D
C
A
A
B
C
D
42 1
3
32
4
B
NOTICE TO PERSONS RECEIVING THE DRAWING AND/OR TECHNICAL INFORMATION:
Yale Security INC. claims proprietry rights to the material
disclosed hereon. This drawing and/or technical information
is issued in confidence for engineering information only and
may not be reproduced or used to manufacture anything shown
or referred to hereon without direct written permission from
Yale Security Inc. to the user.
This drawing an /or technical information is the property of
Yale Security Inc. and is loaned for mutual assistance to be
returned when its purpose has been served.
REVDRAWING NO.
SHEET 1 of 5
THIS IS A Pro/E GENERATED DRAWING/ALL CHANGES TO THIS DRAWING MUST BE MADE AT THE Pro/E SYSTEM.
63
1-1/4±1/16
9/16±1/16
5.750
4.250
.175
.250
.250
3.750
5.250
R.250
Surface / Finish:
DRAWING
COMPLIES WITH
ANSI Y14.5M -
1994
Material:
Heat Treatment:
UNLESS OTHERWISE SPECIFIED:
N/A
XXX
TWO PLACE DECIMAL 0.01
THREE PLACE DECIMAL 0.005
ANGULAR: 0.5
Depth:
XXX
FRACTIONAL 1/64 SURFACE FINISH
Volume: Weight: Surface Area:
Created(YYYY-MM-DD)
Designed by: Drawn by: Scale:
Dwg.Size
Projection:
2017-01-19 BDH BDH 1.500 C
Third Angle
ASSA ABLOY DOOR CONTROL
ASSY - WIRELESS INTERFACE MODULE
Alternate ID:
ADA1028W02PC00
Yale Security Inc
Monroe DC
Document ID: Rev:
2
ADA1028W02PC00 2
THIS SYMBOL INDICATES ADDITIONS, CHANGES, AND DELETIONS
THIS SYMBOL INDENTIFIES GENERAL NOTE NUMBER
THIS SYMBOL INDICATES CRITICAL DIMENSION
REVISION
ZONE LTR DESCRIPTION DATE ENG
1 ECN 16-0026 INITIAL RELEASE Jan-19-17 BDH
2 ECN 16-0026 UPDATED R48 Jan-19-17 BDH
Inputs/Outputs:
1. Power input – Gnd (19), 12 OR 24VDC (18)
2. Output to Operator – Sig (5), Ground (6), 24VDC (7)
3. INSIDE switch Input – (1/2)
4. OUTSIDE Switch Input – (3/4)
5. Switch to manually transmit RF signal to operator (SW3) with LED5
6. Switch to learn/reset INSIDE RF button (SW1) with LED3
7. Switch to learn/reset OUTSIDE RF button (SW2) with LED4
8. RF signal from INSIDE activate button (RF1)
9. RF signal from OUTSIDE activation button (RF2)
10. Fire panel - (8/9)
11. Access Control – In, COM, Out (10/11/12)
12. Lock connector – NO, COM, NC (13/14/15) with LED2
13. Signal Delay selector switch (SW4)
14. Sensor – (GND, 24VDC, COM, OCC, SSS, ODS) – (20/21/22/23/24/25)
15. Antenna – the interface module will have an antenna for receiving signals.
(The antenna can be extended outside the metal enclosure for improved signal reception.)
16. Audible beeper for programming feedback
17. Disable Outside Pushbutton (26/27)
NOTES:
1. SEE SHEETS 2-5 FOR SCHEMATIC
2. REFER TO ADA1028W02PC00_BOM.PDF FOR BILL OF MATERIAL
3. REFER TO ADA1028W02PC00_TEST_PROCEESURE.XLS FOR
TEST PROCEEDURE.
ON SHORE TECHNOLOGY
P/N OSTYK42102030
LED1
LED 3
LED2
LED 4
LED 5
1
2
34
5
6
7
8
9
10
11
12
13
14
15
16
17
19 18
20
21
22
23 25
SW1
SW2
SW3
SW4
24
DIGIKEY P/N 609-3900-ND
26
27
18 GA SOLID
WIRE JUMPER
COLOR BLACK
18 GA SOLID
WIRE JUMPER
COLOR BLACK
ANTENNA WIRE - 18IN 24AWG
STRANDED WIRE WITH BLACK
PVC INSULATION.
WRAP AS SHOWN
FCC LABEL - P/N ADA1028W06LB00
REAR VIEW
(ANTENNA WIRE
NOT SHOWN)
FCC LABEL PLACEMENT
SCALE 1.000
