REVELL NANO Hexagon User manual

2
AA
AA
AA
AA
CHARGING
INSTALL THE BATTERIES INTO THE CONTROLLER
1. Plug charger into computer or USB charge adapter. The LED on the
charger will turn on.
2. Make sure that the On/Off switch on the Nano Hexagon is off and
connect charger. The LED on the charger will turn off while the
battery is charging.
3. Typical charge time is 40 minutes. LED will turn on when the battery
is charged.
• NEVER leave the battery unattended while charging.
• DO NOT allow the USB port to power down while the
charger is connected to the battery.
• ALWAYS unplug the charger from the USB port and
the Nano Hexagon when charging is complete.
Remove the battery cover screw and the battery cover.
Install 2 AA batteries and replace the cover.

3
MOTOR ARMING
1. Turn on . Make sure the left
stick is at its lowest position.
The motors are now armed and your Nano Hexagon is ready to fly.
2. Place the Nano Hexagon on a level surface.
3. Turn on the Nano Hexagon and wait for the controller to beep twice.
4. Advance the left stick to its highest position and wait for the controller to beep once.
5. Return the left stick to its lowest position and wait for the controller to beep one more time.

4
BASIC FLYING
2. Moving the right stick in any
direction will make the Nano
Hexagon fly in the same direction.
3. The Nano Hexagon will rotate its
nose left or right when the left
stick is moved to the left or right.
1. To take off, SLOWLY advance the left stick until
your Nano Hexagon lifts off.
Please keep in mind that when the front of the model is pointed toward you, moving the sticks on the
controller will appear to move the Nano Hexagon in the opposite direction. To avoid confusion, try to
imagine that you are in the middle of your Nano Hexagon when flying.

5
FLIGHT MODES
TRIMMING
When your Nano Hexagon is hovering, a little drifting is normal. If it is always drifting in the same
direction, pressing the button that will provide the opposite trim should correct the problem.
For example, you would push the right trim to button stop the Nano Hexagon from drifting to the left. Each time a trim
button is pressed, the controller will make a short beep. A long beep is made when the trim adjustment is at its center
position. If the Nano Hexagon requires more than 20 clicks of trim, a Sensor Calibration may be needed.
The sensitivity of the controls can be changed by pressing down on the left stick.
1 Beep: Beginner Mode - least sensitive setting (default setting)
2 Beeps: Normal Mode – moderate sensitivity
3 Beeps: Expert Mode – highest sensitivity

6
FLIP MODE
LOW BATTERY INDICATOR
SENSOR CALIBRATION
After the Nano Hexagon has been flying for about 6 minutes, the LEDs on the arms will flash. This is a warning to land and charge the battery as
soon as possible. Always charge the battery when the flight is completed. When the LEDs are flashing, the Nano Hexagon will not have enough
power to perform a flip. Remember to ALWAYS turn off the Nano Hexagon after flight!
If your Nano Hexagon will not hover in the same spot when the right stick is
centered, the sensors may need calibration.
1. Place the Nano Hexagon on a level surface.
2. Center the trim adjustments. The controller will make a long beep when the
trim is at the center position.
3. Change the control sensitivity to the Expert Setting (page 5). Move both
sticks to their lowest position and to right as far as possible. The LEDs on the
hex will flash for a few seconds while the sensors are being calibrated.
ON OFF
The Nano Hexagon has a built in flip function. When the right stick is
pressed down, the TX will make a short beep to indicate it is in the flip
mode. When the right stick is moved, the Nano Hexagon will flip in the same
direction.

7
BLADE REPLACEMENT
BATTERY REPLACEMENT
Your Nano Hexagon has 3 “A” rotor blades which spin clockwise and 3 “B” rotor blades
which spin counterclockwise (when viewed from above). The arms have a letter to
identify proper rotor blade. The letter is also on the bottom of each rotor blade. If the rotor
blade and arm letters do not match, the Nano Hexagon will not be able to fly.
When the props are installed correctly, the blades on the “A” arms should have a
clockwise pitch. The “B” arms will have counterclockwise pitch.
IMPORTANT! If the props are installed
incorrectly, the Nano Hexagon will not fly.
B
B
B
A
A
A
If the battery will not hold a charge or the flight time is much less than normal, a replacement
battery may be needed. A soldering iron will be needed to remove and install the battery.
1. Remove the 6 screws on
the bottom of the Nano
Hexagon
.
2. Carefully separate two halves of the
body and remove the lower half.
3. Carefully solder in the new battery.
Note: The red wire is soldered next to
the B+ marking on the frame.
WARNING: Cover any bare
battery wires with tape when they
are loose to prevent arcing and
possible damage to the battery.

8
MOTOR REPLACEMENT
TROUBLESHOOTING
A damaged motor is not hard to replace, but a soldering iron will be needed
to remove and replace the motor wires from the frame.
1. Remove the screws and remove the lower half of the body as described in
the previous section.
2. Remove the prop from the damaged motor.
Select a replacement motor with the same color wires and note where they
are soldered to the frame before removing the damaged motor.
PROBLEM: Nano Hexagon will not respond to signals from the controller.
SOLUTION: (1) Recharge the flight battery. (2) Turn off the Nano Hexagon
and the controller. Wait 15 seconds and re-link them.
PROBLEM:
LED on the controller is flashing and the controller is working
correctly.
SOLUTION: Replace the AA batteries in the controller.
PROBLEM: The Nano Hexagon will not flip.
SOLUTION: Recharge the flight battery.
PROBLEM: The Nano Hexagon shakes while flying.
SOLUTION: Check for damaged motors or rotor blades.
PROBLEM: The rotor blades are spinning, but the Nano Hexagon will not
take off.
SOLUTION: (1) If any of the rotor blades were just replaced, verify that
they were correctly installed. (2) Recharge the flight battery.
PROBLEM: The Nano Hexagon is drifting or will not remain in a stable
hover.
SOLUTION: (
1) Check for damaged rotor blades. (2) Check the motors
for hair or lint below the rotor blades. (3) Make sure that
the Nano Hexagon is level when linked to the controller. (4)
Use the trim buttons to correct the drift (see the Trimming
section). (5) Calibrate the sensors on the Nano Hexagon (see
the Sensor Calibration section).

9
BATTERY PRECAUTIONS
SAFETY PRECAUTIONS
•ALWAYS disconnect the battery from the hexacopter when not in use.
•Only use the included charger with the flight battery.
•Do not attempt to use this charger with NiCd or NiMH battery packs.
•Do not attempt to use a damaged battery.
•This product contains a LiPo battery. Must be recycled or disposed of
properly.
•Do not leave the charger unattended while charging. Disconnect the
battery and unplug the charger immediately if either becomes hot!
However, it is normal for the charger to get warm.
•Disconnect the battery from the charger and carefully move the battery
to a fireproof location if the battery begins to swell or smoke!
•Never allow the battery temperature to exceed 140° F [60° C].
•Do not attempt to charge a battery if it is swollen or hot.
•Do not place the charger or any battery on a flammable surface or near
combustible materials while in use.
•Never disassemble or modify pack wiring in any way or puncture cells.
•Never charge inside a vehicle.
•Always disconnect the battery and remove the charger from the USB
port when not in use.
•Land your model immediately when the LEDs flash to indicate that the
battery power is low. Recharge the battery before attempting another
flight. A dangerous situation can occur when attempting to recharge an
over-discharged battery!
•ALWAYS keep a supply of sand accessible when charging. Dumping sand
on the battery will extinguish a LiPo chemical fire.
•ALWAYS KEEP OUT OF REACH OF CHILDREN
•Adult supervision required.
•Before flying, go to www.knowbeforeyoufly.org.
•Do not touch the spinning blades or fly over another person’s head.
•Keep your face and body as well as all spectators away from the rotors
whenever the battery is connected.
•Stay clear of buildings, trees and power lines. AVOID flying in or near
crowded areas. DO NOT fly close to people, children or pets.
•Maintain a safe pilot-to-hexacopter distance while flying.
•Your Nano Hexagon should not be considered a toy, but rather a small,
working model. If not operated correctly, the model could possibly cause
injury to you or spectators and damage to property.
•You must check the operation of the model before every flight to insure
that the model has remained structurally sound.
•Do not alter or modify the model, as doing so may result in an unsafe or
unflyable model.
The Nano Hexagon uses a lithium polymer (LiPo) battery. Follow these precautions to insure safe and trouble-free operation.
Follow these safety precautions when operating this or any model hexacopter.

10
REPLACEMENT PARTS
1
2
4
5
3
3
3
1RVLE1620 Motor Set (6)
2RVLE1621 Rotor Blade Set (6)
3RVLE1622 Body Set w/screws BLACK
3RVLE1623 Body Set w/screws ORANGE
4RVLE1626 LiPo Battery 1S 3.7V 150mA
5RVLE1627 USB Charge Cord

11
90-DAY LIMITED WARRANTY
FCC STATEMENT AND INDUSTRY CANADA NOTICE
PLEASE DO NOT RETURN YOUR PRODUCT TO THE STORE. Revell will repair or replace factory defects for 90 days from the date of
purchase. This warranty specifically does not cover crash damage, misuse or abuse.To make a warranty claim, please contact our product
support team at 1-217-398-8970 option 6 or e-mail us at [email protected].
If requested by Product Support, please send defective product to: Hobby Services, 3002 N Apollo Dr., Suite #1, Champaign, IL 61822
Please include a note about the problem, your contact information, and a copy of the receipt.
This warranty applies only if the product is operated in compliance with the instructions and warnings provided with each model. Revell
assumes no liability except for the exclusive remedy or repair of parts as specified above. Revell shall not be liable for consequential or
incidental damages. Some states do not allow the exclusion of consequential or incidental damages so the above exclusion may not apply
to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
1. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Remark: This device is in accordance with the digital device grade B limitation and the 15th regulation of FCC. This limitation requires reasonable anti-
interference protection around the residence. The device can transmit radio wave during use and can interrupt the mobile communication without proper
installment. Interruption will occur for special device. If the device do interrupt the radio or television, please turn the device off then turn it on to adjust.
Below are some resolution for your reference:
•Move the receiving antenna •Enlarge the distance between the device and receiver
•Try to not connect the device and the receiver on the same circuit •Ask for professional help from experts
3. This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference
Regulations of Industry Canada.

CE COMPLIANCE INFORMATION FOR THE EUROPEAN UNION
INSTRUCTIONS FOR DISPOSAL OF WASTE EQUIPMENT BY PRIVATE USERS IN THE EUROPEAN UNION:
This symbol on the product or its packaging indicates this product must not be disposed of with other household waste. Instead, it is the user’s
responsibility to dispose of their waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that
it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for
recycling, please contact your local city office, your household waste disposal service or location where you purchased the product.
DECLARATION OF CONFORMITY:
Product: Revell Control 2.4GHz 4-Channel Tx Rx
Item number: 23947/8
Equipment class: 1
23947/8 transmitter: The objects of the declaration described here are in conformity with the requirements of the specifications listed below,
following the provisions of the European 2006/95/EC Low Voltage Directive:
EN 60950-1:2006 Safety
The objects of the declaration described here are in conformity with the requirements of the specifications listed below, following the
provisions of the European R&TTE directive 1995/5/EC:
EN300 328 V1.8.1.
Technical requirements for radio equipment
ETSI EN 301 489-1 V1.8.1, 301 489-17 V1.3.2 General EMC requirements for radio equipment
Hobbico, Inc.
2904 Research Road
Champaign, IL USA 61826
Distributed in Europe by Revell GmbH
D-32257 Bünde Germany
The associated regulatory agencies of the following countries recognize
the noted certifications to this product as authorized for sale and use.
UK DE DK BG SE FI GR
EE LV LT PL CZ SK HU
RO SI AT IT ES PT IE
NL LU MT CY
RVLE09**
© 2015 Revell Inc. A subsidiary of Hobbico, Inc.