RHINO 34-873 User manual

MOD
RHINO AIR HOCKEY
EL NUMBER 34-873:
INSTRUCTION MANUAL

1
#36
#20
#1 #2 #3
#8#7
#6#5#4
#9 #10
#15#14
#11 #12
#13 #18
#33#32
#38 #39 #40 #41 #42
#31
#17#16
#19 #21 #23#22 #24
#25 #26 #28#27 #29 #30
#34 #35
#37
Apron Corner End Panel End Apron With
4 Pieces 1 Pieces
Left Leg Panel
2 Pieces
Left Leg Base
2 Pieces
8X19mm Washer
32 Pieces
6.5X15mm Washer
28 Pieces
8mm Hex Nut
12 Pieces
4X18mm Round
Head Screw
96 Pieces
4X12mm Round
4X15mm Round
Head Screw
60 Pieces
Electronic Scorer
-Base
1 Piece
Scorer Support
2 Pieces
Top Puck Return Box
2 Pieces
Screw Cap
8 Pieces
Control Box
1 Piece Blower And Wire
1 Piece
Puck Return Tray
2 Pieces
Electronic Scorer
-Top
1 Piece
Pole Base-Outside
2 Pieces Pole Base-Inside
2 Pieces
Plastic Nut
2 Pieces
(Pre-Installed)
(Pre-Installed)
3X18mm Washer L Plastic Bracket U Plastic Bracket Puck Return Box-
Head Screw
14 Pieces 10 Pieces 12 Pieces 2 Pieces
Outside Puck Return Box-
2 Pieces
Inside
4X44.5mm Flat
Head Screw
20 Pieces
4X32mm Flat
Head Screw
Head Screw
8 Pieces
Right Leg Base
2 Pieces
8X38mm Hex Bolt 8X38mm Allen
8 Pieces Key Bolt
12 Pieces
6.5X35mm Allen
Key Bolt
24 Pieces
6.5X38mm Allen
Key Bolt
4 Pieces
Right Leg Panel
2 Pieces
Leg Support
Board-A
2 Pieces
Leg Support
Board-B
2 Pieces
Rounded Leg Panel
4 Pieces
Leg Side Panel
2 Pieces
Opening
1 Piece
Side Apron
2 Piece
Leg End Panel-
2 Pieces
Outside
Leg End Panel-
2 Pieces
Inside
#43
Goal Support Panel
2 Pieces
2 Pieces
Parts List

2
#A1 #A2 #A3
#A8#A7
#A6#A5#A4
#A9
Puck Catcher Wire 4mm Allen Key
2 Pieces 1 Piece
3 Pieces 1 Piece
Wrench Adapter
1 Piece
4 Pieces
Pusher Hockey Puck
4 Pieces
3 Pieces
1mm Shim
3mm Shim
2mm Shim
3 Pieces
Parts List
(Pre-Installed)

3
2
43
25
1
1
1
1
3
2
4
4
16
16
16 16
19
19
19
19
19
19
19 19
21
22
22
22
22
22
22
22
19
27
21
22
28
21
25
27
STEP:1
STEP:2
25
29
29
30
30
42
42
22
29
•Attach one Goal Support Panel (#43) to each End Apron (#2) using two Screws (#25) per Goal Support Panel.
•Attach four Plastic “U” Brackets (# 28) to both the Side Panel (#4) and (#3) using four Screws (#22) per U Bracket.
•Attach three “L” Bracket (#27) to both Side Aprons (#3 and 4) and two “L” Bracket (#27) to End Aprons (#2) using
• Attach two Plastic “U” Brackets (# 28) to both the End Aprons (#2) using four Screws (#22) per U Bracket. See Fig. 1A.
FIGURE 1A
FIGURE 1B
•Attach the Puck Return Trays (#42) to the End Aprons (#2) using two Screws (#25) per Puck Return Tray.
•Snap the Puck Return Boxes - Inside (#30) to the Puck Return Boxes - Outside (#29) as shown.
•Attach the Puck Return Boxes - Outside (#29) to the End Aprons (#2) using four Screws (#22) per Puck Return Box - Outside.
two Screws (#22) per Bracket. See Fig. 1B.
•Place the Side and End Aprons onto the cabinet so that the “U” Brackets fit around the cabinet supports. See Fig. 1A.
•Attach each “U” Bracket (#28) to the cabinet supports with one Bolt (#16) two Washers (#19) and one Nut (#21).
•Now attach the previously-installed “L” Brackets (#27) to the cabinet using two Screws (#22) per L Bracket.
•Attach each Apron Corner (#1) between one Side Apron and one End Apron using six Screws (#25) per Corner.

4
5
9
10
11
1
25
25
STEP:3
STEP:4
7
8
5
17
17
17
17
20
20
20
20
6
23
23
•Attatch two Rounded Leg Panels (#11) to one Leg End Panel - Outside (#5) using three Screws (#25)
•Attatch Leg Support Board - A (#9) and the Leg Support Board - B (#10) to the Rounded Leg Panels (#11) using three Screws (#25).
•Repeat the same for the other Leg End Panel.
•Attach one Left Leg Panel (#7) and one Right Leg Panel (#8) to one Leg End Panel - Inside (#6) using three Screws (#23) per Leg Panel.
•Attach the assembled Leg Panels and attach to one leg assembled in step3 using four Bolts (#17) and four Washers (#20). and then attach
the Leg End panel-inside (#6) to one leg assembled in step3 with four Bolts (#17) and four washers(#20).
•Repeat the same for the other leg assembly.

5
13
14
23 23
24
24
12
12
17
17
17
20
20
20
11
5
6
11 10
11
17
20
15
19
STEP:5
STEP:6
•Attach one Left (#13) and Right (#14) Leg Base to each side of one leg assembly using two Screws (#24) and two Screws (#23). See Figure 5.
•Repeat the same for the other leg assembly.
•Carefully turn the the leg assembly over and place it in the location where you will play. See Figure 5A.
FIGURE 5A
•Attach both Leg Side Panels (#12) between the leg assemblies using four Bolts (#17) and four Washers (#20) at the inside of each Leg Side
Panel.
•From underneath the table, attach the Cabinet to the leg assembly using four Washers (#19) and four Bolts (#15) at each end of the table.

6
26
32
31
32
32
35
37
35
37
37
26
34
25
25
33
34
34
25
33
18
20
26
A2
A2
18
20
18
20
38
38
37
STEP:7
•Attach the Electronic Scorer Base (#31) to the Electronic Scorer Top (#32) using six Screws (#26) at each side. See Figure 7A.
• Attach both Pole Bases - Inside (#34) to the side rails of the table using two Screws (#25) per Pole Base.See Figure 7B.
• Attach the Scorer Pole (#37) to the side rails of the Scorer Pole (#37) using two washers (#20) and two Bolts (#18) per Pole Base.
NOTE:Twist the Plastic Nut (#35) onto the Scorer Pole (#37).
•Insert the plug from the Electronic Scorer (#31/32) into the plug from the Scorer Pole (#37). See Figure 7C and Figure 7D.
•Thread the scorer wire from the Scorer Pole (#37) through the opening of the side rail.
•At this side of the table, attach one Pole Base - Outside (#33) to the Pole Base - Inside (#34) using four Screws (#26). Repeat the same for the
other side of the table using the other Scorer Pole (#37).
•Repeat the same at the other end of the Electronic Scorer.
FIGURE 7C
FIGURE 7D
FIGURE 7A
FIGURE 7B

7
39
40
36
STEP:8
A9
31
37 37
A1
40
32
•Aattach the Control Box (#40) to the End Apron with opening (#3) with two Screws (#36).
and Cover the screw holes on the pole Base-Owtside (#33) with 8pcs screw cap (#39).
BLOWER
Under side the ta ble
Adapter
Adapter
Home (Short
Sensor Wire)
Scorer Wire
Visitor (Long
Sensor Wire)
FI
Short Sensor Wire
Long Sensor Wire
Scorer Wire
Note: Make Sure the Short Sensor Wire
and Control Box on the same side.