Restoration Hardware 1930S Lab Double Vanity Sink User manual

page 1
1930S LAB DOUBLE VANITY SINK ASSEMBLY INSTRUCTIONS
2. Opening crate
1. Before unpacking make sure you have installation requirements present:
1.A professional two man crew
2. Sink base installed according to instructions with plumb wall and floor.
3. Ensure the marble top is the correct one for the base.
4.Tools and materials required:
1. Flat, non-abrasive work surface, such as a blanket or smooth cardboard
2. Carpenter’s level
3. Phillips head screwdriver
4. Sealant
2. Carefully, without allowing any free fall,
rotate the crate from vertical to flat.
This is the only time the crate should be horizontal.
1. Storage
1. Keep marble top in it’s crate until installation.
2. Store crate vertically in a place safe from being hit or knocked over
3. Do not stack anything on top of the crate.

page 2
1930S LAB DOUBLE VANITY SINK ASSEMBLY INSTRUCTIONS
3. Remove metal bands
4. Unscrew the slats or lid and remove.
3. Examination of marble top
1. Examine the marble top for cracks or defects.
2. If defects are detected, please call 877-777-7059, do not install.
3.To clean the marble top, wipe with a soft cloth.
4. Installation of marble top
1.Always use a two man crew, a single person crew is much more likley to break or chip the marble top.
Double tops might require a 3 man crew.

page 3
1930S LAB DOUBLE VANITY SINK ASSEMBLY INSTRUCTIONS
2. Specific Instructions for installation between two walls
1. Set top on it’s edge at back of counter.
2. Lower the front of the marble top to the sink base, making sure both ends come down at the same rate.
3. Do not shimmie, twist or turn the top as you lower it. - risk of breakage!
If defects are detected please call 877-777-7059 - do not install.
Caution! Installation between two walls requires special care.

page 4
1930S LAB DOUBLE VANITY SINK ASSEMBLY INSTRUCTIONS
Before You Begin:
Professional installation by two-person crew is required for this fixture. Install water supply and drain piping according to local
plumbing and building codes. Insure that wall and floor are square and plumb at site of installation.
Tools and Materials Required:
1. Flat, nonabrasive work surface such as a blanket or smooth cardboard
2. Carpenter’s level
3. Sealant
4. Phillips head screwdriver
ASSEMBLED SINK

page 5
1930S LAB DOUBLE VANITY SINK ASSEMBLY INSTRUCTIONS
Parts List
Stone top (sold separately)
Backsplash (sold separately)
Lavatory basin (x2)
Vanity base
A.
B.
C.
D.
Parts List
Calk in anchor (x8)
Calk in anchor sleeve (x8)
“L” Bracket (x8)
Washer (x8)
Screw (x8)
Setting Tool
E.
F.
G.
H.
I.
J.

page 6
1930S LAB DOUBLE VANITY SINK ASSEMBLY INSTRUCTIONS
1.
2.
Assembly Instructions:
Using two people, carefully place stone top upside down on a flat, non-abrasive surface.
Using setting tool (J), hammer calk-in anchors (E) straight into pre-drilled holes on underside of stone top. (see illustration)

page 7
1930S LAB DOUBLE VANITY SINK ASSEMBLY INSTRUCTIONS
Cleaning and Maintenance Instructions:
Avoid abrasive and harsh chemical cleaners.
To maintain and protect luster of vanity sink components, Restoration Hardware Bathroom Cleaning Products are
recommended.
Restoration Hardware natural stone tops have a honed finish and hand-polished edges. They are sealed twice before shipment with
inert silicone sealant. For cleaning and maintenance, Restoration Hardware Stone Care Products are recommended. To maintain
your natural stone top, reseal it once a year.
Apply a continuous bead of sealant to the top surface of rim of lavatory basin (C) where it will contact underside of stone top.
Position lavatory basin in its final location, upside down on underside of stone top. Overflow of lavatory basin should be on
same side as pre-drilled faucet holes on stone top.
Place four “L” brackets (G) with long sides over the lavatory basin rim.
Insert screws (I) through washers (H) and “L” brackets. Screw into calk-in anchors with screwdriver. (See Illustration.)
(Do not over-tighten.) Insure that lavatory basin is securely attached to stone top.
Using two people, turn stone top with attached basin over and position carefully on top of vanity base.
3.
4.
5.
6.

23
SIDE VIEW
66
FRONT VIEW
66
TOP VIEW
34
4
23
1358
Ø 114
8
34
1358
8
Ø 114
2234
66
34
2478
BACK VIEW
12 2234

Ø 1.25
31.75
4.06
103.13
13.61
345.72
3.51
89.04
4.25
107.95
11.81
300.00
23.00
584.20
10.15
257.84
66.00
1676.40
20.21
513.36
4.00
101.60
13.61
345.72
NOTE: ALL STONE IS 30 MM THICK
3.00
76.20
65.50
1663.70
FRONT ELEVATION OF BACKSPLASH
SCALE: 1 : 5
LABORATORY & PHARMACY 66 DOUBLESTONETOP
COPYRIGHT © 2012RESTORATIONHARDWARE,INC.
DWG #: 1 of 1
CONFIDENTIAL. OWNED BY RESTORATIONHARDWARE,INC. NOT TO BE USED OR
COPIEDWITHOUTEXPRESSWRITTENPERMISSION OF RESTORATIONHARWARE,INC.
DATE:03/02/12
R .25
6.35

RECTANGULAR BASIN
DRAWINGS REPRESENT ORIGINAL DESIGN SPECIFICATIONS. ACTUAL PRODUCT DIMENSIONS MY VARY SLIGHTLY.
ALL DIMENSIONS ARE REPRESENTED IN INCHES.
PROFESSIONAL INSTALLATION REQUIRED
Unless otherwise noted, all design and content, images, artwork, graphics, photography, text, and the like are copyrights, trademarks, trade dress, and/or intellectual property that are owned, controlled, or licensed by Restoration Hardware.