REVENTON VELO Silver Series User manual

Domestic axial fan with throttle
VELO and VELO Silver series
User Manual
Introduction
Thank you for choosing our product. Reading of this manual
is required for proper use of the device and absolute
observance to its guidelines is fundamental condition
of security.
All users of the device should have free access
to the manual and in case of resale, the instruction must
be attached to the product.
Package contents
- domestic axial fan VELO
- user manual
Transport and storage
The fan should be transported and stored in the original
packaging in a dry place protected from contamination,
until it is installed. Moreover, the fan should be protected
from the shocks.
Application
Axial fans from the VELO series are designed for wall
mounting. They are used for ventilation of small spaces
such as a bathroom or kitchen.
The device comes in two colors - white or silver (VELO Silver
version).
Construction of the device
1 –Panel 2 –Sensor 3 –Casing
4 –Motor 5 –Rotor ,w 6 –Throttle frame
7 –Throttle 8 –Fastening ring 9 - Frame
Dimensions (in mm)
MODEL
ØA
B
C
D
VELO 100 & VELO SILVER 100
100
150
90
35
VELO 150 & VELO SILVER 150
150
193
100
35
Technical data
MODEL
VELO 100 &
VELO Silver 100
VELO 150 &
VELO Silver 150
Maximum aiflow [m3/h]
95
240
Maximum compression [Pa]
36
60
Voltage [V] / Frequency [Hz]
230 / 50 - 60
230 / 50 - 60
Rated current [A]
0.072
0.138
Engine speed [rpm]
2400
2000
Engine power [W]
12
18
IP protection degree [-]
X4
X4
Noise [dB(A)]
34
35
Installation instructions
In order to accomplish the installation of the device
successfully and enable the safe usage of the fan
in the future, it is essential to follow the instructions in this
manual.
Before installing and connecting the fan, check that it has
not been damaged during transport or storage (breakage,
distortion).
Check whether the technical data on the nameplate
corresponds to the electrical installation parameters.
The device should be mounted on a flat surface.
If irregularities are not found, you can proceed
with the installation as follows:
- prepare appropriate electrical wires
- mark the location of mounting holes
- drill the holes and put expansion bolts in them
- place the fan in the right place and tighten screw it
- connect the device to electrical grid
The electrical connection must be in accordance
with the wiring diagram in the terminal box.
Warnings and precautions
During the operation of the device, the following
precautions must be observed:
- before performing any work, the device must
be disconnected from the power supply
- the fan is intended only for ventilation of rooms with small
and medium cubature
- if you do not use it for a long time, it is recommended
to disconnect the device from the power supply

- a constant supply of fresh air to the room must be ensured
- do not use the fan in a hazardous environment (i.e. near
flammable materials, in a heavily polluted one) or in a place
where it could be exposed to direct contact with water
- fan working temperature range is from -15oC to 40oC
- some elements of the fan can become hot and touching
them may cause burns
- unusual sounds during fan operation may indicate
a malfunction
- failure to comply with the guidelines contained in this
manual may result in damage to health or pose a threat
to the life of the user
Maintenance
Maintenance of the device should be carried out
depending on the working conditions, but not less than
once a year.
Before starting any maintenance operations, disconnect
the fan from the power supply and secure it against
uncontrolled turning on.
In order to clean the fan it is necessary to:
- disassemble the device (remove the panel, housing, rotor)
- wash all parts with a damp cloth, taking care not to wet
engine
- never use water at temperatures higher than 60oC,
gasoline, benzene, thinner or any other organic solvent
- dry all elements thoroughly
- re-install the fan
- connect the fan to power supply
Wiring diagram
Device versions
1) With time switch (models with "T" index)
The fan with timer switches on when it receives power.
Then the device will continue operation for 1 –30 minutes
(depending on the settings).
The time can be adjusted with appropriate knob.
2) With humidity sensor (models with "H" index)
The fan with the humidity sensor switches on automatically
when the humidity level in the room exceeds the set level,
then it works until the level falls below the set level and
subsequently continues operation according to the time
set on the time switch (so-called delay time). Timer settings
can be adjusted in the range of 1 - 30 minutes
and the relative humidity sensor in the range of 60 - 90%.
The values (delay time or humidity level) can be adjusted
with appropriate knobs.
3) With motion sensor (models "MS" index)
The fan with the motion detection sensor switches
on automatically when the sensor detects motion
in the sensor's operating area (semicircle with the set
diameter), then it works until the movement stops
and subsequently continues operation according
to the time set on the time switch (so-called delay time).
Timer settings can be adjusted in the range of 1 - 30
minutes and the range of the motion sensor from 0.5 m
to 8 m.
The values (delay time or range of the motion sensor) can
be adjusted with appropriate knobs.
Terms of warranty
I. Reventon Group Sp. z o.o. [Ltd.] is the supplier of the fans
and provides 24-month warranty period for VELO and VELO
Silver series.
II. The terms of warranty are valid from purchasing
the device (the date issuing a document confirming
the purchase of the device) but not further than 30 (thirty)
months from leaving the supplier’s warehouse.
III. The claim will be considered only if the document
confirming the purchase (eg. copy of the invoice)
and description of the fault is provided.
IV. The supplier is committed to consider the claim within
14 working days since the date of reporting (i. e. day when
documents given in point III are provided).
V. Under the guarantee the supplier provides a repairment,
replacement or refund for the defective device within
a specified time limit.
VI. Warranty does not cover mechanical damage,
degradation of the quality related with time passing
and defects resulting from improper exploitation /
maintenance or arbitrary repairs and modifications.
If there is any of the above, you will be charged
for transport and / or repairs.
VII. The supplier do not cover the dismantling / mantling
costs.
VIII. All correspondence should be send to the following
address: Reventon Group Sp. z o.o., 556 Wyzwolenia
Street, 43-340 Kozy, Poland or on e-mail:
[e-mail].
The supplier Reventon Group Sp. z o. o. reserves the rights
to make changes in the technical data.