Renu Electronics FP4043TN-E User manual

For More Information, visit
https://www.renuelectronics.com
Power
24VDC (+/- 20%, -15%), 140mA, 3.36W
(without Expansion)
250mA, 9.36W (with 1 Expansion)
Display
4.3” WQVGA color TFT with 4-wire
analog resistive touch screen
LEDs
1
RAM Memory
512MB
User Application
Up to 1GB that includes user application,
data log, alarms, retentive memory and
logic memory
eMMC
4GB
RTC
Built-in, date and time function
Expansion
It support 1 expansion slot
Weight
Approx. 400gm
Panel Cutout (mm)
111.00(W) x 80.00mm(H)
Product Dimensions
(mm)
120.00(W) x 89.0mm(H) x 31.5mm(D)
Communication
COM1/COM2*
RS232/RS485
USB Ports
1 USB Device and 1 USB Host
Ethernet
1 Ethernet Port
SD Card
Micro SD [High Capacity (4GB to 32GB)]
Speed Class:
[While inserting and removing SD card, please
make sure to TURNOFF the power to the unit.]
Environment & Approvals
Operating Temperature
-10° to 60°C*
Storage Temperature
-20° to 85°C
Humidity
10 to 90% (Non-Condensing)
Shock
IEC 60068-2-27
25g, 11ms, 6 shocks per axis, total 18
shocks (X, Y, Z)
Vibration
IEC 60068-2-6
5 to 150Hz, 3g peak (X, Y, Z)
EMC
EN 55011 : 2009/A1 : 2010
EN 61131-2 : 2007
EN 61000-6-2 : 2005/AC : 2005
EN 61000-6-4 : 2007/A1 : 2011
Protection
IP66 for front panel mounting
APPROVALS
CE, UL & RoHS
[*COM1 / COM2: This unit has one DB9 COM port that can be used as COM1 (RS232)
and / or COM2 (RS485/RS422). Special “Y” cable can be provided, if both the ports
are to be used simultaneously.]
(Part No.: REPL Part# EC-Y-FP)
[Note: *For UL, operating temperature range is 0°to 50°C.]
SPECIFICATIONS
PRODUCT DIMENSIONS
[Panel Cutout Dimensions: 111.00 x 80.00mm,
Panel Thickness: Maximum 6mm, Tolerance: +/-0.2mm]
QUICK START GUIDE
FP4043TN-E
Product Code:
FP4 043 TN- E
User should follow the given sequence to configure and use any
Flexi Panel series unit:
Install FlexiSoft Software.
Create a PZM application using FlexiSoft software.
Connect programming cable.
Download Firmware i.e. driver for the HMI.
Download application.
Now FP unit is ready to use in the system.
GETTING STARTED
Series
Display Size
Supports Ethernet
Supports Expansion

This section provides information regarding communication interfaces
supported by this product.
USB Slave Port:
1. USB Slave, compliant with USB 2.0 specification, self-powered device.
2. Connector used: Micro USB Type B Female connector.
USB Host Port:
1. USB Host, compliant with USB 2.0 specification
2. USB Host can be used to transfer logged data and historical alarm to
USB memory stick.
3. USB Host can handle only USB memory stick devices and can source
current up to 150mA only.
Connector used: Standard USB Type a Female connector.
COM1/COM2: RS232/ RS5485
DB9 Female (COM2)
Pin No.
Signal
1
TX+
2
TXD
3
RXD
4
RX+
5
SG
6
NC
7
NC
8
TX-
9
RX-
Ethernet Port
1. Fully compliant with IEEE 802.3 / 802.3u standards.
2. 10/100 Mbps support.
3. Connector used: Standard shielded RJ-45 female jack with in-built
speed and link activity indication LEDs.
Pin No.
Signal
1
TX+
2
TX-
3
RX+
4
NC
5
NC
6
RX-
7
NC
8
NC
Cable Diagrams:
PC to unit programming cable: RS232 Pinout
WARNING:
-> This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D
or non- hazardous locations only.
-> WARNING –EXPLOSION HAZARD –Do not disconnect equipment unless
power has been removed or the area is known to be non-hazardous.
-> WARNING –EXPLOSION HAZARD - Substitution of components may impair
suitability for Class I, Division 2.
-> WARNING - CAUTION, Battery May Explode If Mistreated. Do Not Recharge,
Disassemble or Dispose of in Fire.
-> The list of materials used in the construction of these devices with name of
sealed device - generic name of the material and the supplier's name and type
designation.
-> It is recommended that the user periodically inspect the sealed devices
used, for any degradation of properties and Replace the device if any
degradation is found.
Rev.
Description
Date
1.0
First Draft
24/03/2020
Renu Electronics Pvt. Ltd® reserves the right to change or discontinue
specifications and features without prior notice.
REVISION HISTORY
CONTROL DRAWING NO# CNTL/DWG/FP4043/0318 VER.NO.:1.00
2 Wire RS485 connections:
4 Wire RS485 connections:
Earthing
The optimum method for Earthing electronic equipment is to earth
it separately from other high-power systems, to earth more than one
unit of electronic equipment with a single-point earth. The Earthing
marked terminal (see below) is provided on the unit.
[Note: Do not use an earth that has an unstable impedance, such as
painted screws or earth subject to vibration.]
Models
Description
FPEM-1616P
16 Digital Inputs, 16 Digital Outputs (14
PNP, 2 outputs can be configured for PWM)
FPEM-1614RP
16 Digital Inputs, 14 Digital Outputs (12
Relay, 2 outputs can be configured for
PWM)
FPEM-1212P-A0200L
12 Digital Inputs, 12 Digital Outputs (10
PNP, 2 outputs can be configured for
PWM),
FPEM-1212RP-A0200L
12 Digital Inputs, 12 Digital Outputs (10
Relay, 2 outputs can be configured for
PWM), 2 Analog Inputs (Voltage / Current)
FPEM-1210P-A0201L
12 Digital Inputs, 10 Digital Outputs (8 PNP,
2 outputs can be configured for PWM),
2 Analog Inputs (Voltage / Current), 1
Analog Output (Voltage / Current)
FPEM-1210RP-A0201L
12 Digital Inputs, 10 Digital Outputs (8
Relay, 2 outputs can be configured for
PWM), 2 Analog Inputs (Voltage / Current),
1 Analog Output (Voltage / Current)
FPEM-0808P-A0401U
8 Digital Inputs, 8 Digital Outputs (6 PNP, 2
outputs can be configured for PWM),
4 Analog Inputs (Universal), 1 Analog
Output (Voltage / Current)
FPEM-0808RP-A0401U
8 Digital Inputs, 8 Digital Outputs (6 Relay,
2 outputs can be configured for PWM),
4 Analog Inputs (Universal), 1 Analog
Output (Voltage / Current)
FP4043Tx Series