
when your hands are wet.
■ Do not use this appliance with a
damaged or broken head or cutters, as
facial injury may occur.
■ Always store this appliance and cord in
a moisture-free area. Do not store it in
temperatures exceeding 140°F (60°C).
■ Detach removable power cords from
appliance for storage.
■ Shavers, including the trimmer, are for
use on facial hair only. They should not
be used for shaving the hair on your
head or any other part of your body.
■ For additional protection the installation
of a residual current device (RDC) with
a rated residual operating current not
exceeding 30mA is advisable. Ask an
electrician for advice (Argentina/Chile).
When using an electrical appliance, basic
precautions should always be observed,
including the following. Read all instruc-
tions before using this shaver.
DANGER
To reduce the risk of electric shock:
■ Except when charging, always unplug
this appliance from the electrical outlet
immediately after using.
■ Do not use while bathing or in the
shower.
■ Do not place or store this appliance
where it can fall or be pulled into a tub
or sink.
■ Do not place or drop into water or other
liquid.
■ Detach the appliance from the power
supply cord before cleaning.
■ Do not reach for an appliance that has
fallen into water. Unplug it immediately.
■ Use only when the shaver is in dry
condition.
■ Do not submerge in water.
WARNING
To reduce the risk of burns, fire,
electric shock, or injury to persons:
■ An appliance should never be left
unattended when it’s plugged in, except
when charging a rechargeable appliance.
■ Close supervision is necessary when
this appliance is used by, on, or near
children, or individuals with special
needs or certain disabilities.
■ Children should be supervised to ensure
they do not play with the appliance.
■ Use this appliance only for its intended
use as described in this manual. Do not
use attachments not recommended by
the manufacturer.
■ Suitable for cleaning under an open
water tap.
■ Detach the hand-held part from the
supply cord before cleaning in water.
■ Never operate this appliance if it has a
damaged cord or plug, if it is not working
properly, if it has been dropped or
damaged, of if it has been dropped into
water. Return the appliance to a service
center for examination and repair.
Note: If the power cord is damaged, it
must be replaced by personnel or
an authorized service center in Latin
America.
■ The appliance must only be used with
the power supply unit supplied with the
appliance.
■ Class III devices must establish that
they must only be supplied at a very
low safety voltage corresponding to that
marked on the device.
■ For washable models having supports or
bases, they must be installed so that they
can not fall into the water.
■ Keep the cord away from heated
surfaces.
Use and Care Guide
IMPORTANT SAFETY
INSTRUCTIONS
Guarantee - See insert
® Registered Trademark of Spectrum
Brands, Inc.
© 2018 Spectrum Brands, Inc.
11/18 Job#24521-00 T22-7000759-A
Dist. by: Spectrum Brands, Inc.,
Middleton, WI 53562
Designed in USA
MADE IN CHINA
HF9000:
Electrical Characteristics:
100-240V~ 50/60Hz 200mA
SAVE THESE INSTRUCTIONS
CAUTION: This product
is not suitable for use
in bath or shower.
It is recommended that you use your new
shaver daily for up to two weeks to allow
time for your beard and skin to become
accustomed to the new shaving system.
Your Remington Sensitive Foil shaver has
been designed to help reduce irritation
and ingrowing hairs for men who experi-
ence these conditions when shaving. The
lifting combs at both edges of the cutting
head help lift flat lying, longer hairs and
feed them into the cutters. The shaver is
designed to cut hairs at or slightly above
the skin surface to help prevent ingrown
hairs. For best results, it is recommended
to use the shaver daily or every other
day to maintain hair length and to reduce
ingrowing hairs.
Charging
Shave
Trim
Shaving Tips Cleaning & Care
Battery Removal
1. Shaving foils
2. Trimmer
3. On/off switch
4. Hair pocket
5. Pop-up trimmer
6. Foil assembly release button
7. Charging indicator.
8. Charging connector. Includes USB cable
(not shown)
Replacements
Getting Started
The blades are washable
under a running tap.
1
8
2
63
5
4
7
Charging Indicator
Charging Level Indicator
Charging LED flashes slowly
Low charge LED flashes quickly
Full charge LED comes on for 5 minutes then goes off

HF9000
NOTE: **When cleaning your shaver,
make sure the shaver is turned off and
disconnected from the power cord.**
For optimal shaver performance, clean
your shaver after each use.
■ Do not remove or replace head
assembly while shaver is running as it
may cause damage to the unit’s screens
and cutters.
■ To clean the external surfaces of the
shaver, use a damp cloth. Do not use
strong detergents or other chemicals.
■ To dry, wipe the surface of the shaver
with a dry towel. Do not use a hair dryer
or heater to dry the shaver.
■ The shaver should not be used until it
has dried.
■ Lubricate each cutter with household oil.
■ This shaver has no user serviceable
parts.
Daily Cleaning:
1. Grasp the sides of the cutter assembly
and pull away from the shaver body.
2. Tap the stubble from the foils and
cutters.
3. Replace the hairpocket assembly.
Monthly Cleaning:
1. Grasp the sides of the cutter assembly
and pull away from the shaver body.
2. Tap the stubble from the foils and
cutters.
3. Use the cleaning brush to delicately
sweep any loose hairs from the cutters
and trimmer.
4. After cleaning, replace
the hairpocket
assembly.
Replacing the Foils & Cutters
To ensure the continued highest quality
performance from your shaver, we recom-
mend that foils and cutters are replaced
regularly.
Signs that your foils and cutters need
replacing:
■ Irritation: As foils get worn, you may
experience skin irritation.
■ Pulling: As the cutters wear, your shave
may not feel as close and you may feel
your cutter pulling your hair.
■ Wear through: You may notice that the
cutters have worn through the foils.
To Replace the Foil
1. Grasp the foil carrier grips on the sides
of the shaver and pull up to remove the
foils. Discard the used foils.
2. Snap a new foil carrier in place.
To Replace the Cutters
1. Remove the foil carrier.
2. Depress cutter and rotate it 90°
counterclockwise and lift off. Do not lose
spring.
3. Place new cutter on oscillator tip,
depress and rotate 90° counterclockwise.
NOTE: Do not press on the cutter ends as
this may cause damage.
Note: It is recommended to fully charge
your appliance before using for the first
time. Please refer to the charge times
shown in this book.
1. Connect the cord to the shaver and then
to the electrical outlet. The charging
indicator light will glow green.
2. Charge your new shaver for 2 hours
before its first use. This first charge is
important to the shaver’s battery life.
■ Ensure the product is switched off.
■ Connect the adaptor to the product and
then to the mains.
■ Run time from fully charged is up to 60
minutes.
Note: To preserve the life of your batteries,
let them run out every 6 months then
fully charge.
1. Slide trimmer release button up to
engage trimmer.
2. Trim long, difficult hairs and side burns.
3. Close trimmer by pressing down.
Before using, read the important safety
instructions in front of the manual.
1. Begin by removing the protective head
guard from your shaver.
2. Slide the on/off button up to turn on.
(Dia. D)
3. Slide trimmer button up to engage and
use it to remove long hair first. Then
close down when finished.
(Dia. E_F)
4. Stretch the skin with your free hand so
the hairs stand upright.
5. Hold the shaving head so all screens
touch your skin simultaneously.
The independently floating screens
automatically adjust to the contours of
your face. Only apply light pressure on
the shaving head while shaving and
use short, circular strokes. (Dia. G)
6. After shaving, turn the shaver off.
(Dia. D)
*We recommend that you use your new
shaver daily for up to three weeks to
allow time for your hair and skin to
become accustomed to the new shaving
system.**
■ Ensure your skin is dry and free of oils.
■ Wait at least 15 minutes after getting
up before shaving, to ensure your face
is free of puffiness that may be present
from sleeping.
■ Always hold the shaver at a right angle
to the skin so the screens are touching
the skin with equal pressure.
■ Stretch skin with the free hand so hairs
stand upright, making it easier for them
to enter the cutting chamber.
■ Shave with short, circular strokes. The
use of short, circular motions in stubborn
areas may obtain a closer shave,
especially along the neck and chin line.
■ Do not press hard against the skin in
order to avoid damage to the screens.
When your rechargeable shaver reaches the end
of its useful life, the batteries must be removed
from the shaver and recycled or disposed of
properly in accordance with your state and local
requirements. If this is not required by law, you
may elect to dispose of the shaver with the
batteries.
This device uses one of the following types of
rechargeable batteries: nickel metal hydride
(NiMH), nickel cadmium (Ni-Cd) or Lithium
Ion (Li-Ion) (see included battery for indication
of type).
CAUTION: ALL RECHARGEABLE BATTERIES
MUST BE RECYCLED OR DISPOSED OF IN
ACCORDANCE WITH APPLICABLE STATE AND
LOCAL REGULATIONS. DO NOT PUT IN FIRE
OR MUTILATE, AS THE BATTERY MAY BURST
OR RELEASE TOXIC MATERIALS. DO NOT
SHORT-CIRCUIT, AS THIS MAY CAUSE BURNS.
To Remove the Rechargeable Battery:
1. Remove phillips head screw from lower back
panel of shaver.
2. Pry the back panel off the shaver releasing
the snap fits.
3. Snip the battery wires and remove the
batteries.
4. Dispose of batteries properly.
■ Never drop or insert any object into any
of the appliance’s openings.
■ Do not wrap the cord around the
appliance.
■ Do not use outdoors or operate where
aerosol (spray) products are being used
or where oxygen is being administered.
■ Do not use an extension cord or a
voltage converter with this appliance.
■ Do not use outdoors or operate where
aerosol (spray) products are being used
or where oxygen is being administered.
■ Always attach the plug to the appliance,
then to outlet. To disconnect, turn all
controls to OFF, then remove plug from
outlet.
■ Detach removable power cords from
appliance for storage.
■ Always pull on cord plug to unplug from
wall socket. Never pull on electric cord.
■ Do not plug or unplug this appliance
when your hands are wet.
■ Do not use this appliance with a
damaged or broken head or cutters, as
facial injury may occur.
■ Always store this appliance and cord in
a moisture-free area. Do not store it in
temperatures exceeding 140°F (60°C).
■ Detach removable power cords from
appliance for storage.
■ Shavers, including the trimmer, are for
use on facial hair only. They should not
be used for shaving the hair on your
head or any other part of your body.
■ For additional protection the installation
of a residual current device (RDC) with
a rated residual operating current not
exceeding 30mA is advisable. Ask an
electrician for advice (Argentina/Chile).
When using an electrical appliance, basic
precautions should always be observed,
including the following. Read all instruc-
tions before using this shaver.
DANGER
To reduce the risk of electric shock:
■ Except when charging, always unplug
this appliance from the electrical outlet
immediately after using.
■ Do not use while bathing or in the
shower.
■ Do not place or store this appliance
where it can fall or be pulled into a tub
or sink.
■ Do not place or drop into water or other
liquid.
■ Detach the appliance from the power
supply cord before cleaning.
■ Do not reach for an appliance that has
fallen into water. Unplug it immediately.
■ Use only when the shaver is in dry
condition.
■ Do not submerge in water.
WARNING
To reduce the risk of burns, fire,
electric shock, or injury to persons:
■ An appliance should never be left
unattended when it’s plugged in, except
when charging a rechargeable appliance.
■ Close supervision is necessary when
this appliance is used by, on, or near
children, or individuals with special
needs or certain disabilities.
■ Children should be supervised to ensure
they do not play with the appliance.
■ Use this appliance only for its intended
use as described in this manual. Do not
use attachments not recommended by
the manufacturer.
■ Suitable for cleaning under an open
water tap.
■ Detach the hand-held part from the
supply cord before cleaning in water.
■ Never operate this appliance if it has a
damaged cord or plug, if it is not working
properly, if it has been dropped or
damaged, of if it has been dropped into
water. Return the appliance to a service
center for examination and repair.
Note: If the power cord is damaged, it
must be replaced by personnel or
an authorized service center in Latin
America.
■ The appliance must only be used with
the power supply unit supplied with the
appliance.
■ Class III devices must establish that
they must only be supplied at a very
low safety voltage corresponding to that
marked on the device.
■ For washable models having supports or
bases, they must be installed so that they
can not fall into the water.
■ Keep the cord away from heated
surfaces.
Use and Care Guide
IMPORTANT SAFETY
INSTRUCTIONS
Guarantee - See insert
® Registered Trademark of Spectrum
Brands, Inc.
© 2018 Spectrum Brands, Inc.
11/18 Job#24521-00 T22-7000759-A
Dist. by: Spectrum Brands, Inc.,
Middleton, WI 53562
Designed in USA
MADE IN CHINA
HF9000:
Electrical Characteristics:
100-240V~ 50/60Hz 200mA
SAVE THESE INSTRUCTIONS
CAUTION: This product
is not suitable for use
in bath or shower.
It is recommended that you use your new
shaver daily for up to two weeks to allow
time for your beard and skin to become
accustomed to the new shaving system.
Your Remington Sensitive Foil shaver has
been designed to help reduce irritation
and ingrowing hairs for men who experi-
ence these conditions when shaving. The
lifting combs at both edges of the cutting
head help lift flat lying, longer hairs and
feed them into the cutters. The shaver is
designed to cut hairs at or slightly above
the skin surface to help prevent ingrown
hairs. For best results, it is recommended
to use the shaver daily or every other
day to maintain hair length and to reduce
ingrowing hairs.
Charging
Shave
Trim
Shaving Tips Cleaning & Care
Battery Removal
1. Shaving foils
2. Trimmer
3. On/off switch
4. Hair pocket
5. Pop-up trimmer
6. Foil assembly release button
7. Charging indicator.
8. Charging connector. Includes USB cable
(not shown)
Replacements
Getting Started
The blades are washable
under a running tap.
1
8
2
63
5
4
7
Charging Indicator
Charging Level Indicator
Charging LED flashes slowly
Low charge LED flashes quickly
Full charge LED comes on for 5 minutes then goes off

HF9000
NOTE: **When cleaning your shaver,
make sure the shaver is turned off and
disconnected from the power cord.**
For optimal shaver performance, clean
your shaver after each use.
■ Do not remove or replace head
assembly while shaver is running as it
may cause damage to the unit’s screens
and cutters.
■ To clean the external surfaces of the
shaver, use a damp cloth. Do not use
strong detergents or other chemicals.
■ To dry, wipe the surface of the shaver
with a dry towel. Do not use a hair dryer
or heater to dry the shaver.
■ The shaver should not be used until it
has dried.
■ Lubricate each cutter with household oil.
■ This shaver has no user serviceable
parts.
Daily Cleaning:
1. Grasp the sides of the cutter assembly
and pull away from the shaver body.
2. Tap the stubble from the foils and
cutters.
3. Replace the hairpocket assembly.
Monthly Cleaning:
1. Grasp the sides of the cutter assembly
and pull away from the shaver body.
2. Tap the stubble from the foils and
cutters.
3. Use the cleaning brush to delicately
sweep any loose hairs from the cutters
and trimmer.
4. After cleaning, replace
the hairpocket
assembly.
Replacing the Foils & Cutters
To ensure the continued highest quality
performance from your shaver, we recom-
mend that foils and cutters are replaced
regularly.
Signs that your foils and cutters need
replacing:
■ Irritation: As foils get worn, you may
experience skin irritation.
■ Pulling: As the cutters wear, your shave
may not feel as close and you may feel
your cutter pulling your hair.
■ Wear through: You may notice that the
cutters have worn through the foils.
To Replace the Foil
1. Grasp the foil carrier grips on the sides
of the shaver and pull up to remove the
foils. Discard the used foils.
2. Snap a new foil carrier in place.
To Replace the Cutters
1. Remove the foil carrier.
2. Depress cutter and rotate it 90°
counterclockwise and lift off. Do not lose
spring.
3. Place new cutter on oscillator tip,
depress and rotate 90° counterclockwise.
NOTE: Do not press on the cutter ends as
this may cause damage.
Note: It is recommended to fully charge
your appliance before using for the first
time. Please refer to the charge times
shown in this book.
1. Connect the cord to the shaver and then
to the electrical outlet. The charging
indicator light will glow green.
2. Charge your new shaver for 2 hours
before its first use. This first charge is
important to the shaver’s battery life.
■ Ensure the product is switched off.
■ Connect the adaptor to the product and
then to the mains.
■ Run time from fully charged is up to 60
minutes.
Note: To preserve the life of your batteries,
let them run out every 6 months then
fully charge.
1. Slide trimmer release button up to
engage trimmer.
2. Trim long, difficult hairs and side burns.
3. Close trimmer by pressing down.
Before using, read the important safety
instructions in front of the manual.
1. Begin by removing the protective head
guard from your shaver.
2. Slide the on/off button up to turn on.
(Dia. D)
3. Slide trimmer button up to engage and
use it to remove long hair first. Then
close down when finished.
(Dia. E_F)
4. Stretch the skin with your free hand so
the hairs stand upright.
5. Hold the shaving head so all screens
touch your skin simultaneously.
The independently floating screens
automatically adjust to the contours of
your face. Only apply light pressure on
the shaving head while shaving and
use short, circular strokes. (Dia. G)
6. After shaving, turn the shaver off.
(Dia. D)
*We recommend that you use your new
shaver daily for up to three weeks to
allow time for your hair and skin to
become accustomed to the new shaving
system.**
■ Ensure your skin is dry and free of oils.
■ Wait at least 15 minutes after getting
up before shaving, to ensure your face
is free of puffiness that may be present
from sleeping.
■ Always hold the shaver at a right angle
to the skin so the screens are touching
the skin with equal pressure.
■ Stretch skin with the free hand so hairs
stand upright, making it easier for them
to enter the cutting chamber.
■ Shave with short, circular strokes. The
use of short, circular motions in stubborn
areas may obtain a closer shave,
especially along the neck and chin line.
■ Do not press hard against the skin in
order to avoid damage to the screens.
When your rechargeable shaver reaches the end
of its useful life, the batteries must be removed
from the shaver and recycled or disposed of
properly in accordance with your state and local
requirements. If this is not required by law, you
may elect to dispose of the shaver with the
batteries.
This device uses one of the following types of
rechargeable batteries: nickel metal hydride
(NiMH), nickel cadmium (Ni-Cd) or Lithium
Ion (Li-Ion) (see included battery for indication
of type).
CAUTION: ALL RECHARGEABLE BATTERIES
MUST BE RECYCLED OR DISPOSED OF IN
ACCORDANCE WITH APPLICABLE STATE AND
LOCAL REGULATIONS. DO NOT PUT IN FIRE
OR MUTILATE, AS THE BATTERY MAY BURST
OR RELEASE TOXIC MATERIALS. DO NOT
SHORT-CIRCUIT, AS THIS MAY CAUSE BURNS.
To Remove the Rechargeable Battery:
1. Remove phillips head screw from lower back
panel of shaver.
2. Pry the back panel off the shaver releasing
the snap fits.
3. Snip the battery wires and remove the
batteries.
4. Dispose of batteries properly.
■ Never drop or insert any object into any
of the appliance’s openings.
■ Do not wrap the cord around the
appliance.
■ Do not use outdoors or operate where
aerosol (spray) products are being used
or where oxygen is being administered.
■ Do not use an extension cord or a
voltage converter with this appliance.
■ Do not use outdoors or operate where
aerosol (spray) products are being used
or where oxygen is being administered.
■ Always attach the plug to the appliance,
then to outlet. To disconnect, turn all
controls to OFF, then remove plug from
outlet.
■ Detach removable power cords from
appliance for storage.
■ Always pull on cord plug to unplug from
wall socket. Never pull on electric cord.
■ Do not plug or unplug this appliance
when your hands are wet.
■ Do not use this appliance with a
damaged or broken head or cutters, as
facial injury may occur.
■ Always store this appliance and cord in
a moisture-free area. Do not store it in
temperatures exceeding 140°F (60°C).
■ Detach removable power cords from
appliance for storage.
■ Shavers, including the trimmer, are for
use on facial hair only. They should not
be used for shaving the hair on your
head or any other part of your body.
■ For additional protection the installation
of a residual current device (RDC) with
a rated residual operating current not
exceeding 30mA is advisable. Ask an
electrician for advice (Argentina/Chile).
When using an electrical appliance, basic
precautions should always be observed,
including the following. Read all instruc-
tions before using this shaver.
DANGER
To reduce the risk of electric shock:
■ Except when charging, always unplug
this appliance from the electrical outlet
immediately after using.
■ Do not use while bathing or in the
shower.
■ Do not place or store this appliance
where it can fall or be pulled into a tub
or sink.
■ Do not place or drop into water or other
liquid.
■ Detach the appliance from the power
supply cord before cleaning.
■ Do not reach for an appliance that has
fallen into water. Unplug it immediately.
■ Use only when the shaver is in dry
condition.
■ Do not submerge in water.
WARNING
To reduce the risk of burns, fire,
electric shock, or injury to persons:
■ An appliance should never be left
unattended when it’s plugged in, except
when charging a rechargeable appliance.
■ Close supervision is necessary when
this appliance is used by, on, or near
children, or individuals with special
needs or certain disabilities.
■ Children should be supervised to ensure
they do not play with the appliance.
■ Use this appliance only for its intended
use as described in this manual. Do not
use attachments not recommended by
the manufacturer.
■ Suitable for cleaning under an open
water tap.
■ Detach the hand-held part from the
supply cord before cleaning in water.
■ Never operate this appliance if it has a
damaged cord or plug, if it is not working
properly, if it has been dropped or
damaged, of if it has been dropped into
water. Return the appliance to a service
center for examination and repair.
Note: If the power cord is damaged, it
must be replaced by personnel or
an authorized service center in Latin
America.
■ The appliance must only be used with
the power supply unit supplied with the
appliance.
■ Class III devices must establish that
they must only be supplied at a very
low safety voltage corresponding to that
marked on the device.
■ For washable models having supports or
bases, they must be installed so that they
can not fall into the water.
■ Keep the cord away from heated
surfaces.
Use and Care Guide
IMPORTANT SAFETY
INSTRUCTIONS
Guarantee - See insert
® Registered Trademark of Spectrum
Brands, Inc.
© 2018 Spectrum Brands, Inc.
11/18 Job#24521-00 T22-7000759-A
Dist. by: Spectrum Brands, Inc.,
Middleton, WI 53562
Designed in USA
MADE IN CHINA
HF9000:
Electrical Characteristics:
100-240V~ 50/60Hz 200mA
SAVE THESE INSTRUCTIONS
CAUTION: This product
is not suitable for use
in bath or shower.
It is recommended that you use your new
shaver daily for up to two weeks to allow
time for your beard and skin to become
accustomed to the new shaving system.
Your Remington Sensitive Foil shaver has
been designed to help reduce irritation
and ingrowing hairs for men who experi-
ence these conditions when shaving. The
lifting combs at both edges of the cutting
head help lift flat lying, longer hairs and
feed them into the cutters. The shaver is
designed to cut hairs at or slightly above
the skin surface to help prevent ingrown
hairs. For best results, it is recommended
to use the shaver daily or every other
day to maintain hair length and to reduce
ingrowing hairs.
Charging
Shave
Trim
Shaving Tips Cleaning & Care
Battery Removal
1. Shaving foils
2. Trimmer
3. On/off switch
4. Hair pocket
5. Pop-up trimmer
6. Foil assembly release button
7. Charging indicator.
8. Charging connector. Includes USB cable
(not shown)
Replacements
Getting Started
The blades are washable
under a running tap.
1
8
2
63
5
4
7
Charging Indicator
Charging Level Indicator
Charging LED flashes slowly
Low charge LED flashes quickly
Full charge LED comes on for 5 minutes then goes off

HF9000
NOTE: **When cleaning your shaver,
make sure the shaver is turned off and
disconnected from the power cord.**
For optimal shaver performance, clean
your shaver after each use.
■ Do not remove or replace head
assembly while shaver is running as it
may cause damage to the unit’s screens
and cutters.
■ To clean the external surfaces of the
shaver, use a damp cloth. Do not use
strong detergents or other chemicals.
■ To dry, wipe the surface of the shaver
with a dry towel. Do not use a hair dryer
or heater to dry the shaver.
■ The shaver should not be used until it
has dried.
■ Lubricate each cutter with household oil.
■ This shaver has no user serviceable
parts.
Daily Cleaning:
1. Grasp the sides of the cutter assembly
and pull away from the shaver body.
2. Tap the stubble from the foils and
cutters.
3. Replace the hairpocket assembly.
Monthly Cleaning:
1. Grasp the sides of the cutter assembly
and pull away from the shaver body.
2. Tap the stubble from the foils and
cutters.
3. Use the cleaning brush to delicately
sweep any loose hairs from the cutters
and trimmer.
4. After cleaning, replace
the hairpocket
assembly.
Replacing the Foils & Cutters
To ensure the continued highest quality
performance from your shaver, we recom-
mend that foils and cutters are replaced
regularly.
Signs that your foils and cutters need
replacing:
■ Irritation: As foils get worn, you may
experience skin irritation.
■ Pulling: As the cutters wear, your shave
may not feel as close and you may feel
your cutter pulling your hair.
■ Wear through: You may notice that the
cutters have worn through the foils.
To Replace the Foil
1. Grasp the foil carrier grips on the sides
of the shaver and pull up to remove the
foils. Discard the used foils.
2. Snap a new foil carrier in place.
To Replace the Cutters
1. Remove the foil carrier.
2. Depress cutter and rotate it 90°
counterclockwise and lift off. Do not lose
spring.
3. Place new cutter on oscillator tip,
depress and rotate 90° counterclockwise.
NOTE: Do not press on the cutter ends as
this may cause damage.
Note: It is recommended to fully charge
your appliance before using for the first
time. Please refer to the charge times
shown in this book.
1. Connect the cord to the shaver and then
to the electrical outlet. The charging
indicator light will glow green.
2. Charge your new shaver for 2 hours
before its first use. This first charge is
important to the shaver’s battery life.
■ Ensure the product is switched off.
■ Connect the adaptor to the product and
then to the mains.
■ Run time from fully charged is up to 60
minutes.
Note: To preserve the life of your batteries,
let them run out every 6 months then
fully charge.
1. Slide trimmer release button up to
engage trimmer.
2. Trim long, difficult hairs and side burns.
3. Close trimmer by pressing down.
Before using, read the important safety
instructions in front of the manual.
1. Begin by removing the protective head
guard from your shaver.
2. Slide the on/off button up to turn on.
(Dia. D)
3. Slide trimmer button up to engage and
use it to remove long hair first. Then
close down when finished.
(Dia. E_F)
4. Stretch the skin with your free hand so
the hairs stand upright.
5. Hold the shaving head so all screens
touch your skin simultaneously.
The independently floating screens
automatically adjust to the contours of
your face. Only apply light pressure on
the shaving head while shaving and
use short, circular strokes. (Dia. G)
6. After shaving, turn the shaver off.
(Dia. D)
*We recommend that you use your new
shaver daily for up to three weeks to
allow time for your hair and skin to
become accustomed to the new shaving
system.**
■ Ensure your skin is dry and free of oils.
■ Wait at least 15 minutes after getting
up before shaving, to ensure your face
is free of puffiness that may be present
from sleeping.
■ Always hold the shaver at a right angle
to the skin so the screens are touching
the skin with equal pressure.
■ Stretch skin with the free hand so hairs
stand upright, making it easier for them
to enter the cutting chamber.
■ Shave with short, circular strokes. The
use of short, circular motions in stubborn
areas may obtain a closer shave,
especially along the neck and chin line.
■ Do not press hard against the skin in
order to avoid damage to the screens.
When your rechargeable shaver reaches the end
of its useful life, the batteries must be removed
from the shaver and recycled or disposed of
properly in accordance with your state and local
requirements. If this is not required by law, you
may elect to dispose of the shaver with the
batteries.
This device uses one of the following types of
rechargeable batteries: nickel metal hydride
(NiMH), nickel cadmium (Ni-Cd) or Lithium
Ion (Li-Ion) (see included battery for indication
of type).
CAUTION: ALL RECHARGEABLE BATTERIES
MUST BE RECYCLED OR DISPOSED OF IN
ACCORDANCE WITH APPLICABLE STATE AND
LOCAL REGULATIONS. DO NOT PUT IN FIRE
OR MUTILATE, AS THE BATTERY MAY BURST
OR RELEASE TOXIC MATERIALS. DO NOT
SHORT-CIRCUIT, AS THIS MAY CAUSE BURNS.
To Remove the Rechargeable Battery:
1. Remove phillips head screw from lower back
panel of shaver.
2. Pry the back panel off the shaver releasing
the snap fits.
3. Snip the battery wires and remove the
batteries.
4. Dispose of batteries properly.
■ Never drop or insert any object into any
of the appliance’s openings.
■ Do not wrap the cord around the
appliance.
■ Do not use outdoors or operate where
aerosol (spray) products are being used
or where oxygen is being administered.
■ Do not use an extension cord or a
voltage converter with this appliance.
■ Do not use outdoors or operate where
aerosol (spray) products are being used
or where oxygen is being administered.
■ Always attach the plug to the appliance,
then to outlet. To disconnect, turn all
controls to OFF, then remove plug from
outlet.
■ Detach removable power cords from
appliance for storage.
■ Always pull on cord plug to unplug from
wall socket. Never pull on electric cord.
■ Do not plug or unplug this appliance
when your hands are wet.
■ Do not use this appliance with a
damaged or broken head or cutters, as
facial injury may occur.
■ Always store this appliance and cord in
a moisture-free area. Do not store it in
temperatures exceeding 140°F (60°C).
■ Detach removable power cords from
appliance for storage.
■ Shavers, including the trimmer, are for
use on facial hair only. They should not
be used for shaving the hair on your
head or any other part of your body.
■ For additional protection the installation
of a residual current device (RDC) with
a rated residual operating current not
exceeding 30mA is advisable. Ask an
electrician for advice (Argentina/Chile).
When using an electrical appliance, basic
precautions should always be observed,
including the following. Read all instruc-
tions before using this shaver.
DANGER
To reduce the risk of electric shock:
■ Except when charging, always unplug
this appliance from the electrical outlet
immediately after using.
■ Do not use while bathing or in the
shower.
■ Do not place or store this appliance
where it can fall or be pulled into a tub
or sink.
■ Do not place or drop into water or other
liquid.
■ Detach the appliance from the power
supply cord before cleaning.
■ Do not reach for an appliance that has
fallen into water. Unplug it immediately.
■ Use only when the shaver is in dry
condition.
■ Do not submerge in water.
WARNING
To reduce the risk of burns, fire,
electric shock, or injury to persons:
■ An appliance should never be left
unattended when it’s plugged in, except
when charging a rechargeable appliance.
■ Close supervision is necessary when
this appliance is used by, on, or near
children, or individuals with special
needs or certain disabilities.
■ Children should be supervised to ensure
they do not play with the appliance.
■ Use this appliance only for its intended
use as described in this manual. Do not
use attachments not recommended by
the manufacturer.
■ Suitable for cleaning under an open
water tap.
■ Detach the hand-held part from the
supply cord before cleaning in water.
■ Never operate this appliance if it has a
damaged cord or plug, if it is not working
properly, if it has been dropped or
damaged, of if it has been dropped into
water. Return the appliance to a service
center for examination and repair.
Note: If the power cord is damaged, it
must be replaced by personnel or
an authorized service center in Latin
America.
■ The appliance must only be used with
the power supply unit supplied with the
appliance.
■ Class III devices must establish that
they must only be supplied at a very
low safety voltage corresponding to that
marked on the device.
■ For washable models having supports or
bases, they must be installed so that they
can not fall into the water.
■ Keep the cord away from heated
surfaces.
Use and Care Guide
IMPORTANT SAFETY
INSTRUCTIONS
Guarantee - See insert
® Registered Trademark of Spectrum
Brands, Inc.
© 2018 Spectrum Brands, Inc.
11/18 Job#24521-00 T22-7000759-A
Dist. by: Spectrum Brands, Inc.,
Middleton, WI 53562
Designed in USA
MADE IN CHINA
HF9000:
Electrical Characteristics:
100-240V~ 50/60Hz 200mA
SAVE THESE INSTRUCTIONS
CAUTION: This product
is not suitable for use
in bath or shower.
It is recommended that you use your new
shaver daily for up to two weeks to allow
time for your beard and skin to become
accustomed to the new shaving system.
Your Remington Sensitive Foil shaver has
been designed to help reduce irritation
and ingrowing hairs for men who experi-
ence these conditions when shaving. The
lifting combs at both edges of the cutting
head help lift flat lying, longer hairs and
feed them into the cutters. The shaver is
designed to cut hairs at or slightly above
the skin surface to help prevent ingrown
hairs. For best results, it is recommended
to use the shaver daily or every other
day to maintain hair length and to reduce
ingrowing hairs.
Charging
Shave
Trim
Shaving Tips Cleaning & Care
Battery Removal
1. Shaving foils
2. Trimmer
3. On/off switch
4. Hair pocket
5. Pop-up trimmer
6. Foil assembly release button
7. Charging indicator.
8. Charging connector. Includes USB cable
(not shown)
Replacements
Getting Started
The blades are washable
under a running tap.
1
8
2
63
5
4
7
Charging Indicator
Charging Level Indicator
Charging LED flashes slowly
Low charge LED flashes quickly
Full charge LED comes on for 5 minutes then goes off

HF9000
NOTE: **When cleaning your shaver,
make sure the shaver is turned off and
disconnected from the power cord.**
For optimal shaver performance, clean
your shaver after each use.
■ Do not remove or replace head
assembly while shaver is running as it
may cause damage to the unit’s screens
and cutters.
■ To clean the external surfaces of the
shaver, use a damp cloth. Do not use
strong detergents or other chemicals.
■ To dry, wipe the surface of the shaver
with a dry towel. Do not use a hair dryer
or heater to dry the shaver.
■ The shaver should not be used until it
has dried.
■ Lubricate each cutter with household oil.
■ This shaver has no user serviceable
parts.
Daily Cleaning:
1. Grasp the sides of the cutter assembly
and pull away from the shaver body.
2. Tap the stubble from the foils and
cutters.
3. Replace the hairpocket assembly.
Monthly Cleaning:
1. Grasp the sides of the cutter assembly
and pull away from the shaver body.
2. Tap the stubble from the foils and
cutters.
3. Use the cleaning brush to delicately
sweep any loose hairs from the cutters
and trimmer.
4. After cleaning, replace
the hairpocket
assembly.
Replacing the Foils & Cutters
To ensure the continued highest quality
performance from your shaver, we recom-
mend that foils and cutters are replaced
regularly.
Signs that your foils and cutters need
replacing:
■ Irritation: As foils get worn, you may
experience skin irritation.
■ Pulling: As the cutters wear, your shave
may not feel as close and you may feel
your cutter pulling your hair.
■ Wear through: You may notice that the
cutters have worn through the foils.
To Replace the Foil
1. Grasp the foil carrier grips on the sides
of the shaver and pull up to remove the
foils. Discard the used foils.
2. Snap a new foil carrier in place.
To Replace the Cutters
1. Remove the foil carrier.
2. Depress cutter and rotate it 90°
counterclockwise and lift off. Do not lose
spring.
3. Place new cutter on oscillator tip,
depress and rotate 90° counterclockwise.
NOTE: Do not press on the cutter ends as
this may cause damage.
Note: It is recommended to fully charge
your appliance before using for the first
time. Please refer to the charge times
shown in this book.
1. Connect the cord to the shaver and then
to the electrical outlet. The charging
indicator light will glow green.
2. Charge your new shaver for 2 hours
before its first use. This first charge is
important to the shaver’s battery life.
■ Ensure the product is switched off.
■ Connect the adaptor to the product and
then to the mains.
■ Run time from fully charged is up to 60
minutes.
Note: To preserve the life of your batteries,
let them run out every 6 months then
fully charge.
1. Slide trimmer release button up to
engage trimmer.
2. Trim long, difficult hairs and side burns.
3. Close trimmer by pressing down.
Before using, read the important safety
instructions in front of the manual.
1. Begin by removing the protective head
guard from your shaver.
2. Slide the on/off button up to turn on.
(Dia. D)
3. Slide trimmer button up to engage and
use it to remove long hair first. Then
close down when finished.
(Dia. E_F)
4. Stretch the skin with your free hand so
the hairs stand upright.
5. Hold the shaving head so all screens
touch your skin simultaneously.
The independently floating screens
automatically adjust to the contours of
your face. Only apply light pressure on
the shaving head while shaving and
use short, circular strokes. (Dia. G)
6. After shaving, turn the shaver off.
(Dia. D)
*We recommend that you use your new
shaver daily for up to three weeks to
allow time for your hair and skin to
become accustomed to the new shaving
system.**
■ Ensure your skin is dry and free of oils.
■ Wait at least 15 minutes after getting
up before shaving, to ensure your face
is free of puffiness that may be present
from sleeping.
■ Always hold the shaver at a right angle
to the skin so the screens are touching
the skin with equal pressure.
■ Stretch skin with the free hand so hairs
stand upright, making it easier for them
to enter the cutting chamber.
■ Shave with short, circular strokes. The
use of short, circular motions in stubborn
areas may obtain a closer shave,
especially along the neck and chin line.
■ Do not press hard against the skin in
order to avoid damage to the screens.
When your rechargeable shaver reaches the end
of its useful life, the batteries must be removed
from the shaver and recycled or disposed of
properly in accordance with your state and local
requirements. If this is not required by law, you
may elect to dispose of the shaver with the
batteries.
This device uses one of the following types of
rechargeable batteries: nickel metal hydride
(NiMH), nickel cadmium (Ni-Cd) or Lithium
Ion (Li-Ion) (see included battery for indication
of type).
CAUTION: ALL RECHARGEABLE BATTERIES
MUST BE RECYCLED OR DISPOSED OF IN
ACCORDANCE WITH APPLICABLE STATE AND
LOCAL REGULATIONS. DO NOT PUT IN FIRE
OR MUTILATE, AS THE BATTERY MAY BURST
OR RELEASE TOXIC MATERIALS. DO NOT
SHORT-CIRCUIT, AS THIS MAY CAUSE BURNS.
To Remove the Rechargeable Battery:
1. Remove phillips head screw from lower back
panel of shaver.
2. Pry the back panel off the shaver releasing
the snap fits.
3. Snip the battery wires and remove the
batteries.
4. Dispose of batteries properly.
■ Never drop or insert any object into any
of the appliance’s openings.
■ Do not wrap the cord around the
appliance.
■ Do not use outdoors or operate where
aerosol (spray) products are being used
or where oxygen is being administered.
■ Do not use an extension cord or a
voltage converter with this appliance.
■ Do not use outdoors or operate where
aerosol (spray) products are being used
or where oxygen is being administered.
■ Always attach the plug to the appliance,
then to outlet. To disconnect, turn all
controls to OFF, then remove plug from
outlet.
■ Detach removable power cords from
appliance for storage.
■ Always pull on cord plug to unplug from
wall socket. Never pull on electric cord.
■ Do not plug or unplug this appliance
when your hands are wet.
■ Do not use this appliance with a
damaged or broken head or cutters, as
facial injury may occur.
■ Always store this appliance and cord in
a moisture-free area. Do not store it in
temperatures exceeding 140°F (60°C).
■ Detach removable power cords from
appliance for storage.
■ Shavers, including the trimmer, are for
use on facial hair only. They should not
be used for shaving the hair on your
head or any other part of your body.
■ For additional protection the installation
of a residual current device (RDC) with
a rated residual operating current not
exceeding 30mA is advisable. Ask an
electrician for advice (Argentina/Chile).
When using an electrical appliance, basic
precautions should always be observed,
including the following. Read all instruc-
tions before using this shaver.
DANGER
To reduce the risk of electric shock:
■ Except when charging, always unplug
this appliance from the electrical outlet
immediately after using.
■ Do not use while bathing or in the
shower.
■ Do not place or store this appliance
where it can fall or be pulled into a tub
or sink.
■ Do not place or drop into water or other
liquid.
■ Detach the appliance from the power
supply cord before cleaning.
■ Do not reach for an appliance that has
fallen into water. Unplug it immediately.
■ Use only when the shaver is in dry
condition.
■ Do not submerge in water.
WARNING
To reduce the risk of burns, fire,
electric shock, or injury to persons:
■ An appliance should never be left
unattended when it’s plugged in, except
when charging a rechargeable appliance.
■ Close supervision is necessary when
this appliance is used by, on, or near
children, or individuals with special
needs or certain disabilities.
■ Children should be supervised to ensure
they do not play with the appliance.
■ Use this appliance only for its intended
use as described in this manual. Do not
use attachments not recommended by
the manufacturer.
■ Suitable for cleaning under an open
water tap.
■ Detach the hand-held part from the
supply cord before cleaning in water.
■ Never operate this appliance if it has a
damaged cord or plug, if it is not working
properly, if it has been dropped or
damaged, of if it has been dropped into
water. Return the appliance to a service
center for examination and repair.
Note: If the power cord is damaged, it
must be replaced by personnel or
an authorized service center in Latin
America.
■ The appliance must only be used with
the power supply unit supplied with the
appliance.
■ Class III devices must establish that
they must only be supplied at a very
low safety voltage corresponding to that
marked on the device.
■ For washable models having supports or
bases, they must be installed so that they
can not fall into the water.
■ Keep the cord away from heated
surfaces.
Use and Care Guide
IMPORTANT SAFETY
INSTRUCTIONS
Guarantee - See insert
® Registered Trademark of Spectrum
Brands, Inc.
© 2018 Spectrum Brands, Inc.
11/18 Job#24521-00 T22-7000759-A
Dist. by: Spectrum Brands, Inc.,
Middleton, WI 53562
Designed in USA
MADE IN CHINA
HF9000:
Electrical Characteristics:
100-240V~ 50/60Hz 200mA
SAVE THESE INSTRUCTIONS
CAUTION: This product
is not suitable for use
in bath or shower.
It is recommended that you use your new
shaver daily for up to two weeks to allow
time for your beard and skin to become
accustomed to the new shaving system.
Your Remington Sensitive Foil shaver has
been designed to help reduce irritation
and ingrowing hairs for men who experi-
ence these conditions when shaving. The
lifting combs at both edges of the cutting
head help lift flat lying, longer hairs and
feed them into the cutters. The shaver is
designed to cut hairs at or slightly above
the skin surface to help prevent ingrown
hairs. For best results, it is recommended
to use the shaver daily or every other
day to maintain hair length and to reduce
ingrowing hairs.
Charging
Shave
Trim
Shaving Tips Cleaning & Care
Battery Removal
1. Shaving foils
2. Trimmer
3. On/off switch
4. Hair pocket
5. Pop-up trimmer
6. Foil assembly release button
7. Charging indicator.
8. Charging connector. Includes USB cable
(not shown)
Replacements
Getting Started
The blades are washable
under a running tap.
1
8
2
63
5
4
7
Charging Indicator
Charging Level Indicator
Charging LED flashes slowly
Low charge LED flashes quickly
Full charge LED comes on for 5 minutes then goes off

HF9000
NOTE: **When cleaning your shaver,
make sure the shaver is turned off and
disconnected from the power cord.**
For optimal shaver performance, clean
your shaver after each use.
■ Do not remove or replace head
assembly while shaver is running as it
may cause damage to the unit’s screens
and cutters.
■ To clean the external surfaces of the
shaver, use a damp cloth. Do not use
strong detergents or other chemicals.
■ To dry, wipe the surface of the shaver
with a dry towel. Do not use a hair dryer
or heater to dry the shaver.
■ The shaver should not be used until it
has dried.
■ Lubricate each cutter with household oil.
■ This shaver has no user serviceable
parts.
Daily Cleaning:
1. Grasp the sides of the cutter assembly
and pull away from the shaver body.
2. Tap the stubble from the foils and
cutters.
3. Replace the hairpocket assembly.
Monthly Cleaning:
1. Grasp the sides of the cutter assembly
and pull away from the shaver body.
2. Tap the stubble from the foils and
cutters.
3. Use the cleaning brush to delicately
sweep any loose hairs from the cutters
and trimmer.
4. After cleaning, replace
the hairpocket
assembly.
Replacing the Foils & Cutters
To ensure the continued highest quality
performance from your shaver, we recom-
mend that foils and cutters are replaced
regularly.
Signs that your foils and cutters need
replacing:
■ Irritation: As foils get worn, you may
experience skin irritation.
■ Pulling: As the cutters wear, your shave
may not feel as close and you may feel
your cutter pulling your hair.
■ Wear through: You may notice that the
cutters have worn through the foils.
To Replace the Foil
1. Grasp the foil carrier grips on the sides
of the shaver and pull up to remove the
foils. Discard the used foils.
2. Snap a new foil carrier in place.
To Replace the Cutters
1. Remove the foil carrier.
2. Depress cutter and rotate it 90°
counterclockwise and lift off. Do not lose
spring.
3. Place new cutter on oscillator tip,
depress and rotate 90° counterclockwise.
NOTE: Do not press on the cutter ends as
this may cause damage.
Note: It is recommended to fully charge
your appliance before using for the first
time. Please refer to the charge times
shown in this book.
1. Connect the cord to the shaver and then
to the electrical outlet. The charging
indicator light will glow green.
2. Charge your new shaver for 2 hours
before its first use. This first charge is
important to the shaver’s battery life.
■ Ensure the product is switched off.
■ Connect the adaptor to the product and
then to the mains.
■ Run time from fully charged is up to 60
minutes.
Note: To preserve the life of your batteries,
let them run out every 6 months then
fully charge.
1. Slide trimmer release button up to
engage trimmer.
2. Trim long, difficult hairs and side burns.
3. Close trimmer by pressing down.
Before using, read the important safety
instructions in front of the manual.
1. Begin by removing the protective head
guard from your shaver.
2. Slide the on/off button up to turn on.
(Dia. D)
3. Slide trimmer button up to engage and
use it to remove long hair first. Then
close down when finished.
(Dia. E_F)
4. Stretch the skin with your free hand so
the hairs stand upright.
5. Hold the shaving head so all screens
touch your skin simultaneously.
The independently floating screens
automatically adjust to the contours of
your face. Only apply light pressure on
the shaving head while shaving and
use short, circular strokes. (Dia. G)
6. After shaving, turn the shaver off.
(Dia. D)
*We recommend that you use your new
shaver daily for up to three weeks to
allow time for your hair and skin to
become accustomed to the new shaving
system.**
■ Ensure your skin is dry and free of oils.
■ Wait at least 15 minutes after getting
up before shaving, to ensure your face
is free of puffiness that may be present
from sleeping.
■ Always hold the shaver at a right angle
to the skin so the screens are touching
the skin with equal pressure.
■ Stretch skin with the free hand so hairs
stand upright, making it easier for them
to enter the cutting chamber.
■ Shave with short, circular strokes. The
use of short, circular motions in stubborn
areas may obtain a closer shave,
especially along the neck and chin line.
■ Do not press hard against the skin in
order to avoid damage to the screens.
When your rechargeable shaver reaches the end
of its useful life, the batteries must be removed
from the shaver and recycled or disposed of
properly in accordance with your state and local
requirements. If this is not required by law, you
may elect to dispose of the shaver with the
batteries.
This device uses one of the following types of
rechargeable batteries: nickel metal hydride
(NiMH), nickel cadmium (Ni-Cd) or Lithium
Ion (Li-Ion) (see included battery for indication
of type).
CAUTION: ALL RECHARGEABLE BATTERIES
MUST BE RECYCLED OR DISPOSED OF IN
ACCORDANCE WITH APPLICABLE STATE AND
LOCAL REGULATIONS. DO NOT PUT IN FIRE
OR MUTILATE, AS THE BATTERY MAY BURST
OR RELEASE TOXIC MATERIALS. DO NOT
SHORT-CIRCUIT, AS THIS MAY CAUSE BURNS.
To Remove the Rechargeable Battery:
1. Remove phillips head screw from lower back
panel of shaver.
2. Pry the back panel off the shaver releasing
the snap fits.
3. Snip the battery wires and remove the
batteries.
4. Dispose of batteries properly.
■ Never drop or insert any object into any
of the appliance’s openings.
■ Do not wrap the cord around the
appliance.
■ Do not use outdoors or operate where
aerosol (spray) products are being used
or where oxygen is being administered.
■ Do not use an extension cord or a
voltage converter with this appliance.
■ Do not use outdoors or operate where
aerosol (spray) products are being used
or where oxygen is being administered.
■ Always attach the plug to the appliance,
then to outlet. To disconnect, turn all
controls to OFF, then remove plug from
outlet.
■ Detach removable power cords from
appliance for storage.
■ Always pull on cord plug to unplug from
wall socket. Never pull on electric cord.
■ Do not plug or unplug this appliance
when your hands are wet.
■ Do not use this appliance with a
damaged or broken head or cutters, as
facial injury may occur.
■ Always store this appliance and cord in
a moisture-free area. Do not store it in
temperatures exceeding 140°F (60°C).
■ Detach removable power cords from
appliance for storage.
■ Shavers, including the trimmer, are for
use on facial hair only. They should not
be used for shaving the hair on your
head or any other part of your body.
■ For additional protection the installation
of a residual current device (RDC) with
a rated residual operating current not
exceeding 30mA is advisable. Ask an
electrician for advice (Argentina/Chile).
When using an electrical appliance, basic
precautions should always be observed,
including the following. Read all instruc-
tions before using this shaver.
DANGER
To reduce the risk of electric shock:
■ Except when charging, always unplug
this appliance from the electrical outlet
immediately after using.
■ Do not use while bathing or in the
shower.
■ Do not place or store this appliance
where it can fall or be pulled into a tub
or sink.
■ Do not place or drop into water or other
liquid.
■ Detach the appliance from the power
supply cord before cleaning.
■ Do not reach for an appliance that has
fallen into water. Unplug it immediately.
■ Use only when the shaver is in dry
condition.
■ Do not submerge in water.
WARNING
To reduce the risk of burns, fire,
electric shock, or injury to persons:
■ An appliance should never be left
unattended when it’s plugged in, except
when charging a rechargeable appliance.
■ Close supervision is necessary when
this appliance is used by, on, or near
children, or individuals with special
needs or certain disabilities.
■ Children should be supervised to ensure
they do not play with the appliance.
■ Use this appliance only for its intended
use as described in this manual. Do not
use attachments not recommended by
the manufacturer.
■ Suitable for cleaning under an open
water tap.
■ Detach the hand-held part from the
supply cord before cleaning in water.
■ Never operate this appliance if it has a
damaged cord or plug, if it is not working
properly, if it has been dropped or
damaged, of if it has been dropped into
water. Return the appliance to a service
center for examination and repair.
Note: If the power cord is damaged, it
must be replaced by personnel or
an authorized service center in Latin
America.
■ The appliance must only be used with
the power supply unit supplied with the
appliance.
■ Class III devices must establish that
they must only be supplied at a very
low safety voltage corresponding to that
marked on the device.
■ For washable models having supports or
bases, they must be installed so that they
can not fall into the water.
■ Keep the cord away from heated
surfaces.
Use and Care Guide
IMPORTANT SAFETY
INSTRUCTIONS
Guarantee - See insert
® Registered Trademark of Spectrum
Brands, Inc.
© 2018 Spectrum Brands, Inc.
11/18 Job#24521-00 T22-7000759-A
Dist. by: Spectrum Brands, Inc.,
Middleton, WI 53562
Designed in USA
MADE IN CHINA
HF9000:
Electrical Characteristics:
100-240V~ 50/60Hz 200mA
SAVE THESE INSTRUCTIONS
CAUTION: This product
is not suitable for use
in bath or shower.
It is recommended that you use your new
shaver daily for up to two weeks to allow
time for your beard and skin to become
accustomed to the new shaving system.
Your Remington Sensitive Foil shaver has
been designed to help reduce irritation
and ingrowing hairs for men who experi-
ence these conditions when shaving. The
lifting combs at both edges of the cutting
head help lift flat lying, longer hairs and
feed them into the cutters. The shaver is
designed to cut hairs at or slightly above
the skin surface to help prevent ingrown
hairs. For best results, it is recommended
to use the shaver daily or every other
day to maintain hair length and to reduce
ingrowing hairs.
Charging
Shave
Trim
Shaving Tips Cleaning & Care
Battery Removal
1. Shaving foils
2. Trimmer
3. On/off switch
4. Hair pocket
5. Pop-up trimmer
6. Foil assembly release button
7. Charging indicator.
8. Charging connector. Includes USB cable
(not shown)
Replacements
Getting Started
The blades are washable
under a running tap.
1
8
2
63
5
4
7
Charging Indicator
Charging Level Indicator
Charging LED flashes slowly
Low charge LED flashes quickly
Full charge LED comes on for 5 minutes then goes off