Resource Decor EMERSON DISPLAY CABINET User manual

EMERSON DISPLAY CABINET
Thank you for choosing this quality product. Be sure to check all packaging materials carefully for small parts that may have loosened
inside the carton during shipment and place on a non-abrasive surface.
IMPORTANT
These parts can be cumbersome and heavy to some people, therefore, the assistance of two or more people are recommended in
order to prevent personal injury and ensure the furniture is not damaged during the assembly Process.
NO D ESC RI PT I O N QTY
1
2
3
4
HARDWARELIST
PHILLIPSHEAD BOLT 4
HANDLE 2
PART LIST
A. [ 1] CABINET
B. [ 3] REMOVABLESHELFFRAME
C. [ 5] SHELFGLASS
SHELFHOLDER
SCREW
12
12
5
BUMPON PLASTIC 50
6
KEEPER 2
INSTRUCTIONS
1. For packing purpose, the door handles with keepers were
removed and put in hardware bag. Open all doors, attach
the handles (1) with keepers (2) to the door by using the
Phillips head bolts (3) provided. Repeat this steps to
attach handle for other doors. Refer to FIGURE01.
1
2
3
Page 1 of 3

2. Install the shelf holders (4) and place the shelf panels (B)
on the shelf holders. Fix the shelf panels to the shelf
holders by using screws (5) provided. See FIGURE 02.
3. S
ecure place the Bumpon plastic (6) on the top of the
shelf frame and then place the Shelf glass (C) on it. See
FIGURE 03.
4. Check the table leveling, and adjust the levelers at the
bottom of the base if necessary. See FIGURE 04.
B
4
5
FIGURE 02
c
6
FIGURE 03
Fig.03
Fig.04
Fig.02
FIGURE 04
Leveler
Page 2 of 3

CAREINSTRUCTIONS
1. Dust often using a clean, soft, dry and lint-free cloth.
2. Blot spills immediately and wipe with a clean, damp, cloth.
3. We do not recommend the use of chemical cleansers,
abrasives or furniture polish on our lacquered finish.
IMPORTANT SAFETY INSTRUCTIONS
1. Please read all instructions carefully before assembling.
2. For your safety, assembly by two or more adults is strongly
recommended.
3. Keep instructions for future use.
4. Use only vendor supplied hardware to assemble. Using
unauthorized hardware could jeopardize the structural
integrity of the item.
INSTALLATION INSTRUCTION
1. Attach two of the Plastic Brackets near the top back edge of the
furniture piece by inserting the shorter screws .
2. Determine the final position of the furniture piece. Mark
locations on the wall approximately 2" below the brackets
mounted to the back of the furniture.
3. Drill a shorter hole into the wall stud. If wall stud is not available,
drill a hole into the wall and insert Plastic Anchor. Gently tap the
Anchor until the flange is flush with the wall.
4. Attach the second set of brackets by inserting the longer screw
through the bracket and into the wall.
5. Carefully move the chest backward within 1.5" to 2" from the
wall.
6. Place the furniture so that the brackets on the back edge are in
line with the brackets in the wall.
7. Lace one end of the nylon restraint strap down through each
bracket. Bring both ends together and slide the beaded end until
it snap locks into the keyhole slot.
8. To double lock; return the beaded end back through the keyholes
as shown.
9. Check to make sure the straps are securely laced and locked to
the brackets.
FURNITURETIPPING RESTRAINT INSTRUCTIONS
Young children may be injured by tipping furniture and
the use of a tipping restraint is highly recommended.
When properly installed, this restraint could provide
protection against the unexpected tipping of furniture
due to small tremors, bumps or climbing. We
recommend mounting this restraint to a wall stud.
WARNING: This product is only a deterrent. It is not a
substitute for proper adult supervision.
8
9
7
10
11
Wall
NO D ESC RI PT I O N QTY
7
8
9
10
PLASTIC BRACKET 4
RESTRAINT STRAP 2
PHILLIPSSCREWS(M4 x 30) 4
4
PLASTIC ANCHOR 4
PHILLIPSSCREWS(M4 x 20)
11
Page 3 of 3