RH Baby&child JAMESON CONVERSION CRIB User manual

11
/
1/11

2/11
IMPORTANT SAFETY INFORMATION FOR CRIBS
WARNING: Infants can suffocate on soft bedding. Never add a pillow or
comforter. Never place additional padding under an infant.
WARNING: Failure to follow these warnings and the assembly instructions
could result in serious injury or death.
·To reduce the risk of SIDS, pediatricians recommend healthy infants to be placed on their backs to
sleep, unless otherwise approved by your physician.
Strangulation Hazard:
·Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such as
hood strings or pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
·To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on
loose fasteners.
·DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Fall Hazard:
·When a child is able to pull to a standing position, set mattress to lowest position and remove
bumper pads, large toys and other objects that could serve as steps for climbing out.
·When child is able to climb out or reaches the height of 35" (89cm), the crib shall no longer be used,
and the child should be placed in a youth or regular bed.
·Check this product for damaged hardware, loose joints, missing parts or sharp edges before and
after assembly and frequently during use. Securely tighten loose bolts and other fasteners. DO NOT
use crib if any parts are missing, damaged or broken. Contact customer service at 1-800-762-1751
for replacement parts and instructional literature if needed.
·DO NOT substitute parts.
·DO NOT use a water mattress with this crib.
·If refinishing, use a non-toxic finish specified for children’s products.
·Follow warnings on all products in a crib.
·Never use plastic shopping bags or other plastic film as mattress covers because they can cause
suffocation.
·Infants can suffocate in gaps between crib sides and a mattress that is too small.

3/11
IMPORTANT SAFETY INFORMATION FOR CRIBS
CAUTION: ANY MATTRESS USED IN THIS CRIB SHALL BE
AT LEAST 27 1/4" X 51 5/8" WITH A THICKNESS
NOT EXCEEDING 6".
WARNING
Do not use this crib if you cannot exactly follow the instructions
provided.
Do not use this crib for a child who can climb out of it or who is
taller than 35" (89cm).
Do not place in or near the crib any cord, strap or similar item that
could become wrapped around a child's neck.
Do not place this crib near a window or patio door where a child
could reach the cord of a blind or curtain and the strangled.
Check this crib regularly before using it, and do not use if any part
is loose or missing or if there are any signs of damage.
Do not substitute parts. Contact the manufacturer if replacement
parts or additional instructions are needed.
Children can suffocate on soft bedding. Do not place pillows,
comforters or soft mattresses in this crib.
Use a mattress that is no thicker than 15cm in height and, when it
is pushed firmly against any side of this crib, it does not leave a
gap of more than 3cm between the mattress and any part of any
other side of the crib.

4/11
IMPORTANT SAFETY INFORMATION FOR TODDLER AND DAYBEDS
·The mattress intended for use on the bed shall be a full-size crib
mattress having minimum dimensions of 51 5/8" (1310mm) in
length, 27 1/4" (690mm) in width and 4" (100mm) in thickness, not
exceeding 6" (150mm) in thickness.
·DO NOT place bed near windows where cords from blinds or
drapes may strangle a child.
·DO NOT place items with a string, cord, or ribbon around a child’s
neck, such as hood strings or pacifier cords.
·DO NOT suspend strings over a toddler bed for any pacifier cords.
·A child using the toddler or daybed shall be at least 15 months of
age and shall not weigh more than 50 lbs (22.7kgs).
WARNING: ENTRAPMENT / STRANGULATION HAZARD
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use bed with children under 15 months of age.
NEVER place bed near windows where cords from blinds or drapes
may strangle a child.

PARTS IDENTIFICATION
FRONT RAIL
SIDE RAIL PANEL
HEAD BOARD
MATTRESS SUPPORT
For ease of identification, all parts are labeled to correspond
to the Step number in which the part is used.
Step 1 Side frame and head board assembly (Page 6)
Step 2 Mattress support arm assembly
Stabilizer rail assembly
Mattress height adjustment (Page 7)
Step 3 Support slat & side rail panel assembly (Page 8)
Step 4 Front rail assembly (Page 9)
Step 5 Toddler rail assembly (Page 10)
Step 6 Metal bed frame assembly (Page 11)
5/11

STEP 1
HEAD BOARD & SIDE RAIL PANEL
ASSEMBLY
HARDWARE NEEDED FOR STEP 1
STEP 1.1
Bring the head board and the side panel in upright
position.
NOTE:
On both side ends of the head board are holes for
the bolt to pass through that corresponds on the
holes located on both side ends of the side rail
panel with pre-installed insert nut.
STEP 1.2
Insert the bolt in each hole and tighten with Allen
wrench provided. See DETAIL A.
DETAIL A
A
(AA)
(AA) 1/4" x 2 1/2" Allen Bolt = 4 pcs
Lock Washer = 4 pcs
Plain Washer = 4 pcs
Allen Wrench = 1 pc
Allen bolt (AA)
Lock washer
Plain washer
6/11
Allen Wrench

Lock
Washer
B
C
STEP 2
MATTRESS SUPPORT ARM ASSEMBLY
STABILIZER RAIL ASSEMBLY
MATTRESS HEIGHT ADJUSTMENT
DETAIL B
DETAIL C
Hex Nut
Plain
Washer
Allen Bolt (BB)
Allen Wrench
Open Wrech
Hex Nut
Lock Washer
Plain Washer
Mattress Support
Stabilizer Rail
HARDWARE NEEDED FOR STEP 2
(BB) 1/4" x 1 1/4" Allen Bolt = 8 pcs
Allen Wrench = 1 pc
Lock Washer = 8 pcs
Plain Washer = 8 pcs
Hex Nut = 8 pcs
Allen Bolt (BB) Allen Bolt (BB)
Allen Bolt (BB)
Allen Bolt (BB)
11 X 70
Open Wrench = 1 pc
STEP 2.1
Lay mattress support flat with stabilizer rail on each side.
NOTE:
On each end of the arm of the mattress support, there is a hole for the
bolt to pass through that corresponds to the holes located in the frame
of the mattress support.
STEP 2.2
Insert the bolt into the desired hole of the frame through the hole on the
arm support. Fasten the bolt with plain washer, lock washers &
hexagonal nut provided. Repeat procedure on other arms of the
mattress support. See DETAIL B.
WARNING:
Set the mattress support to the desired height by adjusting the support
arms. The mattress support should be at its highest setting for
newborns, then adjusted to the lower positions as the child grows and
becomes mobile. Once the child is able to stand, the mattress support
should be at its lowest position.
STEP 2.3
Install the stabilizer rail at ends of the arm support, as illustrated in
DETAIL C.
7/11
Allen Wrench

STEP 3
STABILIZER RAIL INTO SIDE RAIL PANEL
ASSEMBLY
DETAIL D
DETAIL F
STEP 3.1
On inside face of both side panels are pre-installed metal
brackets, designed to hold the stabilizer rails. Set both ends of
the stabilizer rails into brackets, as illustrated in DETAIL D.
STEP 3.2
Once the stabilizer rails are set, gently tilt the crib as
illustrated in DETAIL E, then fasten the stabilizer rails with
bolt together with plain washer and lock washer provided, as
illustrated in DETAIL F.
DETAIL E
HARDWARE NEEDED FOR STEP 3
(CC) 1/4" x 13/16 " Allen Bolt = 4 pcs
Lock Washer = 4 pcs
Plain Washer = 4 pcs
Allen Wrench = 1 pc
8/11

STEP 4
FRONT RAIL ASSEMBLY
DETAIL G
STEP 4.1
On both ends of the front rail are holes for the bolt to pass through
and pre-installed wooden dowels that correspond to the holes on
the posts for both side rail panels with pre-installed nuts and
pre-bored holes for the wooden dowels. Align and insert the
wooden dowel on the lower front rail into the lower holes of both
side rail panels, then engage the top bolt in each hole and tighten
with Allen wrench provided, as in DETAIL G & DETAIL H.
After assembly re-tighten all bolts to a snug fit. DO NOT OVER
TIGHTEN.
HARDWARE NEEDED FOR STEP 4
DETAIL H
H
Wooden Dowel
H
G
G
G
G
(DD) 1/4" x 1 3/4" Allen Bolt = 4 pcs
Allen Wrench = 1 pc
Lock Washer = 4 pcs
Plain Washer = 4 pcs
Allen bolt (DD)
Lock washer
Plain washer
9/11
Locator Slot

STEP 5
TODDLER RAIL ASSEMBLY
STEP 5.1
Remove the front rail panel of the crib by loosening all the bolts
installed.
STEP 5.2
Gently tilt the crib and release the bolts underneath the metal
brackets holding the stabilizer rails.
STEP 5.3
Gently remove the mattress support and slightly loosen the bolt
at the back of the headboard that enough to set the toddler rail
in-between side rail panel.
NOTE: Fill the holes located on the top of both side rail panel by
inserting bolt (EE) provided.
STEP 5.4
On inside face of both side rail panels there is a cavity for the
hook and a hole for the Allen bolt to pass through, which
corresponds to the hooks on both ends of the toddler rail and
hole with pre-installed nut. Align and insert the hook of the
toddler rail into the cavity of the side rail panel, then engage
Allen head bolt in the hole and tighten with Allen wrench
provided. See DETAIL I.
-NOTE: If mattress support is not in the lowest position, unscrew
mattress support bolts and move the lowest position.
STEP 5.5
Repeat step 3. Installation of stabilizer rails into the side panel
(DETAIL J).
After assembly, re-tighten all bolts to a snug fit.
HARDWARE FOR STEP 5
(PACKED INSIDE TODDLER RAIL BOX)
EE
DETAIL I
I
ALLEN
WRENCH
ALLEN HEAD
BOLT (FF)
METAL
HOOK
DETAIL J
Allen bolt (FF)
EE
(EE) 1/4" x 1/2" Allen Bolt = 2 pcs
(FF) 1/4" x 2 1/2" Allen Bolt = 2 pcs
Allen Wrench = 1 pc
Lock Washer = 2 pcs
Plain Washer = 2 pcs
Lock washer
Plain washer
10/11

STEP 6
METAL BED FRAME ASSEMBLY
STEP 6.1
Loose all the bolts in crib to
disassemble the crib.
STEP 6.2
Bring the Heaboard in upright position.
STEP 6.3
On the bottom of the headboard there
are holes for the bolt to pass through
that correspond to the holes on the
metal bed frame. Attach the Metal bed
frame to the Headboard by using Allen
bolts (GG) with lock washers and plain
washers into the sleeve nut on the
other side. See DETAIL K.
11/11
HARDWARE NEEDED FOR STEP 6
(GG) M6 x 50mm Allen Bolt = 4 pcs
Lock Washers 1/4" = 4 pcs
Plain Washers 1/4" = 4 pcs Allen Wrench = 2 pcs
Sleeve nut M6 = 4 pcs
DETAIL K