Resource Decor DUKE UK KING BED User manual

DUKE UK KING BED
Thank you for choosing this quality product. Be sure to check all packaging materials carefully for small parts that may have
become loose during shipment and place all parts on a non-abrasive surface.
IMPORTANT :These parts can be cumbersome and heavy to some people, therefore the assistance of two or more people is
recommended in order to prevent personal injury and ensure the furniture is not damaged during the assembly Process.
PART LIST
A [1] HEADBOARD
B [2] SIDE RAILS
C [1] FOOTBOARD
D [1] SUPPORT SLAT
E [2] WOODEN PANEL
F [2] CANOPY RAILS
HARDWARE LIST
NO.
1
2
3
4HEXAGONAL NUT
THREADED ROD
CURVED WASHER
LOCK WASHER
DESCRIPTION QTY
8 PCS
5WRENCH
1 PC
PAGE 1 OF 2
8 PCS
12 PCS
8 PCS
6
7
8
9
MINI FIX BOLT
MINI FIX LOCK WITH LOCK
ALLEN WRENCH
SCREW
1 PC
4 PCS
4 PCS
18 PCS
CARE INSTRUCTIONS
1. Dust often using a clean, soft, dry and lint-free cloth.
2. Blot spills immediately and wipe with a clean, damp, cloth.
3. We do not recommend the use of chemical cleansers, abrasives or furniture polish on our lacquered finish.
IMPORTANT SAFETY INSTRUCTIONS
1. Please read all instructions carefully before assembling.
2. Keep instructions for future use.
3. Use only vendor supplied hardware to assemble. Using unauthorized hardware could jeopardize the structural integrity
of the item.

ASSEMBLY INSTRUCTION
The bed is composed of several
components: The headboard, foot board,
side rails, support slats, wooden panel ,
canopy rail. Determine the intended
location and ensure there is enough space
to work with and fully read these
instructions before physically doing the
entire assembly.
STEP #1:
Remove the mini fix lock from the mini fix
nut (7), as per illustrated in FIGURE 1.
STEP #2:
Place the headboard (A) upright in the
position you wish the bed to be in when
fully assembled. The headboard bed fast
hardware should be facing inside, toward
the mattress. Secure the threaded rod (1)
and mini fix bolt (6) to the fixed nut in the
headboard (A) by simply turning it
manually. Raise the side rail (B), canopy rail
(F) and place the rod (1) to align with the
bore holes on the end of the side rails (B),
place mini fix bolt (6) to align with the bore
holes on the end of the canopy rails (F) but
before that insert the mini fix nut (7) into
each hole on top surface of the canopy rails
(F). Use a screwdriver to adjust this nut to
make sure the hole on it is inline with the
bore hole on the end of the canopy rail. Put
the side rails (B) and canopy rails (F) up
against the headboard (A) so the threaded
rods (1) and mini fix bolt (6) go through the
bore holes. Insert curved washer (2), lock
washer (3) and place hex nuts (4) on
threaded rod (1) then tighten the hex nuts
(4) with wrench (5) provided, see FIGURE
03. Tighten mini fix lock connect the canopy
rails (F) to the HB & FB, see FIGURE 02
STEP #3:
Repeat the above procedure with the other
side rail (B) and canopy rail (F) to attach it
to the headboard (A), and then repeat to
connect to the footboard (C).
STEP #4:
On inside face of both headboard (A) and
footboard (C) are pre-installed wooden
brackets for the support slat (D). Set the
support slat (D) on the wooden brackets, as
illustrated in FIGURE 04.
STEP #5:
Lay the two wooden panels (E) on top of
assembled bed and secure these with
screws (9) provided as in FIGURE 05.
Thank you for your purchase
PAGE 2 OF 2
FIGURE 04
FIGURE 05
2
1
4
B
A/C
3
5
E
9
FIGURE 03
FIGURE 01 FIGURE 02
6
A/C
8
F
A/C
D
Mini fix nut (7)
Mini fix lock
Allen
wrench (8)