ReSound Unite Phone Clip+ User manual

USER GUIDE
Phone Clip+
400227000-GB-12.08-Rev.A.indd 1
28-09-2012 11:48:57

2
Welcome
Congratulations on your purchase of a Phone Clip+.
Phone Clip+ will allow you to connect your wireless ReSound
hearing instruments to Bluetooth-enabled mobile phones. This
enables clear and hassle-free phone connectivity, whether you
are at home, in the office or on the move.
The Phone Clip+ also doubles as a basic remote control making
it possible for you to adjust to volume of your hearing instru-
ments and toggle through programs, when you are not talking
on the phone.
You can also chose to mute your hearing instrument microphone
to shut out environmental sound while you are talking on the
phone or when using the Phone Clip+ as a remote control (Verso
wireless family only).
Please read this manual carefully to fully benefit from the Phone
Clip+. Ask your hearing care professional if you have any ques-
tions.
For further information you can also check the http://www.
resound.com/products/accessories web site.
For your safety, carefully read the chapter Important Information,
on pages 25-31.
FCC ID: X26BTB-2
400227000-GB-12.08-Rev.A.indd 2
28-09-2012 11:48:58

3
Statement:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this de-
vice may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communi-
cations.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harm-
ful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for
help.
400227000-GB-12.08-Rev.A.indd 3
28-09-2012 11:48:58

4
Changes or modifications can void the user’s authority to oper-
ate the equipment.
Intended use
Phone Clip+ is intended to enable wireless ReSound hearing
instrument users to better follow phone conversations. The
essential performance of the Phone Clip+ is to transfer signals
between a phone with Bluetooth capabilities and wireless Re-
Sound hearing instrument.
When not used for phone conversations the Phone Clip+ can
also to be used as a basic remote control enabling volume ad-
justment, programs change and hearing instrument microphone
mute* functionality.
List of countries
Products are intended for use in countries within European
Economic Area as well as Switzerland.
*Verso wireless family only.
400227000-GB-12.08-Rev.A.indd 4
28-09-2012 11:48:58

5
National restrictions:
Norway: You are not allowed to operate the equipment within 20
km of the centre of Ny Ålesund.
This product is in compliance with the following regulatory
standards:
In EU: The device conforms to the Essential Requirements ac-
cording to - Annex I of Council Directive 93/42/EEC for medical
devices (MDD) and essential requirements and other relevant
provisions of Directive 1999/5/EC (R&TTE). The declaration of
conformity may be consulted at www.resound.com
In US: FCC CFR 47 Part 15, subpart C, section 15.247 and
15.249.
Other identified applicable international regulatory requirements
in countries outside EU and US. Please refer to local country
requirements for these areas.
The product is categorized as receiver category 2 according to
EN 300 440.
iC: 6941C-BTB2
This Class B digital apparatus complies with Canadian ICES-
003.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
400227000-GB-12.08-Rev.A.indd 5
28-09-2012 11:48:58

6
Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
In JP:
This device has been granted a designation number by Ministry
of Internal Affairs and Communications under „Ordinance con-
cerning Technical Regulations Conformity Certification etc. of
Specified Radio Equipment (特定無線設備の技術基準適合証明
等に関する規則)“ Article 2-1-xx “This device should not be modi-
fied (otherwise the granted designation number will be invalid)“
400227000-GB-12.08-Rev.A.indd 6
28-09-2012 11:48:58

7
Contents
Description ........................................8
Getting Started ....................................10
Turning your Phone Clip+ ON and OFF..................11
Bluetooth Pairing...................................13
Phone operation ...................................16
Volume Control ....................................20
Operating Time ....................................21
Wearing Your Phone Clip+ ...........................21
Light indicators ....................................22
Introduction to Bluetooth ............................23
Important Information ...............................25
Technical specifications .............................32
Warranty .........................................33
Troubleshooting guide ..............................36
400227000-GB-12.08-Rev.A.indd 7
28-09-2012 11:48:58

4
5
2
13
8
Description
1. ON/OFF switch
2. Call pick-up/hang-up button
3. Hearing instrument program toggle
4. Hearing instrument microphone mute button
5. Micro-USB for charging
400227000-GB-12.08-Rev.A.indd 8
28-09-2012 11:48:59

910
7
8
6
9
6. Volume control
7. Microphone inlet
8. Mounting clip
9. Hearing instrument pairing button
10.Bluetooth pairing button
400227000-GB-12.08-Rev.A.indd 9
28-09-2012 11:48:59

10
Getting Started
Charging the Battery
Before using your Phone Clip+, you
need to fully charge the rechargeable
battery.
To charge it, plug the charging cable
into the Phone Clip+ as shown in the
picture to the right.
Then plug the other end of the charg-
ing cable into a power outlet.
During the charging process, the light
indicator (LED) at the top of the Phone
Clip+ will show a solid red light.
When fully charged and still connected to the charger, the LED
will turn solid green interrupted by a red blink every 2 seconds.
Charging an empty battery typically takes around 3 hours. It is
safe to leave the charger connected overnight – the battery can-
not be overcharged.
• When charging your Phone Clip+ for the first time, leave it
to charge for at least 3 hours, even if the battery indicator
shows that the unit is fully charged (see section about “Light
indicators”).
• For safety reasons, recharge the battery only with chargers
supplied by ReSound.
400227000-GB-12.08-Rev.A.indd 10
28-09-2012 11:49:00