RF Elements StationBox Mikro User manual

STEP 1 Open the Bottom Cover
Release the lock.
Release the lock using thumb, check if the lock stays in released position.
Lock is released. Release one side.
Slightly release one side of the bottom cover, then another side. Remove the cover.
Lock is locked. Release another side. Release the bottom cover.
Good grip is very helpful - dry hands will
make the operation way easier.
Make sure you say„Aloha“ :)
Practice – soon, you will be able to do
the trick in a second.
STEP 2 Release the Base panel
How it works?
To perfom this step, both side-locks
of Auto-Lock system should be
released prior to pulling the Base
Panel out of the Top Cover.
There are two tricks how to do it:
A. Left-Right Way
Press the lock on one side of the box
and slightly pull out the Base Panel so
the lock does not lock again and stays
unlocked even when you release your
hand. Press the lock on the another
side and pull the Base panel out
completely.
B.„Aloha“ :) Way
You can do the same in one step using
only one hand. This is very useful
when outdoor, on the roof, ladder etc.
Grip the base panel with middle three
fingers of your hand. While pushing
the thumb and pinky to release both
side locks, pull out the Base Panel.
Release another side-lock.Release one side-lock. Pull out the Base Panel.
Grip the Base Panel. Push. Pull out the Base Panel.
1 How To Open StationBox® Mikro
Quick Installation Guide StationBox® Mikro
www.rfelements.com
®

Connect the pigtails to antenna.
A B
Line up the Ports in the openings.
Insert the board. First line up the ports,
then snap the board in the position.
Connect the pigtails to the board/radio.
Connect the opposite side of the
pigtail(s) to the radio/board connectors.
Snap the Board to the position.
In case the board locks (close to the each of positioning pins) are too though, no need
for bigger hammer. Gently release the side locks with your fingers so board sits to the
pre molded position smoothly.
Remove all transport protecting tapes
and similar items from the board. First
check the setup of ports on your board.
If you need to open some of premolded
positions on the Base Panel, please do so
prior to inserting the board. Connect the
pigtail(s). Antenna side are both MMCX.
Setup of ports:
5GHz version
Port A – Vertical Polarization
Port B – Horizontal Polarization
First release rear side locks which
are holding board on the pins using
your fingers and lift the board from
the postion. Release front side locks
and by lifting board release the board
from the Base Panel. Disconnect the
pigtail(s).
Release the side locks.Board lock too though. Board locked OK.
Also make sure you mind the pigtails
path is free in space between the Board
and the Base Panel.
How To Release the Board
Lift the board.Release the front position.Release the rear position. Disconnect pigtails from the Board. Disconnect Pigtails from the Antenna.
Done :)
How To Insert the Board
2 Board Installation
Quick Installation Guide StationBox® Mikro
www.rfelements.com
®

STEP 1 Insert the Base Panel
Insert the Base Panel Lock. Incorrect fit.Correct fit.
When inserting the Base Panel, make sure it fits correctly between the sliding rails
premolded in the interior of Top Cover.
When locking the Base Panel, push on the both side-locks simultaneously. Alternatively, you can push on the middle part of the
Base Panel surrounding the Bottom Cover Lock. Do not push the Base Panel in the area of ports!
Correct setup.
Make sure you direct antenna to the front of the StationBox Mikro.
Make sure you direct antenna to the front of the StationBox Mikro.
Insert the Base Panel to the Top Cover and push it. You should hear loud„click!“ sound.
Wrong setup. Correct push.Correct push. Incorrect Push.
Quick Installation Guide StationBox® Mikro
www.rfelements.com
3 How To Close the StationBox® Mikro
Make sure you connected all cables
and opened enough premolded
positions in the Bottom Cover to lead
cables from the closed device. Make
sure the Bottom Cover is sliding in the
premolded rails.
STEP 2 Close the Bottom Cover
Correct fit – Bottom Cover.Slide the bottom cover to the Top
cover.
Bottom Cover cable positions Correct Push. Bottom Cover Locked.
®

Push-and-Click the Holder.
You can visually check if both parts
of the lock went through.
Left Lock - Correct, Right Lock - Wrong. Correct fit. Incorrect fit.
NanoBracket®+ StationBox® Mikro.
We recommend NanoBracket Universal
to achieve excellent mounting capability.
www.nanobracket.info
4 How To Attach Holder
RF elements s.r.o., Jasenovská 2528, 066 01 Humenné, Slovakia
Phone: [phone]
[email protected]
www.rfelements.com
Quick Installation Guide StationBox® Mikro
www.rfelements.com
No rocket science at all
Push-and-Click the Holder in the
premolded position on the Top Cover.
Make sure You hear ´click!´ sound.
®