Renu Electronics FP4101 Series User manual

Power (Base)
24VDC(+20%, -15%), 250mA, 6W (for T-E
module)
24VDC (+20%, - 15%), 270mA, 6.48W (for TN-E
module)
Power
(with 5 Expansions)
24VDC(+20%, -15%), 500mA, 12W (for T-E
module)
24VDC(+20%, -15%), 520mA, 12.48W (for TN-E
module)
Display
10.1”, 1024 x 600pixels, WVGA color TFT with
4-wire analog resistive touch screen
LEDs
1
RAM Memory
512MB
User Application
Up to 1GB that includes user application, data
log, alarms, retentive memory and logic
memory
eMMC
4GB
RTC
Built-in, date and time function
Expansion
It support 5 expansion slots*
Weight
Approx. 900gm
Product Dimensions
268.0(W) x 190.0(H) x 36.8(D)mm
Panel Cut-out
256.00(W) x 178.00(H)mm
Communication
COM1 and COM2
RS232/RS485
USB Ports
1 USB Type C Port and 1 USB Host Port
Ethernet
1 Ethernet Port
SD Card
Micro SD [High Capacity (4GB to 32GB)]
Speed Class:
[While inserting and removing SD card, please make
sure to TURNOFF the power to the unit.]
Environment & Approvals
Operating
Temperature
-10° to 60°C**
Storage Temperature
-20° to 85°C
Humidity
10 to 90% (Non-Condensing)
Shock
IEC 60068-2-27
25g, 11ms, 6 shocks per axis, total 18 shocks (X,
Y, Z)
Vibration
IEC 60068-2-6
5 to 150Hz, 3g peak (X, Y, Z)
EMC
EN 55011 : 2009/A1 : 2010
EN 61131-2 : 2007
EN 61000-6-2 : 2005/AC : 2005
EN 61000-6-4 : 2007/A1 : 2011
Protection
IP66 for front panel mounting
APPROVALS
CE, UL(Class1 Div2) & RoHS
[*Note: Applicable only for FP4101Tx-E models.]
[**Note: For UL, operating temperature range is 0° to 50°C.]
SPECIFICATIONS
PRODUCT DIMENSIONS
[Panel Cutout Dimensions: 256.00(W) x 178.00(H)mm,
Panel Thickness: Maximum 6mm and Mounting Clamps: 6]
Tighten the mounting screws evenly to a torque between 0.4N/m
to maintain water and dust resistance.
QUICK START GUIDE
FP4101 Series
Product Code:
FP4101T: 1024 x 600, WVGA, 10.1” color TFT with 4-wire
analog resistive touch screen with 2 comm port, one USB
Type C port & Host port.
FP4101TN: 1024 x 600, WVGA, 10.1” color TFT with 4-
wire analog resistive touch screen with 2 comm port, one
USB Type C port, one USB Host port & 1 Ethernet Port.
FP4101T-E: 1024 x 600, WVGA, 10.1” color TFT with 4-
wire analog resistive touch screen with 2 comm port, one
USB Type C port & Host port. It supports upto 5
expansions.
FP4101TN-E: 1024 x 600, WVGA, 10.1” color TFT with 4-
wire analog resistive touch screen with 2 comm port, one
USB Type C port, one USB Host port & 1 Ethernet Port. It
supports upto 5 expansions.
User should follow the given sequence to configure and
use any FlexiPanels series unit:
1. Install FlexiSoft Software.
2. Create a PZM application using FlexiSoft software.
3. Connect programming cable.
4. Download Firmware i.e. driver for the HMI.
5. Download application.
6. Now FP unit is ready to use in the system.
GETTING STARTED

This section provides information regarding communication interfaces
supported by this product.
COM1 & COM2: RS485/RS232
DB9 Female
Pin number
Signal
1
TX+(RS422/RS485)
2
TXD(RS232)
3
RXD(RS232)
4
RX+(RS422/RS485)
5
GN
6
NC
7
NC
8
TX-(RS422/RS485)
9
RX-(RS422/RS485)
Ethernet Port
1. Fully compliant with IEEE 802.3 / 802.3u standards.
2. 10/100 Mbps support.
3. Connector used: Standard shielded RJ-45 female jack with in-built speed
and link activity indication LEDs.
Pin number
Signal
1
TX+
2
TX-
3
RX+
4
NC
5
NC
6
RX-
7
NC
8
NC
USB Type C
1. USB Type C, compliant with USB 2.0 specification, self-powered device.
2. Connector used: Micro USB Type C Female connector.
Pin number
Signal
1
VCC
2
D-
3
D+
4
NC
5
GND
WARNING:
-> This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D
or non- hazardous locations only.
-> WARNING –EXPLOSION HAZARD –Do not disconnect equipment unless
power has been removed or the area is known to be non-hazardous.
-> WARNING –EXPLOSION HAZARD - Substitution of components may impair
suitability for Class I, Division 2.
-> WARNING - CAUTION, Battery May Explode If Mistreated. Do Not Recharge,
Disassemble or Dispose of in Fire.
-> The list of materials used in the construction of these devices with name of
sealed device - generic name of the material and the supplier's name and type
designation.
-> It is recommended that the user periodically inspect the sealed devices
used, for any degradation of properties and Replace the device if any
degradation is found.
Rev.
Description
Date
1.0
First Draft
23/03/2020
1. 1 .1
Replaced USB type from Micro to Type C
21/07/2021
RENU Electronics Pvt. Ltd® reserves the right to change or discontinue
specifications and features without prior notice.
To view the latest and updated datasheets/manuals please visit
www.renuelectronics.com.
REVISION HISTORY
CONTROL DRAWING NO# CNTL/DWG/FP4101/0218 VER.NO.:1.00
USB Host Port
1. USB Host, compliant with USB 2.0 specification
2. USB Host can be used to transfer logged data and historical alarm
to USB memory stick.
3. USB Host can handle only USB memory stick devices and can
source current up to 150mA only.
4. Connector used: Standard USB Type a Female connector.
Pin number
Signal
1
VCC
2
D-
3
D+
4
GND
Cable Diagrams
PC to unit programming cable (RS232):
2 Wire RS485 connections:
4 Wire RS485 connections:
Earthing
The optimum method for Earthing electronic equipment is to earth
it separately from other high-power systems, to earth more than one
unit of electronic equipment with a single-point earth. The Earthing
marked terminal (see below) is provided on the unit.
[Note: Do not use an earth that has an unstable impedance, such as painted
screws or earth subject to vibration.]
FP101Tx