RetroSound TWO Installation instructions

Model Two Radio
Installation and Owner's Manual
Made
for
~
iPod
CiPhone
AM/FM
Radio
with
iPod®/iPhone®,
USB
MP3/WMA
Playback
and lnfiniMountShaft/Bracket System
r
~
The information enclosed in this installation manual
is
to
be used
as
a guide
to
assist you during
the
process
of
installation. This guide does
not
cover
every installation possibility, vehicle,
or
every aspect
of
the
installation
process.
Retro Manufacturing,
LLC,
RetroSound®,
or
its subsidiaries, assume no
responsibility
for
any installation. This manual may be updated
from
time
to
time.
Please check
our
website
for
the
latest updates: www.retrosoundusa.com.

Model Two Owner's Manual
NOTES:
Copyright
2014
©
Retro Manufacturing,
LLC
No text, illustrations,
or
format
of
this manual in printed
or
electronic
form
may be copied
without
written
permission from Retro Manufacturing,
LLC
or
any
of
its subsidiaries. All Rights Reserved.
I
Copyright 2014
©
Retro Manufacturing,
LLC

Model
Two Owner's Manual
Table
of
Contents
Licensing......................................................................................... 2
Welcome! ....................................................................................... 3
What's in
the
Box
...........................................................................4
Warnings and Precautions.............................................................. 5
Installation Warnings...............
~
...................................................... 8
Installation Instructions
.................................................................. 9
Wiring Instructions....................................................................... 13
Using Your Radio (Basic Operation).............................................. 15
Adjusting Sound Properties.......................................................... 20
Sub-Menu System ........................................................................ 24
USB
Device Instructions
................................................................ 30
Bluetooth Instructions
..................................................................
32
Troubleshooting ............................................
·
............................... 34
Frequently Asked Questions.........................................................
35
Specifications................................................................................
37
Limited Warranty.......................................................................... 38
Copyright 2014 © Retro Manufacturing,
LLC

Model Two Owner's Manual
Licensing
"Made
for
iPod®" and
"Made
for
iPhone®" mean
that
an
electronics accessory
has
been designed
to
connect specifically
to
iPod®
or
iPhone® respectively, and
has
been certified by
the
developer
to
meet
Apple performance standards.
Apple
is
not
responsible
the
operation
of
this device
or
its compliance
with
safety and regulatory standards. Please note
that
the
use
of
this accessory
with
iPod
or
iPhone may affect wireless performance. Apple
is
not
responsible
for
the
operation
of
the
device
or
its compliance
with
safety and regulatory stan-
dards.
iPod and iPhone are trademarks
of
Apple Inc., registered in
the
U.S.
and
other
countries.
Windows Media® and
the
windows logo are trademarks,
or
registered trade-
marks
of
Microsoft
Corporation in
the
United States
and/or
other
countries.
The Bluetooth®
word
mark and logos are owned by
the
Bluetooth
SIG,
Inc.,
and any use
of
such marks by Retro Manufacturing,
LLC
is
under license.
Other
trademarks and trade names are those
of
their
respective owners.
Made
for iPod
(Correct
function
of
earlier versions cannot be guaranteed.)
• iPod touch (4th generation):
Ver.
5.1.1
• iPod touch (2nd generation):
Ver.
4.2.1
• iPod touch (3rd generation):
Ver.
5.1
• iPod nano (6th generation):
Ver.
1.1
• iPod nano (5th generation):
Ver.
1.0.2
• iPod nano (4th generation):
Ver.
1.0.4
• iPod nano (3rd generation):
Ver.
1.1.3
• iPod classic (160GB) (Late 2009):
Ver.
2.0.4
• iPod classic (120GB):
Ver.
2.0.1
• iPod classic (80GB, 160GB):
Ver.
1.1.2
Made
for iPhone
{Correct
function
of
earlier versions cannot be guaranteed.)
• iPhone 4s:
Ver.
5.1.1
• iPhone 4:
Ver.
5.1.1
• iPhone
3GS:
Ver.
5.1.1
• iPhone
3G:
Ver.
4.2.1
For clarity in identifying
your
model
of
iPod, please
see
Apple's
document
"Identifying iPod models" at
http:/
/support.apple.com/kb/HT1353.
Copyright 2014 © Retro Manufacturin

Model Two Owner's Manual
Welcome!
The Model Two combines classic styling
with
the advanced features you expect
from a modern car stereo.
General Features
• The only classic car radio compatible
with
iPod and iPhone
• Built-in Bluetooth
for
hands-free calling and audio streaming
•
Plays
MP3 and
WMA
files via
USB
input
• Selectable 32,000 color
LCD
illumination
with
user presets
•
AM/FM
tuner
with
30 presets and
RDS
• Selectable USA/EU/Japan/AUS/RUS
tuner
frequencies
• Built-in amplifier (25 watts RMS/45 watts peak x 4 channels)
• 3
EQ
presets plus user-controlled
bass,
treble, fader, mid-range and balance
adjustment
• Authentic push-button styling
•
lnfiniMount
shaft/bracket system
for
maximum installation flexibility
• Compatible
with
all RetroSound® vehicle specific bezel, plate and knob kits
• Inputs: 2 rear-mounted standard
USB
ports and 2 rear auxiliary inputs
• Outputs: 6-ch pre-amp outputs (front, rear, subwoofer)
• Separate
power
antenna and amp turn-on lead(s)
• 2 year parts and labor warranty
• Includes vintage-look radio screen protectors
Copyright 2014 © Retro Manufacturing,
LLC

Model Two Owner's Manual
What's
in
the
Box
The accessory items and hardware shown below are packaged
with
your
Model Two radio.
Main Wire Harness
(Plug
into
back
of
radio)
Power/Speaker
Wire
Harnesses
(Plug both into Main Wire Harness)
000000
Plastic Washer Kit
Shaft/Bracket
Mounting
Hardware
Bluetooth
Microphone
Shaft Covers (2)
Removable
lnfiniMount
Shafts (2)
8
0
Mounting
Backstrap
and Hardware
Copyright 2014
©
Retro Manufacturing,
LLC

Model
Two Owner's
Manual
Warnings and Precautions
This equipment
has
been tested and found
to
comply
with
the
limits
for
a
Class
Bdevice, pursuant
to
Part 15
of
the
FCC
Rules.
These limits are designed
to
pro-
vide reasonable protection against harmful interference in a residential instal-
lation. This equipment generates, uses and
can
radiate radio frequency energy,
and,
if
not
installed and used in accordance
with
instructions, may cause harm-
ful interference
with
radio communications. However, there
is
no guarantee
that
radio interference will
not
occur in a particular installation.
If
this equip-
ment
does cause harmful interference
to
radio
or
television reception, which
can
be
determined by
turning
the equipment
off
and on, the user
is
encouraged
to
consult
the
dealer
or
an
experienced radio/TV technician
for
help.
You
are
cautioned
that
any changes
or
modifications
not
expressly approved in this
manual could void your
authority
to
operate this equipment.
Observe these warnings and precautions
when
using this
unit:
• Carefully read
this
manual before using
the
unit.
If
you encounter any
problems
that
are
not
covered in this manual, please consult
the
dealer
from
which you purchased the
unit
or
the dealer nearest you.
You
may also
email
us
at [email protected].
• Do
not
turn
the
unit
on
if
the
temperature
inside
the
car
is
very
high.
Always allow
the
unit
to
cool
down
before usage.
• The
driver
should
neither
watch
the
display
nor
operate
the
system
while
driving. Watching
the
display
or
operating
the
system will distract the
driver
from
driving safely and
can
cause accidents. Always stop the vehicle
in a safe location and
use
the
parking brake before watching the display
or
operating
the
system.
• Use
the
proper
power
supply. This product
is
designed
for
operation
with
a negative ground 12V
DC
battery system. Never operate this product
with
other
battery systems, especially a 18/24V
DC
battery
or
positive ground
system.
• Do
not
disassemble
or
modify
the
unit.
Do
not
disassemble, modify
the
unit
or
attempt
to
repair
the
product yourself.
If
the product needs
to
be
repaired, consult your dealer
or
Retro Manufacturing directly.
• Do
not
use
the
unit
when
it
is
out
of
order.
If
the
unit
is
out
of
order (no
power, no sound)
or
in
an
abnormal state (has foreign objects in it,
is
ex-
posed
to
water,
is
smoking,
or
smells),
turn
it
off
immediately and consult
your dealer.
Copyright 2014
©
Retro Manufacturing,
LLC

Model Two Owner's Manual
• Refer fuse replacement to qualified service personnel. When the fuse
blows out, eliminate
the cause and have it replaced with the fuse pre-
scribed
for this unit by a qualified service technician. Incorrect replacement
of the fuse may lead to smoke, fire, and damage to the product.
• If the unit does not turn on, check the connections first. Then check
whether the fuse in your vehicle's fuse box is blown and check the fuse at
the unit's wiring harness.
Observe these warnings and precautions during installation:
• Do not expose the unit to direct sunlight or excessive heat. Excessive heat
will raise
the interior temperature of the unit, which may damage the unit.
• Do not use the product where it is exposed to water, moisture, or dust.
Exposure of the unit to water, moisture, or dust may lead to smoke, fire, or
other damage to the unit and void your warranty. Make sure that the unit
does not get wet in car washes or on rainy days.
• Refer wiring and installation to qualified service personnel. Installation of
this unit requires special skills and experience. For maximum safety, have it
installed by your dealer. Retro Manufacturing is not liable for any problems
resulting
from your installation of the unit. Please be sure to follow our
instructions carefully before attempting installation.
• Follow the instructions to install and wire the product. Not following the
instructions to properly install and wire the product could damage the unit
or cause an accident or fire.
• Disconnect the lead from the negative (-) battery terminal before installa-
tion. Wiring and installation with the negative(-) battery terminal con-
nected may cause electrical shock and
injury due to a short circuit. Some
cars equipped
with an electrical safety system have specific procedures
for battery terminal disconnection. FAILURE TO FOLLOW THIS PROCEDURE
MAY LEAD TO THE UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY
SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL INJURY
OR DEATH.
• Take care not to damage the leads. When wiring, take care not to damage
the leads. Prevent them from getting caught in the vehicle chassis, or
from being damaged by screws or moving parts, such as seat rails. Do not
scratch, pull, bend or twist the leads. Do not run them near heat sources or
place heavy objects on them. If leads must be routed around sharp metal
edges,
protect the leads by winding them with vinyl tape or similar protec-
tion.
Copyright 2014 © Retro Manufactu ·

Model
Two Owner's
Manual
• Use
the
designated parts and
tools
for
installation.
Use
the supplied
or
designated parts and appropriate tools
to
install the product. The
use
of
parts
other
than those supplied
or
designated may result in internal
damage
to
the
unit. Faulty installation may lead
to
an
accident, malfunction
or
fire.
• Do
not
use safety-related vehicle components
Be
careful
not
to
wire or
affix this product
to
the following parts
of
the
vehicle: fuel tank, brake,
suspension, steering wheel, pedals, airbag, etc.
• In
the
case
of
installation
to
an airbag-equipped car, confirm warnings
and cautions
of
the
vehicle
manufacturer
before installation.
• Check
for
piping, gasoline tank, electric
wiring,
and
other
items before
installing
the
product.
If
you need
to
open a hole in the vehicle chassis
to
attach
or
wire
the
product, first check where
the
wire harness, gasoline
tank, and electric wiring are located. Then open the hole from outside
if
possible.
• Never install
the
product
in a location
where
it
interferes
with
your
field
of
vision.
• Never splice
into
the
power
cord
to
supply
other
equipment
with
power.
•
After
installation and
wiring,
you should check
the
normal
operation
of
other
electrical
equipment.
The continuation
of
their
use
in abnormal
conditions may
cause
fire, electrical shock
or
a traffic accident.
•
Make
sure
the
leads
do
not
interfere
with
driving
or
getting
in
and
out
of
the
vehicle.
• Insulate all exposed wires
to
prevent
short
circuiting.
• Do
not
operate
the
unit
for
a prolonged period
with
the
engine
turned
off. Operating the audio system
for
a long period
of
time
with
the
engine
turned
off
will drain the battery.
Copyright 2014
©
Retro Manufacturing,
LLC

Model
Two Owner's
Manual
Installation Warnings
I
•
To
ensure
proper
operation
of
this
RetroSound product, please
read these instructions carefully before installing and using
this
equipment.
This owner's manual does
not
cover all possible installation scenarios.
If
you
feel you can't install this product yourself, please take
it
to
a local car audio
professional,
or
contact
us
at [email protected]
or
call
702-483-2222
1
888-325-1555.
I
•
I
•
I
•
IMPORTANT!
PLEASE
NOTE
THAT
THIS
UNIT
REQUIRES
+12V
TO
BOTH
THE
RED
&
YELLOW
WIRES,
OTHERWISE
THE
UNIT WILL
NOT
OPERATE.
CONTACT
US
IF
YOU
HAVE
QUESTIONS.
Disconnect
the
negative (-)
battery
cable before beginning installa-
tion.
Verify
the
battery ground by checking
that
one wire
is
connect-
ed
to
the starter mounting
bolt
or
engine block and
another
to
the
vehicle chassis using at least #8 gauge wire. Make sure
the
alterna-
tor
connections are secure and free from corrosion, rust
or
dirt.
WARNING!
To
prevent
damage
to
the
unit,
do
not
connect
the
power
connector
until
you have completed
the
wiring
process.
This
is
a 12
volt
negative-ground
ONLY
radio.
If
you have a positive
ground system,
or
a
6-volt
system, you need
to
either
convert
to
12
volts
or
purchase a separate
inverter
that
would
step
up
the
volt-
age
to
12 volts. Please
note
that
the
inverter
needs
to
be rated
at
8
amps
or
higher in
order
for
the
Model
Two
to
operate properly.
Copyright 2014
©
Retro Manufacturing,
LLC

Model Two Owner's Manual
Installation Instructions
NOTE: Getting the unit tofit perfectlyinto your dash is probably the most
difficult portion of the install. Patience and persistence is the key. Ifyou still
have problems, please contactus at [email protected] or
702-483-2222
The
lnfiniMount system offers nearly unlimited installation options to accom-
modate your
fit needs.
To begin, locate the removable lnfiniMount shaft system and the lnfiniMount
"L" brackets, as well as two each large and small washers (see "What's in the
Box" on page 4). For more advanced installations, please visit our website:
retrosoundusa.com
or email [email protected].
STEP 1: lnstalllnfiniMount Brackets
Attach each lnfiniMount bracket using the supplied screws. Before tightening,
adjust the brackets forward or backward, or rotate to achieve the perfect fit.
Complete
the assembly with 2 or 4 screws tightened on either side.
Figure 1 -Attach InfiniMount Brackets
NOTE: You can move ourbracketsforward orbackward and move them in
any direction. You can even cut, trim or bend the bracket orcreate your own
bracketfor a more challenging installation. For more advancedinstallations,
please visit
our website: www.retrosoundusa.com oremailsupport@
retrosoundusa.com.
Copyright 2014 © Retro Manufacturing, LLC

Model Two Owner's Manual
STEP 2: Mount Shafts to Brackets
1. To match the lnfiniMount shaft and bracket system to the proper shaft
width of your vehicle, first measure the distance between your existing
shaft holes from center
to center.
2. Mount a shaft system to each bracket using the supplied shaft nuts, metal
and plastic washers.
3. Finger tighten to prepare for the final installation (see Figure 2).
Use supplied
washers and nuts
to place shafts
onto brackets.
Important: DO NOT
overtighten.
Figure 2 - Mount Shaft to Bracket
4. Once sure of the proper width, tighten prior to final installation. Be sure to
plug the shafts into each side of the main unit to activate the shaft-control
functions (see Figure 3).
NOTE: Each of the shafts can operate on either
side of the radio and are not left/right dependant.
Figure 3- Insert Shaft Plugs
NOTE: Modifying orcutting the radio's brackets will not voidyour warranty.
The system is designed to accommodate any installation scenario.
STEP 3: Complete Wiring Connections
See "Wiring Instructions" on page 13.
l¢iJj!.l Copyright 2014 © Retro Manufacturing,
LLC I

Model Two Owner's Manual
STEP
4: Adjust
to
Fit Your Vehicle Specific Kit
One
of
the
most frequent questions we get
is
"How
can
your radio
fit
my car?".
The Model Two radio
is
a universal solution (one chassis
for
most vehicles) and
its control face
is
a fixed
size
(3.5" W x 1.5"
H).
Most
American cars
fit
the
radio
and
the
bezel
from
behind
the
dash. The bezel fits around
the
Model Two con-
trol
face
to
fill
the
original factory opening.
The Model Two control face
is
NOT
referred
to
as
a faceplate. A faceplate
is
a
piece
that
overlays
or
covers
the
top
or
front
of
the
dash. A faceplate
is
used in
most European
or
Japanese cars, and
can
also be used on a modified dash
to
disguise any blemishes
or
poorly made modifications.
Locate
the
appropriate bezel
or
faceplate and perform the following steps
to-
mount
the
radio behind
the
dash opening:
FACEPLATE:
Use
the
supplied nuts and washers
to
align
the
faceplate
onto
the
shaft.
DO
NOT
overtighten. Once
the
shafts are lined up
to
the
shaft openings
on
your
vehicle-specific faceplate,
use
a
nut
and washer
to
hold
the
faceplate in
place on
the
shafts. Adjust
the
nut
height
so
that
the
faceplate aligns flush
with
your dash and
the
radio's control face.
See
"Figure
4-
Install Vehicle Specific
Faceplate".
BEZEL:
Place
the
bezel on
the
face
of
the
radio and install through
the
back
opening
of
your
dash.
NOTE:
With
the
faceplate picturedbelow, the area around
the
radio face
(chrome
or
black) mountson
top
of
the dash.
Pia
Metal
Shaft-
Nuts/washers installed between
Lbracket and faceplate
Figure
4-
Install
Vehicle
Specific
Faceplate
DO
NOT
OVERTIGHTEN SHAFT NUTS!!
ICopyright 2014 © Retro Manufacturing,
LLC
l§ij!i

Model Two Owner's Manual
STEP 5: Install Knobs
Once your radio is installed, follow the steps below to ensure a proper knob fit.
1. The included shaft covers may be used to cover up excess shaft metal
during
your installation. They can be cut to any length to conceal the shaft
and make
the install look more professional. See Figure 5 for an example.
2. Slide the rear knob over the shaft, rotating it into the correct position, and
push
it into place. See Figure 6.
3. Mount the front knob. See figure 7 and 8.
Figure 5 - Shaft
Cover Installed (Note:
this is an optional
item to install)
l@tgjfl
Figure 6 - Install
Rear Knob
Figure 7 - Install
Front Knob
Optional1967 -68 Camara faceplate
Figure 8 - Final Result
Copyright 2014 © Retro Manufacturing, LLC I

Model Two Owner's Manual
Wiring
Instructions
PLEASE
NOTE THAT THIS
UNIT
REQUIRES
+12V
TO BOTH THE
RED
AND
YELLOW WIRES, OTHERWISE THE
UNIT
WILL
NOT
OPERATE.
CONTACT
US
IF
YOU HAVE QUESTIONS.
[email protected]
or
702-483-2222
Wiring
Diagram {Figure
9)
Locate
the
three wire harnesses: Main Wire Harness, Power Wire Harness and
Speaker Wire Harness (see
~~what's
in
the
Box" on page 4). First connect
the
Main Wire Harness
to
the
back
of
the
radio. Then connect both
the
Power
and Speaker Wire harnesses
to
the black female plug
of
the Main Wire Harness.
After doing this, connect the bare wire ends
of
your power and speaker wires
to
the
appropriate power and speaker locations in your vehicle.
(see
Figure
9,
11
Wiring Diagram" on page 14)
Please
contact
us
if
you have questions
or
have
your radio installed by a professional
if
this part
of
the install
is
too
difficult.
Installation Notes
•
To
prevent damage
to
the unit, do
not
connect the power connector until
you have completed
the
wiring process.
• This
is
a 12
volt
negative-ground
ONLY
radio.
If
you have a positive ground,
or
a 6-volt system, you need
to
either
convert
to
12 volts
or
purchase a
separate inverter
that
would step up
the
voltage
to
12 volts.
• Please note
that
the inverter must be rated at 8 amps
or
higher in order
for
the radio
to
operate properly.
Rear AUX Inputs
Two rear auxiliary inputs all
low
you
to
listen
to
any portable device
with
stan-
dard headphone outputs.
An
example
of
an
external source would
be
a por-
table
CD
player, mini disc player, portable cassette recorder, iPod
or
MP3 player.
Select
an
auxiliary
input
mode by turning
the
left rear knob clockwise until you
see
RU><
IN
I
or
RUX
IN
2 on the Model Two's screen.
USB
Extension Cable
Two
USB
connector cables are located at the rear
of
the
Model Two radio.
During installation, you must route
the
cable(s)
to
a convenient and acces-
sible location
for
plugging in
USB
devices.
If
the
cable(s) provided are
not
long
enough {40 inches), you may plug in optional
USB
extensions during installation.
Copyright 2014
©
Retro Manufacturing,
LLC

Model
Two Owner's Manual
~~ottnL
Model
Two
AMJFM
RADio
w1
use
INPUT
Frequency
Range:
FM
87.5-107.9
MHZ
AM
530-171
0
KHz
AUX INPUT 1
AUX INPUT 2
NOTE:
You
can
plug
yourflash drive
or
iPod/
iPhone
into
either
USB
input.
SUBWOOFER LINE OUT
(Blue Wire)
Connect Power Wire Harness
..
and Speaker Wire Harness
CONSTANT +12V
IGNITION/ACC (connect to +12V)
(Red Wire)
GROUND
(Black Wire)
POWER ANTENNA
(Blue Wire)
REMOTE/AMP TURN-ON LEAD
White/Black
Stripe
(-)
(+)
0
Left Speaker
(Front)
(Blue/White Wire)
(-)
(+)
~
Right Speaker
(Front)
40HM
NOTE: Yellow
and
Red wires
must
be
connected to
+12V
for
radio
to operate.
NOTE: This radio
is designed
for
use in vehicles
with a
12
volt
negative
ground
system.
(-)
(+)
0
Left Speaker
(Rear)
ANTENNA
BLUETOOTH
MICROPHONE INPUT
REAR RCA LINE OUT
(Grey Wire)
FRONT RCA LINE OUT
(Black Wire)
Purple/Black
Stripe
(-)
(+)
0
Right Speaker
(Rear)
NOTE:
Maximum
operational
distance
of
a
USB
cable
is
16
feet. For
optimum
data
transfer,
we
recommend
no
more
than
12
feet
of
total
cable length.
Figure
9 -
Wiring
Diagram
Copyright 2014
©
Retro Manufacturing,
LLC
l

Model Two Owner's Manual
Using Your Radio (Basic Operation)
Front Panel Controls
Figure 10 - Front Panel Controls
Both shafts are designed for a front
and rear knob, which have push func-
tionality. The photo on
the left shows
the left shaft (1 and 2 in Figure 10) with
knobs installed. Use the "Operation
Table" on page 16
to determine how to
use the knobs to achieve the desired
response
from your Model Two radio.
Figure 11 - Shaft with Knobs
ICopyright 2014 © Retro Manufacturing, LLC

~s=>owzct:
Model Two Owner's Manual
Operation Table
Function # Radio
Mode
USB
Mode
Power
On/Off
Volume
Audio
Adjust
Mode
Clock
On
View
Song
Info/
Clock
Preset 1
Recall/
Store
Play/
Pause
1
Press
the
left
front
knob
to
turn
the
unit
on. Look
for
RETROSOUNO
on power up.
Press
and hold
the
left
front
knob
for
3 seconds
to
turn
the
unit
off. The
LCD
display will show
GOOOB':IE
for
your confir-
mation.
1 Turn
the
left
front
knob
to
adjust
the
volume attenuation
between
0-46
(Min/Max). 17
is
the default turn-on volume
level.
1
Press
the
left
front
knob
to
activate the
SEL
(Select) func-
tion.
Press
repeatedly
to
cycle through
the
DSP
(Digital Signal
Processing)
EQ,
Bass,
Mid, Treble, Balance,
Fader,
XBAS,
Subwoofer and Subwoofer specific adjustments (when
SUB
ON
is
selected). Turn
the
left
front
knob
to
select a value.
See
"Adjusting Sound Properties" on page 20
for
detailed
instructions.
2 Turn
the
left rear knob clockwise
to
select
from
an
avail-
able listening source:
RADIO,
USB-1, USB-2,
AUX-1, AUX-2,
BT
AUDIO. Two sets
of
AUX
inputs are located at
the
rear
of
the
radio.
To
utilize these inputs,
AUX
cables must
be
routed
to
an
accessible area during installation.
See
"Wiring
Instructions" on page 13.
NOTE: The
USB
option
will
not
appear
unless
media
is
pluggedinto
the
USB
connector.
2 Turn
the
left rear knob Turn
the
left rear knob
counter-clockwise
to
activate counter-clockwise
to
toggle
the clock on-screen feature. and view artist, album,
title
information, clock.
3
Press
to
select
the
#1
radio
Press
to
play/pause file play-
preset. back.
Press
and hold
to
store
preset 1
into
memory.
Copyright
2014
©
Retro Manufacturing
JLCJ