RGBLE M01405 User manual

Stock Code 873117 en.rgble.com 400-1661-021
P/N:M01405
18Gbps 4K@60Hz
4x4 HDMI HDBT
Matrix System with Scaler
User Manual
VER 1.0

Stock Code 873117 en.rgble.com 400-1661-021
P/N:M01405
Thank you for purchasing RGBLE product
For optimum performance and safety, please read these instructions carefully before
connecting, operating or adjusting this product. Please keep this manual for future reference.
Surge protection device recommended
This product contains sensitive electrical components that may be damaged by electrical
spikes, surges, electric shock, lighting strikes, etc. Use of surge protection systems is highly
recommended in order to protect and extend the life of your equipment.
Table of Contents
1. Introduction.............................................................................................2
2.Features...................................................................................................2
3. Package Contents...................................................................................3
4. Specifications..........................................................................................3
5. Operation Controls and Functions...........................................................5
5.1. Matrix Panel........................................................................................5
5.2. HDBT Receiver Panel.........................................................................7
6. IR Remote................................................................................................8
7. IR Control System....................................................................................8
8. IR Cable Pin Assignment........................................................................10
9. EDID Management..................................................................................11
10. Web GUI User Guide.............................................................................12
11. RS-232 Control Command.....................................................................20
12. Application Example...............................................................................27

Stock Code 873117 en.rgble.com 400-1661-021
P/N:M01405
4x4 HDMI HDBT Matrix System with Scaler
18Gbps 4Kx2K@60Hz
1. Introduction
The 18Gbps 4x4 HDMI HDBT Matrix System with Scaler can connect four HDMI sources to
eight displays. It features four HDMI outputs and each HDMI output is mirrored to provide a
CAT-Cable output which runs simultaneously. HDBT output can extend video transmission
distance up to 492ft / 150m via a single Cat 5e/6/7 cable and the resolution is up to
4K2K@60Hz 4:4:4. Audio de-embedded to analog and coaxial audio is supported. Each HDMI
output supports 4K2K to 1080P downscale independently.
The product supports IR matrix. The IR signal is one-to-one control at the Matrix end, but the IR
signal follows HDMI video channel at the HDBT Receiver end. The product provides an intuitive
set of front panel with OLED screen and supports control via front panel buttons, IR remote, RS-
232, LAN, and Web GUI.
2. Features
◆HDMI 2.0b, HDCP 2.2 and HDCP 1.x compliant
◆Video resolution up to 4K2K@60Hz (YUV 4:4:4) on all HDMI & HDBT ports
◆4 HDMI inputs, 4 HDMI & HDBT mirrored outputs
◆HDMI ports transmit 18Gbps lossless uncompressed video bandwidth
◆Support 18Gbps lossless compressed HDBT signal transmission
◆Support 4K->1080P Down Scaler for each output port
◆HDR, HDR10, HDR10+, Dolby Vision, HLG are supported
◆HDBT output can extend video transmission distance up to 492ft / 150m for 1080P
◆or 394ft / 120m for 4K2K via a single Cat 5e/6/7 cable
◆HDMI audio pass-through up to 7.1CH HD audio (LPCM, Dolby TrueHD and DTS-HD
◆Master Audio)
◆Support IR matrix
◆Audio de-embedded is supported via analog and coax ports
◆Advanced EDID management and CEC control are supported
◆24V POC on all HDBT ports
◆1U rack mounted design with front panel OLED display
◆Control via front panel buttons, IR remote, RS-232, LAN and Web GUI

Stock Code 873117 en.rgble.com 400-1661-021
P/N:M01405
3. Package Contents
①1 x 18Gbps 4x4 HDBT(150M) Matrix
②4 x HDBT Receiver
③1 x Matrix IR Remote
④1 x 100~240V AC 50/60Hz Power cable
⑤1 x RS-232 serial cable (1.5 meters, male to female head)
⑥4 x 3-pin Phoenix Connector & 4 x 5-pin Phoenix Connector
⑦5 x IR Blaster cable (1.5 meters)
⑧5 x IR Receiver cable (1.5 meters)
⑨10 x Mounting Ear (Matrix and Receiver)
⑩1x User Manual
4. Specifications
Technical
HDMI Compliance
HDMI 2.0b
HDCP Compliant
HDCP 2.2 and HDCP 1.x
Video Bandwidth
18Gbps
Video Resolution
Up to 4K2K@50/60Hz (4:4:4)
Color Space
RGB 4:4:4, YCbCr 4:4:4/4:2:2/4:2:0
Color Depth
8-bit, 10-bit, 12-bit (1080p@60Hz)
8-bit (4K2K@60Hz YUV4:4:4)
8-bit,10-bit,12-bit (4K2K@60Hz YCbCr 4:2:2/4:2:0)
HDR
HDR10, HDR10+, Dolby Vision, HLG
HDMI Audio Formats
LPCM 2.0/2.1/5.1/6.1/7.1, Dolby Digital, Dolby TrueHD,
Dolby Digital Plus(DD+), DTS-ES, DTS HD Master,
DTS HD-HRA, DTS-X
Coax Audio Formats
PCM 2.0, Dolby Digital / Plus, DTS 2.0/5.1
Analog Balanced
Audio Formats
PCM2.0CH
Vmax
2Vrms
SNR
＞80dB
THD+N Ratio
＜0.1%（V_max）0.001%~0.01%（V_best）
Crosstalk
＞80dB
Frequency Response
20Hz~20kHz ±0.5dB
ESD Protection
Human-body Model:
±8kV (Air-gap discharge), ±4kV (Contact discharge)

Stock Code 873117 en.rgble.com 400-1661-021
P/N:M01405
Connection
Matrix
Inputs: 4 x HDMI Type A [19-pin female]
Outputs: 4 x HDMI Type A [19-pin female]
4 × HDBT port [RJ45]
4 ×Coaxial audio [3.5mm Stereo Mini-jack]
4 ×balanced analog audio [5-pin Phoenix connector]
Controls: 5 x IR IN [3.5mm Stereo Mini-jack]
5 x IR OUT [3.5mm Stereo Mini-jack]
1 ×TCP/IP [RJ45]
1 ×RS-232 [D-Sub 9]
HDBT Receiver
Input: 1 x HDBT IN [RJ45, 8-pin female]
Outputs: 1 x HDMI Type A [19-pin female]
1 x AUDIO OUT [3.5mm Stereo Mini-jack]
Controls: 1 x IR IN [3.5mm Stereo Mini-jack]
1 x IR OUT [3.5mm Stereo Mini-jack]
1 x RS-232 [3-pin Phoenix connector]
General
Housing
Metal Enclosure
Color
Black
Dimensions
Matrix: 440mm (W) ×200mm (D) ×44.5mm (H)
Receiver: 140mm (W) x 65mm (W) x 18mm (W)
Weight
Matrix: 3.1Kg, Receiver: 155g
Power Supply
AC 100 - 240V 50/60Hz
Power Consumption
60W (Max)
Operating Temperature
0°C ~ 40°C / 32°F ~ 104°F
Storage Temperature
-20°C ~ 60°C / -4°F ~ 140°F
Relative Humidity
20~90% RH (non-condensing)
Resolution / Distance
4K60 - Feet / Meters
1080P60 - Feet / Meters
CAT5e/6/7
394ft / 120M
492ft / 150M
Resolution /
Cable Length
4K60 –
Feet / Meters
4K30 –
Feet / Meters
1080P60 –
Feet / Meters
HDMI IN / OUT
16ft / 5M
32ft / 10M
50ft / 15M
The use of “Premium High-Speed HDMI” cable is highly recommended.

Stock Code 873117 en.rgble.com 400-1661-021
P/N:M01405
5. Operation Controls and Functions
5.1 Matrix Panel
Front Panel
Name
Function Description
OLED screen
Display matrix switching status, input / output port, EDID, Baud rate, IP
Address.
Power LED
The LED will illuminate in green when the product is working normally, and
red when the product is on standby.
OUTPUT /
INPUT buttons
You need to press an output button (1~4) firstly and then press an input
button (1~4) to select the corresponding input source for the output port.
MENU / ENTER
/ UP /DOWN
①EDID setting: On the initial OLED display screen, press “MENU” button
to enter “Select EDID” interface, press “UP/DOWN” button to select the
required EDID, and press the “ENTER” button to enter “Copy to Input:”
interface. Then press “UP/DOWN” button to select the input port you
need to set, and press “ENTER” button again to confirm.
②Baud rate setting: On the initial OLED display screen, press “MENU”
button twice to enter “SELECT BAUD” interface, and press “UP/DOWN”
button to select the required Baud rate, finally press the “ENTER” button
to confirm the setting.
③IP Address Check: On the initial OLED display screen, press “MENU”
button three times to enter the IP interface and check the current IP
address, then press “UP/DOWN” button to switch DHCP ON/OFF, finally
press the “ENTER” button to confirm the setting. Pressing the “MENU”
button again will return to the initial OLED display status.
POWER button
Press and hold the POWER button for 3 seconds to enter the standby mode,
then press the button again to wake up the device.
IR Window
IR receiver window, it only receives the IR remote signal from this product.
LOCK button
Press the LOCK button to lock front panel buttons (Except the power button);
Press the button again to unlock.

Stock Code 873117 en.rgble.com 400-1661-021
P/N:M01405
Rear Panel
Name
Function Description
IR IN (1/2/3/4/ALL) ports
Connect to IR receiver cable, the IR receive signal will emit to the
“IR OUT” port of the HDBT Receiver.
IR OUT (1/2/3/4/ALL) ports
Connect to IR blaster cable, the IR emit signal is from the“IR IN”
port of the HDBT Receiver.
AUDIO OUT (1-4) ports
4 groups of coaxial and balanced analog audio mirrored output
ports. AUDIO OUT (1-4) follows the video output of OUTPUT (1-4)
ports.
GND
Connect the housing to the ground.
POWER input
Power port: Connect to 100~240V AC 50/60Hz power cable.
Power switch: Press the switch to turn on/off the power.
OUTPUT (1-4) ports
HDMI output ports, connect to HDMI display device such as TV or
monitor with an HDMI cable.
HDBT mirrored output ports, connect to HDBT Receiver via CAT
cable.
INPUT (1-4) ports
HDMI input ports, connect to HDMI source device such as DVD or
PS4 with an HDMI cable.
➑
CONTROL ports
TCP/IP: The link port for TCP/IP control. Connect to an active
Ethernet link with an RJ45 cable.
RS-232: Command control port. Connect to a PC or control
system with a D-Sub 9-pin cable to control the Matrix.
Data Signal
Indicator Lamp
▪Illuminating: HDMI signal with
HDCP.
▪Flashing: HDMI signal
without HDCP.
▪Dark: No HDMI signal.
Connection Signal
Indicator Lamp
▪Illuminating: Matrix and HDBT
Receiver are in good connection
status.
▪Flashing: Matrix and HDBT
Receiver are in poor connection
status.
▪Dark: Matrix and HDBT
Receiver are not connected.
Video (OUT)

Stock Code 873117 en.rgble.com 400-1661-021
P/N:M01405
5.2 Receiver Panel ports
Number
Name
Function descriptions
Power LED
Red LED indicates that the receiver is powered on.
DC 24V
DC 24V/1A power supply input port.
Note that the extender supports POC function, it means that
either transmitter or receiver is powered on by 24V/1A power
adapter, the other one doesn’t need power supply.
HDBT IN
RJ45 connector for connecting the HDBT OUT port of
transmitter with a CAT 5e/6 cable.
HDMI OUT
HDMI output for display.
AUDIO OUT
3.5mm stereo connector for analog audio output.
IR IN
IR input port for receiving the signal of IR remote.
IR OUT
IR output port for control of display device. This IR output
signal is from the IR IN port of transmitter.
➑
RS-232
3-pin Phoenix connector for RS-232 command transmission.
The RS-232 command will pass-through from transmitter to
receiver or from receiver to transmitter.
➒
Connection
Signal Indicator
Lamp
Illuminate: The Transmitter and Receiver are in good
connections status.
Flashing: The Transmitter and Receiver are in poor
connections status.
Dark: The Transmitter and Receiver are not connected.
➓
Data Signal
Indicator Lamp
Illuminate: HDMI signal with HDCP.
Flashing: HDMI signal without HDCP.
Dark: No HDMI signal.

Stock Code 873117 en.rgble.com 400-1661-021
P/N:M01405
6. IR Remote
Power on or Standby: Power on the Matrix or set it to
standby mode.
Output1：Press 1/2/3/4 button to select input source to
HDMI OUTPUT1.
Output2：Press 1/2/3/4 button to select input source to
HDMI OUTPUT2.
Output3：Press 1/2/3/4 button to select input source to
HDMI OUTPUT3.
Output4：Press 1/2/3/4 button to select input source to
HDMI OUTPUT4.
Select the previous or next input source button.
7. IR Control System
The product is not only a matrix switch but also an extender. It supports bi-directional IR
control. When Matrix is connected to HDBT Receiver through Cat 5e/6/7 cable, you can
control remote display device (HDBT) or input source device (Matrix) through IR signal
transmission. But you must note that the IR signal transmission method is different from the
method from Matrix (local) to HDBT Receiver (remote) and from HDBT Receiver
(remote) to Matrix (local).
At the Matrix end (Local end): the IR signal is one-to-one transmission. For example, the
IR IN 1 port signal of the Matrix will emit to IR OUT port of the HDBT Receiver 1, and the
IR IN 3 port signals of the Matrix will emit to IR OUT port of the HDBT Receiver 3. It doesn’t
follow the video switch to change. IR IN ALL port signal of the Matrix will emit to all IR OUT ports
of HDBT receivers simultaneously. Please see the following connection diagram.

Stock Code 873117 en.rgble.com 400-1661-021
P/N:M01405
Figure 1: IR connection diagram (Matrix end)
At HDBT receiver (Remote end): IR signal follows video switch to change. For example,
the HDMI output signal on the HDBT Receiver 1 is from the HDMI INPUT 2 port, so IR
input signal of the HDBT Receiver 1 will emit to IR OUT 2 port of the Matrix. The HDMI
output signal on the HDBT Receiver 3 is from the HDMI INPUT 4 port. Then, IR input
signal of the HDBT Receiver 3 will emit to IR OUT 4 port of the Matrix etc. Any of
HDBT Receiver’s IR IN signal can output from IR OUT ALL port of the Matrix and the
IR OUT ALL signal of the Matrix depends on your IR remote of source device. Please see
the following connection diagram.