Remocon HCD900 User manual

1
REMOCON Duplicator HCD900(Version 3001.14)
Operation manual
HCD-900 Accessories
HCD-900 Console 6Micro USD Duplicating & Updating Cable
(Attached)
AC/DC Power Adaptor(attached) 6P connector Duplicating Cable (Optional)
Frequency Tuning Bar (Optional)

2
1. Plug in the power adapter into power outlet and push power switch on.(Fig.1)
Caution: Do not put the duplicator on the metal surface while operating, and keep
interference(mobile phone, router....) away while operating.
2. LCD screen displays Main Menu.(Fig. 2)
Fig. 1 Fig.2
Remark: Press &to move highlight to desired mode and press Confirm. If you
would like to return to MAIN MENU after entering, press Cancel .
3. Function instruction
3-1. Frequency Meter (Fig. 3)
3-1-1. Func.: Read transmitting frequency from remote controls.
3-1-2. Hold the remote control one hand near the Test Area of HCD900, and press
any button of the remote control. The “Measuring”keeps flashing and "signal
strength bar" changes while reading the frequency; Slightly move the
position of the remote control until you get the longest signal bar to ensure
you can get most correct frequency.(Fig. 4)
Fig. 3 Fig. 4
REMOCON
Version 3001.13
MAIN MENU
Frequency Meter
FixedCode Duplicate
HoppingCode Duplicate
REMOCON Read Back
Code Checking
Make Hopping
Setting
Frequency Meter
0.0Mhz
MAIN MENU
Frequency Meter
FixedCode Duplicate
HoppingCode Duplicate
REMOCON Read Back
Code Checking
Make Hopping
Setting
Fn
Confirm
Cancel
Test
Area
Frequency Meter
Measuring
433.7Mhz
11111111111111111111
Power swith

3
3-1-3. If there are some high frequencies around you to interfere the reading of the
frequency, you can change your Meter to low frequency Mode(LCD displays
"LF" on screen, Fig.5) by pressing "Fn" and "Confirm" at the same time.
Under Low frequency mode, it will only detect frequency under 600MHz.
Fig. 5
3-2. Fixed Code Duplicate: No.1 to No. 5 are for frequency band 1, and No. 6 to
No.10 are for frequency band 2(for dual frequency remotes).
3-2-1. Func.: Read and duplicate fixed
code from original remote control
into REMOCON remote control. It
provides 10 channels for
programming. (Fig. 6)
3-2-2. Places original transmitter near the
Test Area of HCD900.
Fig. 6
3-2-3. Press and holding 1st button of
original remote control, LCD screen
displays “Processing”. Release the
button when you hear a beep. Now
the frequency and type of remote of
original remote is shown above the
channels, and the code of the 1st
button of original remote has been
read successfully.(Fig. 7)
3-2-4. Repeat step 3-2-3. until all buttons
of original remote control have
been read by HCD900.(Fig. 8)
[Note: for dual frequency remotes
RMC-552, RMC-556 & RMC-558: channel
1 to 5 are for buttons 1 to 5 when the
switch position is “Up”, and channels 6 to
10 are for buttons 1 to 5 when the switch
position is “Down”; for RMC-558C:
opposite to above]
FixedCode Duplicate
12 3 4 5 6 7 8 9 10
10 key spaces remain
Ready
FixedCode Duplicate
433.9 B10 Type
1 23 4 5 6 7 8 9 10
1 9 key spaces remain
Processing
Ready
FixedCode Duplicate
433.9
1 2 3 4 56 7 8 9 10
1111
6 key spaces remain
Ready
Frequency Meter
LF
0.0Mhz
Fig. 7
Fig. 8

4
3-2-5. (Only for dual frequency remote)
After all keys of 2 remotes with
different frequencies has been read
by HCD-900, press & to move
highlight to channel 1 ~ 5 and
channel 6 ~ 10 and to choose the
right frequency bands on
REMOCON remote by pressing
& (Fig. 9)
Fig. 9
3-2-6. Press Confirm to enter duplicating
mode, the LCD displays as Fig. 10
3-2-7. Connects B or C type REMOCON remote
control to HCD900 by using attached
duplicating cable.
Fig. 10
3-2-8. Press Confirm to program the code
into REMOCON remote control.
LCD displays duplication result as
Programming Success or
Programming Failure.(Fig. 11)
Notice: if the original remote belongs to C type
but you connect a B type REMOCON
remote, the LCD screen will display
"Please Use C Remote" and please connect
a C type REMOCON remote and retry.Fig.11
3-3. Hopping Code Duplicate:(Fig. 12)
3-3-1. Func.: Read and duplicate hopping
code from original remote controls
into REMOCON remote controls.
Fig. 12
Attention: Some brands of hopping code remote controls were required to input
“seed code”before going to next step. To input “seed code”, please follow
FixedCode Duplicate
433.9
1 2 3 4 56 7 8 9 10
1111
6 key spaces remain
Please Connect Remote
FixedCode Duplicate
1 2 3 4 56 7 8 9 10
1111
6 key spaces remain
Programming success
HoppingCode Duplicate
12 3 4 5 6 7 8 9 10
10 key spaces remain
Please enter 1st code
FixedCode Duplicate
433.9
1 2 3 4 5 6 7 8 9 10
11112222
6 key spaces remain
Ready

5
the steps below:
a. Touch Fn & simultaneously.
b. LCD displays “Receiving seed code”.(Fig. 13)
c. You can probably find the seed code button on the rear of original
remote control. It might be hidden in an eyelet. If so, you need a
acicular object to poke it for transmitting the seed code.
d. The LCD displays (Fig. 14) when the “seed code”was received.
Fig. 13 Fig. 14
3-3-2. Place the original remote control
near the Test Area of HCD900.
3-3-3. Press and holding 1st button of
original remote control, LCD
displays a serial number(Fig. 15).
(Each remote control has its own
series number).
Fig. 15
3-3-4 Press and holding 1st button of
original remote control again. The
LCD displays as Fig. 16. It will
create a new serial number
automatically for the REMOCON
remotes and you can also change
it to whatever number you need.
The number on the bottom right
corner is the serial number of the
original remote.
Notice: Don't set up the same serial number with the original remote; Otherwise, you will
have problem using 2 remotes at the same time.
3-3-5. Press Confirm , the LCD displays as
Fig. 17. Now the 1st button has been
stored successfully
HoppingCode Duplicate
12 3 4 5 6 7 8 9 10
10 key spaces remain
Receiving seed code
HoppingCode Duplicate
12 3 4 5 6 7 8 9 10
10 key spaces remain
HCS 10x 20x 30x
Please enter 1st code
HoppingCode Duplicate
433.9
12 3 4 5 6 7 8 9 10
10 key spaces remain
HCS 10x 20x 30x
02 00024E68 7606A080
Please enter 2nd code
HoppingCode Duplicate
433.9
12 3 4 5 6 7 8 9 10
10 key spaces remain
Serial Number Setting
00242D3
BFT 00024E68
HoppingCode Duplicate
433.9
123 4 5 6 7 8 9 10
1 9 key spaces remain
Please enter 1stcode
Fig. 16

6
fig.17
3-3-6. Press and holding 2nd button of original
remote control, LCD displays as (Fig. 18)
3-3-7. Repeat step 3-3-6. to store other buttons
of original remote control.
Fig. 18
3-3-8. If the frequency that HCD-900 detects(LCD displays on the upper left corner) is not
correct, you can revise the frequency for one
button or all buttons as below:
3-3-8-1. Move the highlight to the channel that
you would like to revise the frequency,
and then press Fn and at same time.
(Fig. 19)
Fig.19
3-3-8-2. Press and to move the "！" to
different position above the frequency
and press and to adjust the
value of the frequency.(Fig. 20)
Fig. 20
3-3-8-3. Move "！" to the last position and you
can select to revise frequency for only
one button(the channel where the highlight
is) or all buttons.(Fig. 21)
Fig. 21
3-3-8-4. Press Confirm then the revision of frequency
is done.
Attention: You can also revise the frequency by the same way in FixedCode
Duplicate Mode.
3-3-9. Connect the H series or BHS/CHM/CHML new series REMOCON remote control to
HCD900 by using attached duplicating cable.
Notice: if the original rolling code remote uses new IC format that H3/BHS/CHM does not
support, the LCD screen will display "Please Use CHMLRemote" and please connect a H4
HoppingCode Duplicate
433.9
1234 5 6 7 8 9 10
11 8 key spaces remain
Please enter 1stcode
HoppingCode Duplicate
433.9
1234 5 6 7 8 9 10
11 8 key spaces remain
！
ALL 433.9 MHz
HoppingCode Duplicate
433.9
1234 5 6 7 8 9 10
11 8 key spaces remain
！
ALL 432.9 MHz
HoppingCode Duplicate
433.9
1234 5 6 7 8 9 10
11 8 key spaces remain
！
One 432.9 MHz

7
IC remote or CHML REMOCON remote and retry.
3-3-10. Press Confirm to program the code into REMOCON remote control.
3-3-11. LCD displays duplicating result as
Programming Success or
Programming Failure.(Fig. 22)
3-4. REMOCON Read Back (For Fixed Code remote)
3-4-1 Func.: To read the code from REMOCON remote control, and reduplicate the
code into other REMOCON remote controls.
3-4-2. Be sure to connect REMOCON
remote control(existing code) to
HCD900 by using attached
duplicating cable before entering
“REMOCON Read Back”mode.
(Fig. 23)
3-4-3. Move highlight to “REMOCON
Read Back”mode, press Confirm
to start reading. The LCD displays
as Fig. 24.
Fig. 24
3-4-4. Replace the remote control by a new REMOCON remote control and touch
Confirm. LCD displays duplication result as Programming Success or Programming
Failure.
3-5. Code Checking(Fig. 25)
3-5-1. Func.: There are 2 functions in
this mode: First is to verify
whether the fixed code
duplication has been done
successfully or not; Second is to
identify your existing remote
control is fixed code or hopping
code.
HoppingCode Duplicate
1234 5 6 7 8 9 10
11 8 key spaces remain
Programming success
Please enter 1stcode
MAIN MENU
Frequency Meter
FixedCode Duplicate
HoppingCode Duplicate
REMOCON Read Back
Code Checking
Remote Report
FixedCode Duplicate
1 2 3 4 56 7 8 9 10
1111
6 key spaces remain
Ready
Code Checking
Please Enter 1st Code
Press cancel To Exit
Fig. 23
Fig. 25
Fig. 22

8
3-5-2. To verify if the duplication has
been done successfully, press
1st button of original fixed code
remote control till you hear a
beep.
3-5-3 The LCD appears “Processing”
and goes to Fig. 26.
3-5-4. Press 1st button of the duplicated
remote, HCD900 starts to check
the contrast, and then shows the
similarity percentage.(Fig. 27)
Fig. 27 3-5-5. Follow steps 3-5-2, 3-5-3 &3-5-4 to
verify other buttons.
Attention: The qualified duplication requires at least 90% similarity.
3-5-6. To identify whether the remote control is fixed code or hopping code, press
1st button of the remote control. (Fig. 25)
3-5-7. The LCD appears “Processing”and goes to Fig. 26.
3-5-8. Press the same button again. HCD900 starts to check the contrast, and then
shows the similarity percentage.(Fig. 27)
3-5-9. Hopping code remote control will show 0.0 percent matched.
3-6. Make Hopping(for Hopping Code remote)
3-6-1. Func.: Create a duplicate remote without the existing of original rolling code
remote control. (This function can only be used to create original remotes with
HCSxxx IC format and original remotes without seed code, if you would like to
create these 2 kinds of remotes, please use HCD-900line)
3-6-2. Press and to choose PAGE
or 1 so that you can select brand
"Page by page" or" brand by
brand". (Fig. 28)
3-6-3. Press to enter the Reference
Number Setting.
Press and to set up the
distributor code. (Only need to
set up for certain brands) (Fig. 29)
Code Checking
Please Enter 2nd Code
Press cancel To Exit
Code Checking
Please Enter 1st Code
99.2
Percent Matched
Press cancel To Exit
Make Hopping
PAGE 1
NiceSmile
Neo
GiBiDi
FADIN 00
Make Hopping
FADIN 01
Fig. 26
Fig. 28
Fig. 29

9
3-6-4. Press Confirm to enter the
Serial Number Setting.
Press and to set up the
serial number. (Fig. 30)
Fig. 30
3-6-5. Press Confirm to ready to copy.
(Fig. 31)
Notice: If you would like copy to a
CHM or CHML remote, please ensure to
set up the frequency first by pressing Fn
and simultaneously.
Connect H series or BHS/CHM
/CHML REMOCON remote control
to HCD-900 by using attached
duplicating cable.
3-6-6. Press Confirm to program the
code into REMOCON remote
control. LCD displays duplication
result as Programming Success or
Programming Failure.(Fig. 32)
Fig. 32
3-7. Setting
3-7-1. Func.: See relative information or change the setting.
3-7-2. You can see the version number
and production serial number
of your HCD-900 after entering
setting mode.(Fig. 33)
.
Fig. 33
3-7-3. Press and you will enter the
setting page as Fig. 34. Press
and to select the project and
press to change the parameter
Fig. 34
Make Hopping
Serial Number Setting
0000001
FADIN 01
HoppingCode Duplicate
12 3 4 5 6 7 8 9 10
2 4 9 D D 6 B F D D
0 key spaces remain
Press Confirm To Copy
HoppingCode Duplicate
12 3 4 5 6 7 8 9 10
2 4 9 D D 6 B F D D
0 key spaces remain
Programming Success
Press Confirm To Copy
Setting
Version 300113
Boot V 0101
Z point 300113
HCD900 SN 100042
Setting
>HOPP new SN Random3
display mode Button
Language ENG
Auto read Freq ON
Fig. 31

10
＊＊Remark＊＊
1. If the REMOCON remotes you prepare to copy the original remotes uses 3V
battery, please connect it to our HCD-900 by duplicating cable in advance before you
enter FixedCode Duplicate mode or HoppingCode Duplicate mode.
2. How to transmitting Seed Code from a REMOCON remote after duplication:
1) If there is only one Seed code for this remote: Press any 3 buttons at the same time.
2) If there are respective Seed codes for each button: Press the rest 3 buttons.
Example: If you would like to transmit the Seed code for button 1, press button 2, 3
and 4 at the same time; If you would like to transmit the Seed code for button 2, press
button 1, 3 and 4 at the same time.
3. Special rule for RMC-255CHM & RMC-255CHML: if you would like to copy both fixed
code remotes & rolling code remotes into RMC-255CHM or RMC-255CHML by
HCD-900, please ensure to copy fixed code remotes first(in FixedCode Duplicate mode)
and then copy rolling code remotes(in HoppingCode Duplicate mode). If you do it
reversely, the rolling code programmed will be covered by fixed code you copy later.
Updated at Apr. 18, 2017