Rensair Q01B User manual

INSTRUCTION MANUAL
MODEL: Q01B
Hospital-Grade Air Purifier
Rensair.com

MODEL: Q01B
Hospital-Grade Air Purifier
Air inlet perforaons
1
2
3
4
5
6
7
Air outlet perforaons
7.
50Hz

3
Press to switch on/off. When switched on, the unit will start in AUTO mode. As the
sensors determine the air quality, the fan speed will be set accordingly. NOTE: The
UV-C lamp will be turned on by default. Once the air quality is deemed
sasfactory, the unit will automacally switch to stand-by mode (under normal
condions, the unit will run for approx. 30 minutes prior to switching to stand-by).
For further air purificaon, operate the unit manually.
Lock the control sengs: In order to lock the keys of the panel, press the on/off
buon and hold it down for 5 seconds. To unlock: Repeat. Once locked, the unit
can be operated with the remote control.
Press to set the fan speed: from 1 (quiet = 300m³/h) to 3 (max. intensity = 560m³/h).
Press the buons to preset the operang me: + to increase, - to decrease (default
mer duraon is 8 hours). The mer can be in- or decreased by 30 minutes intervals
for up to 24 hours of operaon. The LCD screen displays the remaining me.
NOTE: Should only be used when the unit is serviced. Pressing the buon and holding it
down for 5 seconds to resets the memory of the filter life indicator.
MODEL: Q01B
Hospital-Grade Air Purifier

4
Insert two baeries. Make sure to insert the baeries according
to the polaries indicated on the remote control.
Choose the funcon buons corresponding to the buons on
the control panel on the Rensair air purifier.
Fan speed, 1(standard) to 3(highest capacity).
UV-C lamp on/off indicator. The UV-C lamp will be on by default. It is
recommended to keep the UV-C lamp turned on for highest air
purificaon effecveness.
Time le will only be indicated when mer funcon is turned on,
otherwise the unit will display the temperature in the room.
MODEL: Q01B
Hospital-Grade Air Purifier

5
Temp
The Service Indicator displays the remaining life of the filter. When bars light up all
the way to the illustraon on the right, it is me to service the unit. Please check the
status of the UV-C lamp and fliter when the service indicator is full. They must be
replaced when it lights on 4 mes.
MODEL: Q01B
Hospital-Grade Air Purifier
The Air Quality Indicator shows the quality of air based on number of parcles in the air
entering the unit: The fewer bars, the beer. The Rensair Air Purifier will operate
connuously when in AUTO mode if the air quality is not sasfactory.
Please make sure the power is cut off. Remove all four
filters by pressing the small clip buon and liing them
up. If possible shake dust off outdoors. Use a vacuum
cleaner to remove finer dust and use mild soap and
water to wash them. Make sure the filters are
completely dry before reinserng them.

6V1.0E
1
1
1
2
2
Turn the unit upside-down and place on a so surface,
e.g. a mat or a carpet to protect the display. Unscrew
the four bolts from the base and remove the filter by
liing it out, holding the rings at the base of the filter:
Once the holder ’clicks’ free, the lamp and the
holder can be carefully removed from its socket
by pulling upwards. Only use original Rensair parts to
avoid damaging the Rensair air purifier.
Re-assemble the unit in reverse order. Be careful not to damage the UV-C lamp
when pung the filter back in place.
Aer assembling, plug in the Rensair air purifier and press the RESET buon,
holding it down for 5 seconds. This will ensure that the Service Indicator is reset.
MODEL: Q01B
Hospital-Grade Air Purifier