Retekess PR16R User manual

Amplifier Opereation Manual
PR16R
Henan Eshow Electronic Commerce Co., Ltd
Add: 7/F, Sanjiang Building, No.170 Nanyang Road, Huiji District,
Zhengzhou, Henan, China
Facebook：facebook.com/RetekessRadio
E-mail: [email protected]
Web: www.retekess.com MADE IN CHINA

1
2345
678 9
11
10
Product control diagram
1
2
3
4
5
6
7
8
9
11
10
Antenna
Recording key
Next song
Pause/play
Last song
Mode
Turn on / increase in volume
Turn off / turn off the volume
TF card jack
U disk socket
Charging port
1

suitable position between the waist.
2. Put the head on the head, adjust the microphone position, it is best to leave the mouth
in front of the 1-2CM, the other end of the head microphone 3.5 plug into the mainframe
microphone Jack;
Method of use
1. Take out the main machine in the package, fasten the round hole on both sides of the
back of the main machine with belt buckle, tie the main machine on the waist or hang
on the shoulder through the belt, can adjust the belt to let the main machine be in the
Operation mode
1. Sound Amplification
Turn the power on key to the "on" state. When you hear the sound of "ka", it means
that the power supply has been turned on. At this time, it means that the machine can
be used normally and inserted into the "microphone" socket caused by the standard
microphone of the local machine. The system automatically, by default, is in the state
of amplifying. Note: Under any function, press the "pause" button, and other functions
will stop, and the amplifying effect will be even better. If you turn it to the maximum
sound, the distance from the machine will be pulled away. It is recommended that the
distance between head and mouth is about 1 cm.
2. Mode key (M)
This key has the function of mode switching. When there is a U disk or TF card, you
can switch between the U disk / TF / FM / by pressing the long and short press mode
key. When there is no U disk or TF card, the mode key can be received by pressing
Description of FM Wireless microphone
1. First turn on the FM wireless microphone and set a frequency. The general recomme-
ndations are for frequencies such as 101.0, 108.0 and 87.5, and cannot overlap with
the frequency of local stations.
2. Then turn on the megaphone host and press M to switch to radio mode.
3. Long press the play / pause button to allow the host to search the station automatically.
4. When the host is finished, press one or the next key and switch to the same frequency
as the FM wireless microphone to begin amplifying.
5. Next time you turn on the microphone directly and turn on the loudspeaker host switch
to radio mode. If you cannot connect it, you can repeat the 3.4 Steps. If the noise inte-
rference is serious, a transmission frequency can be reset on the wireless microphone,
starting from step 1.
* This page only applies to FM wireless machines, and does not mean that all machines
have this feature.
2 3

the computer or USB port of the USB charger. The USB charge head is required to be
5V / L 500mA, and the recommended time for single charge is 4 to 6 hours.
Note: For the first time, the battery has a small amount of power, but in order to
achieve the best results, it is recommended that the battery be fully charged
before it can be used.
6. Last song (long click on the key when playing music to achieve fast retreat)
For last song, in U disk ATF card / FM status, short press this button to adjust the
program you want, in FM state short press for the previous channel, external audio
source key mode short press invalid.
7. The next song (the music can be played long by pressing the key to a quick
retreat)
For next song, in U disk / TF / FM mode, short press this button to adjust the program
you want. In FM state, short press to reach the next channel. In external source key
mode, the short press is invalid.
8. One-key recording
Insert the wired microphone and insert the USB / TF card, and short press recording
key to make record. After the recording is completed, short press the "recording"
button, and the file will automatically be saved to the U disk / TF card, which is
convenient and easy to operate.
the mode key. When playing music, long press the mode key about 2 seconds to
realize the single loop and the whole cycle switch. When ONE appears on the screen,
it is a single loop. When the screen appears ALL, it refers to all songs loop.
3. TF/ U disk playback
After correctly inserting TF card / U disk into TF card / U disk in accordance with the
direction of fuselage identification, press M key to integrate into audio mode and play
audio files in TF card / U disk normally.
4. FM radio
1) Slowly pull out the antenna.
2) Press M to switch to FM mode.
3) Long press the play button for more than 2 seconds, after watching the number on
the screen changes, release hands, waiting for automatic platform search and save.
When the number on the screen stops changing and starts playing FM, it means
that the station is searched and saved.
4) Change the channel by pressing the last song or the next song. Note: The radio
effect is directly related to the signal, if not ideal, please take it outdoor or besides
window to test.
5. Charge
When the machine needs to charge, plug the smaller end of the standard USB chargi-
ng line into the mirco USB charging port of the fuselage, and plug the larger end into
4 5

Product selling point
Data parameter
1. Digital display screen, easy to understand
2. One key recording function, easy to operate and fast
3. This product is a multifunctional portable loudspeaker with sound amplifying, digital
music playing and radio function.
4. Imported high-power amplifier chip and advanced off-fidelity amplifier master control
5.Using high-power speakers, the sound effect is clear and loud, covering a wide
range of transmission.
6.High capacity, high safety, environmental protection class A 18650 lithium battery.
Matters needing attention
1. In order to achieve the best effect of microphone amplification, please place the head
in front of the mouth at the front of the 1CM at the head of the pronunciation. If there is
a howl, you can turn down the volume properly or the distance quotient between the
machine and the head of the microphone is slightly removed to prevent interference.
2. Avoid frequent plugging of microphone socket so as to avoid loosening the socket and
causing poor contact. You should not insert the words simply or incorrectly into the
sound source.
3. In order to ensure the service life of lithium battery, it is suggested that recharging is
Output power
Output impedance
Charging voltage
Use music time
Frequency response
Working temperature
Use of amplification time
Charging time
12W
2 Ω
DC 5V 1A
6-10 Hours
50HZ-15000Hz
-10℃-45℃
12-18 Hours
4-6 Hours
Standard product distribution
Loudspeaker
Belt
USB power cord
Copy of manual / warranty card
Microphone
Name Quantity
1 pcs
1 pcs
1 pcs
1 pcs
1 pcs
Remarks: TF card, U disk, USB charging head are optional accessories, can be purchased as
needed.
6 7

Self-solving of frequently asked questions
1.Switch on, amplifiers have no sound
A.The screen lights are not on, the power supply is out of power, charge to solve it
B.Screen lights on, whether the microphone is plugged in the wrong position.
Guarantee
Remarks:
1. This guarantee card should be kept by the user, no replacement if lost.
2. Most new products carry a two-year manufacturer’s warranty from the date of purchase.
Further details, pls read http://www.retevis.com/after-sale/
3. The user can get warranty and after-sales service as below:
• Contact the seller where you buy.
• Products Repaired by Our Local Repair Center.
4. For warranty service, you will need to provide a receipt proof of purchase from the
actual seller for verification.
Exclusions from Warranty Coverage:
1. To any product damaged by accident.
2. In the event of misuse or abuse of the product or as a result of unauthorized alterations
or repairs.
3. If the serial number has been altered, defaced, or removed.
conducted after using up, because frequent charging will accelerate the aging of the
battery chip, and the battery should be recharged every two months when it is not
used for a long time.
4. Because the horn magnetic effect is strong, do not put the machine and the bank card
and other magnetic things together, lest cause the loss of magnetism and cause unne-
cessary trouble.
5. All the accessories of this product are designed according to the requirements of the
machine. If we need to replace the accessories, we can use the original parts to
achieve the best working condition.
• There is a risk of explosion if the battery is not replaced properly, and only the same
type or equivalent type of battery can be used to replace the battery.
• The operating environment of the machine is -10 ℃-45 ℃, and the battery (battery
pack or combination battery) shall not be exposed to such conditions as sunlight, fire
or similar overheating.
• Batteries are polluting, please dispose of end-of-life batteries and machines properly
2. The loudspeaker has a distinct howl
A.Make sure you wear a microphone and point the mark at the corner of your mouth.
B.When the space becomes small, you should lower the voice appropriately in order
to reduce the howling in reverberation.
8 9

Guarantee Warnings
Local Government Regulations
When the radios are used as a consequence of employment, the Local Government
Regulations requires users to be fully aware of and able to control their exposure to meet
occupational requirements. Exposure awareness can be facilitated by the use of a product
label directing users to specific user awareness information. Your Retekess radio has a
RF Exposure Product Label. Also, your user manual, or separate safety booklet includes
information and operating instructions required to control your RF exposure and to satisfy
compliance requirements.
Compliance with RF Exposure Standards (If appropriate, Reference to the
actual product’s Safety Marking)
Your Retekess radio is designed and tested to comply with a number of national and
International standards and guidelines (listed below) for human exposure to radio
frequency electro-magnetic energy.
Before using this radio, read this guide which contains
important operating instructions for safe usage and RF
energy awareness and control for compliance with
applicable standards and regulations.
Model Number:
Serial Number:
Purchasing Date:
Dealer:
Telephone:
User’s Name:
Telephone:
Country:
Post Code:
Email:
Address:
10 11

FCC ID
The FCC ID means: This radio complies with the IEEE (FCC) and ICNIRP exposure limits
for occupational/controlled RF exposure environments at operating duty factors of up to
50% talk-50% listen and is approved for occupational use only.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reas-
onable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The CE marking means: Hereby, Henan Eshow Electronic Commerce Co.,Ltd.
declares that the radio equipment type is in compliance with the RED Directive
2014/53/EU and the ROHS Directive 2011/65/EU and the WEEE Directive
2012/19/EU. The full text of the EU declaration of conformity is available at the
following internet address: www.tivdio.com
IC ID
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
• This device may not cause interference, and
• This device must accept any interference, including interference that may cause
undesired operation of the device.
In terms of measuring RF energy for compliance with these exposure guidelines, your
radio generates measurable RF energy only while it is transmitting (during talking), not
when it is receiving (listening) or in standby mode.
12 13

Avoid Choking Hazard
Small Parts. Not for children under 3 years.
Protect your hearing
• Use the lowest volume necessary to do your job.
• Turn up the volume only if you are in noisy surroundings.
• Turn down the volume before adding headset or earpiece.
Turn off your radio power in the following conditions:
• Turn off your radio before removing (installing) a battery or accessory
or when charging obattery.
• Turn off your radio when you are in a potentially hazardous environ-
ments: Near electrical blasting caps, in a blasting area, in explosive
atmospheres (inflammable gas, dust particles, metallic powders,
grain powders, etc.).
• Turn off your radio while taking on fuel or while parked at gasoline
service stations.
To avoid electromagnetic interference and/or compatibility conflicts
• Turn off your radio in any facility where posted notices instruct you to do so,
hospitals or health care facilities (Pacemakers, Hearing Aids and Other
Medical Devices) may be using that is sensitive to external RF energy.
• Turn off your radio when on board an aircraft. Any use of a radio must be in
accordance with applicable regulations per airline crew instructions.
Avoid Burns
Antennas
• Do not use any portable radio that has a damaged antenna. If a damaged
antenna comes into contact with the skin when the radio is in use, a minor
burn can result.
Batteries (If appropriate)
• When the conductive material such as jewelry, keys or chains touch exposed
terminals of the batteries, may complete an electrical circuit (short circuit the
battery) and become hot to cause bodily injury such as burns. Exercise care
in handling any battery, particularly when placing it inside a pocket, purse or
other container with metal objects.
WARNING
WARNING
WARNING
14 15

EU Importer：
Name：Germany Retevis Technology GmbH
Address：Uetzenacker 29,38176 wendeburg
WARNING
Long transmission (If appropriate)
• When the transceiver is used for long transmissions, the radiator and chassis
will become hot.
Safety Operation
Forbid
• Do not use charger outdoors or in moist environments, use only in dry
locations/conditions.
• Do not disassemble the charger, that may result in risk of electrical shock
or fire.
• Do not operate the charger if it has been broken or damaged in any way.
• Do not place a portable radio in the area over an air bag or in the air bag
deployment area. The radio may be propelled with great force and cause
serious injury to occupants of the vehicle when the air bag inflates.
To reduce risk
• Pull by the plug rather than the cord when disconnecting the charger.
• Unplug the charger from the AC outlet before attempting any maintenance
or cleaning.
• Contact Retekess for assistance regarding repairs and service.
16