Reolink Argus Eco User manual

Argus Eco
Argus Eco works cable-free with a rechargeable battery and reliable Wi-Fi
connection. Flexible and weatherproof – you can put it anywhere with 5-minute
installation!
1. Specs
1
Status LED
2
Built-in Mic
3
4 IR LEDs
4
Lens
5
Daylight Sensor
6
Built-in PIR Motion Sensor

Status Light
Status Light
Camera Status
Red light
Wi-Fi connection failed
Blue light
Wi-Fi connection succeeded
Blinking
Standby status
On
Working status
2. Setup and Install
Set up the Camera
What’s in the Box
Note: The package content may vary and update with different version and
1
On/Off Switch
2
Micro SD Card Slot
3
Speaker
4
Reset Hole
5
Antenna
6
Micro USB Port
7
Battery Status LED

platforms, please take the below information only for a reference. And the actual
package content are subject to the latest information on the product selling page.
Argus Eco
Set up the Camera on the App
Please follow the steps below to do initial setup for the battery-powered cameras
via Reolink App.
Step 1. Power on the camera. Remember to turn on the power switch on the
camera before initial setup except for Argus 2 and Argus Pro. After a startup sound,
you will hear a repeated Ding sound or a voice prompt.
Note: The voice prompt you will hear may be "Welcome to Reolink, please install
Reolink app and scan the QR code on the camera" in multilingual versions, or
"please run Reolink app, add the camera and set it up".
Step 2. Tap the icon in the top right corner to start the initial setup.
Surveillance Sticker*1
Pack of Screws*1
Reset Needle*1
Argus Eco*1
Mounting Template*1
Quick Start Guide*1
Outdoor Security
Mount*1
USB Cable*1

Step 3. Scan the QR code on the back of the camera. You may tap Light to enable
a flashlight when setting up the camera in a dark environment. If the phone
doesn't respond, please tap Input UID/IP and then manually type in the UID
(16-digit characters under the QR code of the camera). Then click Next.
Step 4. Select Wi-Fi Not Configured. If you hear a voice prompt played by the
camera, please tick correspondingly and then tap Next.

Step 5. Enter the WiFi password of the selected WiFi network (you may tap the
right eye icon to see and double-check the password) and tap Next.
Note: Argus Eco only supports the WiFi frequency of 2.4GHz.
Step 6. Tap Scan Now. Place the QR code on your phone in front of the camera’s
lens at a distance of about 30 cm (12 inches) and let the camera scan the QR code.
Tick correspondingly and tap Next.

Step 7. Wait around 60 seconds for the camera to connect to the router. After
hearing "connection to the router succeeded", tick correspondingly and tap Next.
Step 8. Create a login password and then name your camera.

Step 9. Read the note below and then tap Finish to complete the initialization of
your camera.
Once the initial setup is completed, you may choose a good position to mount your
camera.

Install the Camera
We offer you guides on different scenes in which the camera could be installed.
Check out them respectively.
Mount the Camera to the Wall
Step 1. Drill holes and screw the security mount into the wall.
Note: If you are mounting the camera on any hard surface, insert plastic anchors
into the holes first.
Step 2. Screw the antenna to the camera and install the camera to the mount.
Step 3. Loosen the adjusting knob and adjust the camera in the proper direction.
Step 4. Tighten the knob to fix the camera.

Attach the Camera to a Tree
Step 1. Thread the strap through the slots of the mounting plate.
Step 2. Fix the plate to the mount with screws.
Step 3. Fasten the strap onto the tree firmly.

Step 4. Attach the camera to the mount in the same way as in mounting it to the
wall.