RIA TECHNOLOGIES CIHSD Series User manual

High Speed Dome Camera
Operation Manual
CIHSD Series
RIA TECHNOLOGIES LIMITED
206 East Lampkin Street
Starkville, MS-39759, US
Toll Free [phone] Fax [phone]
Read manual carefully before camera installation and keep it for future reference.

Operation Manual of Intelligent Dome Camera
1
Notice:
Precautions:
1.Prior to operating this device, non-technicians must read this
manual thoroughly.
2.Remove the power supply before operating the device to avoid
damage caused by improper operation.
3.This dome device contains precision optical and electrical devices.
To prevent product damage heavy pressure, shock and other
incorrect operations should be avoided.
4.To avoid warranty invalidation please do not remove, or
disassemble any of the internal parts of this dome device. There are
no parts inside the device, which can be repaired by users.
5.All wiring and connections of this device should be conducted
strictly in accordance with wiring instructions. When necessary,
thunder-proof, surge-proof and other protecting measures should
be utilized.
6.Please do not use the product under situations exceeding specified
temperature, humidity, or power supply specifications.

Operation Manual of Intelligent Dome Camera
1
Content
Chapter 1 Product Overview................................................................................. 3
1.1 Performance instructions..................................................................... 3
1.2 Feature functions instruction................................................................ 3
Chapter 2 Basic Configuration ............................................................................. 6
2.1 Integrated connection of multiple domes ............................................. 6
2.2 Setting protocol and baud rate of dome device .................................... 7
2.3 Setting dome device address ................................................................ 8
2.4 Camera installation............................................................................... 9
2.5 Startup the power supply of the dome device ...................................... 9
2.6 Controller setting.................................................................................. 9
2.7 Start testing........................................................................................... 9
2.8 Complete the test (summary) ............................................................. 10
Chapter 3 Menu Setting........................................................................................11
3.1 Operation instructions .........................................................................11
3.2 Main menu ..........................................................................................11
3.3 Dome information .............................................................................. 12
3.4 Display options................................................................................... 12
3.4.1 Camera name setup ........................................................................ 12
3.5 Control options................................................................................... 13
3.5.1 Dome address stetup....................................................................... 13
3.5.2 Control option operation ................................................................ 13
3.6 Camera options(example: sony camera) ............................................ 14
3.6.1 Zoom and focus.............................................................................. 14
3.6.2 Camera exposure............................................................................ 14
3.6.3 Others ............................................................................................. 17
3.7 Function programming....................................................................... 17
3.7.1 Preset.............................................................................................. 17
3.7.2 Program vector scan. ...................................................................... 20
3.7.3 Pattern. ........................................................................................... 21

Operation Manual of Intelligent Dome Camera
2
3.7.4 Sector setup .................................................................................... 23
3.7.5 Mask zone ...................................................................................... 24
3.7.6 Mask color...................................................................................... 24
3.7.7 Motion. ........................................................................................... 25
3.8 System setup....................................................................................... 26
3.8.1 Clear memory................................................................................. 26
3.8.2 Restore def setting.......................................................................... 26
3.8.3 Color system................................................................................... 27
3.8.4 Dome reset ..................................................................................... 27
3.8.5 IR module setup ............................................................................. 27
Chapter 4 Short-Cut Operations and Specification of Dome Device....... 28
Chapter 5 Trouble Shooting of Dome Device ................................................ 31

Operation Manual of Intelligent Dome Camera
3
Chapter 1 Product Overview
1.1 Performance Instructions
1. The address of each Dome device is from 0 ～ 255. The number (address) of dome devices in the
control system is setup by the hardware (8-digit on and off switch) of the dome device.
2. Integrated multi-protocol and auto protocol differentiation. Note: The dome device only has auto
differentiate control of the first communication.
3. Pan 360 degree continuous scanning.
4. Tilt 90 degree action plus 2 degree angle adjustment. Plus the 2 degree adjustment, the view
angle can be 90 or 92 degree.
5. Pan manual operation speed can be 0.1 to 150 degree per second.
6. Tilt manual operation speed can be 0.1 to 55 degree per second.
7. 128 pre-shot positions (A fixed position that can be aimed by the dome camera, which can be set
and revised by user arbitrarily)
8. The maximum running speed when pre-shot is being utilized can reach 240 degree per second
with accuracy of ±0.1 degree.
9. Compatible with many camera modules (Sony, Hitachi, Sanyo, Yoke, CNB, LG, Haitron, Samsung,
DaHua)
10. Power supply: AC 24V1A (indoor type), AC 24V2A (outdoor type).
11. Easy installation interface.
12. Pass environmental protection grade IP66 (outdoor type).
13. Adopts long distance RS-485 transmission mode.
14. Transmission speed, i.e. Baud rate is selectable. (Set by the sixth and seventh bit of the on and
off switch of the dome device.2400bps~19200bps)
1.2 Feature Functions Instruction
1. English operation menu and function display.

Operation Manual of Intelligent Dome Camera
4
2. Camera name and operation position and angle display. (The name of the camera can be
edited and the coordinate angle of the dome device can be displayed on the screen.)
3. Operation crosshair function. (By enabling this option, the target can be captured more
effectively with crosshair on the screen).
4. Three PTZ tours operation with 8 minutes record of each tour. (Can record real-time monitor
and the action of manual operation)
5. Six groups of programmable vector scans. (includes scan speed, dwell time, pre-shot and
interruption between tours)
6. Auto flip function with 10 degree move up.
7. 24 sectors of programmable sectional mask. (Can mask part of the sectors of camera, which
differs depending on different types of camera)
8. 8 sectors of programmable sectional display. (Can display the name and nature of concrete
position shooting by the camera)
9. Auto enter function running after self-test of the dome device and auto enter function running
when there is no transmission. (Dwell time can be set from 5 to 999 seconds)
10. Freeze video picture function. (frozen picture function)
11. Operation return function. (after executing operation return, the dome device will return to the
previous operation)
12. Operational manual scan function. (execute this function in manual pan operation, you can
adjust the manual pan operation)
13. Intelligent power off real time memory. (If power is cut off when a certain function is in
operation, the dome device will resume working where the power was cut off).
14. High efficient 3-dimension scan.
15. Camera zoom in speed limit function. (When it is zooming in, the speed
of the dome device will auto slow down).
16. Remote setting of dome address.
17. The world's most advanced high-power infrared lamp technology
a. Infrared light power conversion efficiency, heat small, long life, low power, less than 5 watts,

Operation Manual of Intelligent Dome Camera
5
subversion of the traditional infrared lighting quick decline fatal shortcoming
b. Use its power can be considered as a single point of light source characteristics, developed
a variable angle infrared light
With the perspective of the size of the change in one machine simultaneously follow the
changes to ensure the infrared light is neither wasted nor flashlight effect, to maximize the use
of infrared light, the subversion of the traditional large volume of long-range needs of the
practice of tens of watts

Operation Manual of Intelligent Dome Camera
6
Chapter 2 Basic Configuration
2.1 Integrated Connection of Multiple Domes
When system connection for multiple domes is performed, lightning arresters, video matrix, DVR
video recorder, alarm, and other additional devices can be embedded to satisfy user’s actual need
to realize system integration.
AC24V: Power supply of dome (power supply of 110V/60HZ or 220V/50HZ input converted to
24VAC output)
RS-485B US: The output of control signal (RS-485 signals) from the controller connected to the
corresponding input of the dome
Video: The video output signal of dome (1Vp-p75 ohm)
(The output signal can be directly connected to video device such as display terminals or video
matrix. Use caution when performing impedance matching)

Operation Manual of Intelligent Dome Camera
7
Wiring Diagram for multiple domes
2.2 Setting protocol and baud rate of dome device
Before installation and use, the unique address for each dome and the communication protocol
including transmission speed (baud rate) should be set to correspond with the chosen control
system. The dome must be power cycled after each change.
Setting Impedance matching protocol and
baud rate of dome device
On/Off dip switch
Impedance matching setting Protocol setting Baud rate setting
Displa
y
Display
Display
AC24V
POWER
AC24V
POWER
AC24V
POWER
CONTROLLER
CONEROLLER
/DVR/DVS.etc
DOME #2
DOME #N
DOME #1
RS485

Operation Manual of Intelligent Dome Camera
8
128
64
32
16
1
2
4
8
ON
1 2 3 4 5 6 7 8
2 4 16
ON
1 2 3 4 5 6 7 8
On/Off status
Protocol type
2
nd
digit
3
rd
digit
4
th
digit
5
th
digit
6
th
digit
7
th
digit
PELCO-D ON ON OFF OFF ** **
PELCO-P OFF OFF ON OFF ** **
Auto detect OFF OFF OFF OFF ** **
Attention: the unique address for each dome and the communication protocol including transmission
speed (baud rate) should be set to correspond with the control system. Please restart the dome after
each change.
2.3 Setting dome device address
Setting method: The sum of switch numbers when it is at ON position is the address of dome
device.
(2+4+16=22)The address is 22
Dome device range: 0 ～ 255
Matching numbers
RS485
Dome #N
This figure shows protocol of
PELCO-D, Baud rate of 2400.
status
Baud rate 6th digit 7th digit
OFF OFF
OFF
OFF
ON
ON ON
ON
2400
19200
9600
4800
On/Off

Operation Manual of Intelligent Dome Camera
9
Zoon in
Zoom out
Up
Down
Right
Left
Joystick
J
o
y
s
t
i
c
k
Rotate
2.4 Camera Installation
(Please refer to the section on Camera Installation for more details on this
operation)
Note: 1. Make sure the proper connection of flat flex ribbon that connects the camera module to the
dome device.
2. Different camera models may have different secured positions of the hole.
2.5 Startup the power supply of the dome device
Self-detecting of the dome device (rotating) and the camera (displaying dome info) starts with power
supply start up. Note: The dome device will commence with a tilt action for around 2-5 seconds
when starting self-detecting, then be blocked and make a “clicking” sound that is normal as the
dome is performing vertical positioning.
2.6 Controller Setting
Set the protocol, baud rate, and address of the keyboard controller to match the settings on the
dome. (For instructions of how to set the keyboard communication settings please refer to keyboard
controller manual).Attention: If the protocol setting of the dome is set to auto detection, the protocol
of keyboard controller can be set arbitrarily. But its baud rate should be set identically with that of the
dome device.
2.7 Start testing
When all of the above settings are completed you can start testing dome functionality.
1. Direction control test of dome device 2. Zooming control test of camera
The directions (up, down, left and
right) of the dome device can be
controlled by using the keyboard
controller, as indicated in the figure.
Note: the working of dome device
is normal
Zooming of the camera can be controlled
by zooming function Joystick or by using
TELE (zoom in) and WIDE (zoom out) on
the keyboard button.
Note: The camera and dome device are
normal
Zoom in

Operation Manual of Intelligent Dome Camera
10
2.8 Complete the test (Summary)
If you have achieved control of the dome device as described in section 2.7, the system is basically
normal. Do not change the wiring or the applied settings to prevent failure and loss.
If the dome does not respond to the command, or only partial functionality is achieved, verify the
wiring connections (section 2.1 and 2.4) and communication setting (section 2.2, 2.3 and 2.6)
carefully.

Operation Manual of Intelligent Dome Camera
11
Chapter 3 Menu setting
3.1 Operation instructions
Menu operation instruction: To make a selection, move the joystick in the Up or Down direction. The
on-screen arrow points to the selected option. Moving the joystick to the Left or Right position you
can change the value of your selection or enter the submenu for the selected option. Press the
button CLOSE on the keyboard controller to exit the menu or return to the previous menu (one layer
up)
Number setup.
1. Joystick Left or Right when programming to select preset.
2. Press OPEN to confirm, open and display the number selection cursor
3. Joystick Left or Right to select the number to be entered
4. Press OPEN to confirm selection. The selected number is displayed on the corresponding data
bit.
5. Input number of respective data bits as shown above.
6. Press CLOSE to exit or return to the previous menu level when programming is done.
3.2 Main menu
95+SHOT+ACK to enter the main menu of the dome as illustrated down
1. Language Setup
Language: English.
2. Dome Information
Joystick down to move the cursor to press
OPEN or joystick left or right to move the
joystick to enter the menu.
3. Display Options
Display dome info or function.
4. Control Options
Set the pan or tilt and camera of the dome
manually or auto compatible with the entire
control system. User individualized operation
setting.
IR-006
1 LANGUAGE ENGLISH
2 DOME INFORMATION
3 DISPLAY OPTIONS
4 CONTROL OPTIONS
5 CAMERA OPTIONS
6 FUNCTION PROGRAMMING
7 SYSTEM SETUP

Operation Manual of Intelligent Dome Camera
12
3.3 Dome information
Joystick down to move the cursor to press
OPEN or joystick left or right to move the
joystick to enter the menu
5.Camera Options
Set camera function.
6. Function Programming
Program and execute PTZ and Vector Scan
etc.
7. SYSTEM SETUP
System setup, Including, restore defaulter
setup clear memory, color system, dome reset
3.4 Display Options
Set the display of dome info or function
3.4.1 Camera Name Setup
Set the camera name
PLEASE ENTER:
WELCOME________
ABCDEFGHIJKLMN
OPQRSTUVWXYZ
0123456789_
IRIS OPEN WHEN DONE
IRIS CLOSE TO EXIT
DISPLAY OPTIONS
1 CAMERA NAME SETUP
2 COORDINATES ON
3 START_UP SCR MSG ON
4 CROSSHAIRS ON
Operation steps:
⒈ Joystick up/down to move the cursor to select Display
Options
⒉ Joystick left/right to enter Display Option
⒊ Joystick up/down to select either one of the sub-menu
⒋ Joystick left/right to select ON/OFF
IR-006
CAMERA : xxxx
PROTOCOL : xxxx
BAUDRATE : xxxx
DOME NO . : xxx
VERSION : xxx
IRIS CLOSE TO EXIT
CAMERA NAME SETUP
1 NAME ___________
2 NAME DISPLAY OFF
1.NAME
[1] Move the joystick up/down to move the
cursor to select the Name.
[2] Move the joystick left/right or press OPEN to
enter name editing menu.
[3] Move the joystick left/right to select
“A~Z/0~9”, press “OPEN” to confirm, press
“CLOSE” to change or exit.

Operation Manual of Intelligent Dome Camera
13
3.5 Control Options
Set Auto Flip 、 Auto Focus 、 Auto AE, etc Move the joystick left/right or press
OPEN to enter control options
3.5.1 Dome Addr Stetup
3.5.2 Control Option Operation
Move the cursor to select Auto Flip/Proportional Speed/Pan Reverse/ Tilt Reverse/Vector Scan
Still/Vector Scan AF/+2 Tilt Limit/Speed Limit.
Move the joystick left/right or press OPEN to Display on/off/PTZ/Z/OFF
1. Auto Flip: If the camera lens auto rotates pan 180°then tilt 10°to auto track forward when the lens
goes down tilt 90°.
2. Auto AE: If the camera is AE when the dome device changes its pan or tilt or zoom.
3. Vector Scan AF: If the camera AF when vector scan is running.
4. Speed Limit: the moving speed of dome device matching the video ratio to lower the speed.
6 VECTORSCAN STILL OFF
7 AUTO FOCUS
PTZ
8 AUTO AE PTZ
9 VECTORSCAN AF OFF
10 -2 TILT LIMIT OFF
11 SPEED LIMIT OFF
CONTROL OPTIONS
1 DOME ADDR STETUP
2 AUTO FLIP ON
3 PROPORTIONAL SPD ON
4 PAN REVERSE OFF
5 TILT REVERSE OFF
1. Joystick left/right to setup the addr type.
addr type through Physic/Logic.
2.Joystick left/right to
change the dome ID(only when
addr type selects logic).
3. Joystick left/right to setup the b
roadcast ID
ON/OFF.
DOME ADDR SETUP
1 ADDR TYPE PHYSIC
2 DOME ID 1
3 BROADCAST ID OFF

Operation Manual of Intelligent Dome Camera
14
3.6 Camera Options(example: sony camera)
Move the joystick left/right or press OPEN to enter Camera options.
3.6.1 Zoom and Focus
3.6.2 Camera Exposure
1.AE Mode
Steps:
⑴ .Move the joystick up/down to move
the cursor to select AE Mode.
2.Slow Speed(MANUAL/Slow MD)
Steps:
⑴ .Joystick up/down to move the cursor
to select SHUTTER MD.
CAMERA OPTIONS
1 ZOOM AND FOCUS
2 CAMERA EXPOSURE
3 OTHERS
ZOOM AND FOCUS
1 ZOOM SPEED 7
2 DIGITAL ZOOM ON
3 AF SENSITIVITY HIGH
1. Zoom Speed
Steps:
.Move the joystick up/down to select
ZOOM SPEED.
. Joystick left/right to setup the camera
ratio speed.
2. Digital Zoom
Steps:
.Move the joystick up/down to move the
cursor to select DIGITAL ZOOM.
.Joystick left/right to setup the camera
digital zoom ON or OFF.
ZOOM AND FOCUS
1 ZOOM SPEED 7
2 DIGITAL ZOOM ON
3 AF SENSITIVITY HIGH
3.AF Sensitivity
Steps:
1. Move the joystick up/down to move the
cursor to select AF Sensitivity.
2. Joystick left/right to setup AF Sensitivity
function of the camera
ZOOM AND FOCUS
1 ZOOM SPEED 7
2 DIGITAL ZOOM ON
3 AF SENSITIVITY HIGH

Operation Manual of Intelligent Dome Camera
15
⑵ .Joystick left/right to set up camera
in command of different switchover
(AUTO/MANUAL/IRIS etc.)
⑵ .Joystick left/right to set up Slow SPEED.
3. Shutter Speed (Shutter Speed works under
Manuel/Shutter MD)
Steps:
⑴ .Joystick up/down to move the cursor to
select Shutter MD
⑵ .Joystick left/right to set up Shutter Speed
4. Iris (IRIS works under Manual/IRIS MD)
Steps:
⑴ .Joystick Up/Down to move the cursor to
select IRIS
⑵ .Joystick Left/right to set up the size of IRIS
5. AGC Level(AGC Level works under Manual
MD)
Steps:
⑴ .Joystick Up/Down to move the cursor to
6. Bright level (It works under
AUTO/MANUALMD)
Steps:
⑴ .Joystick up/down to move the cursor to
CAMERA EXPOSURE
1 AE MODE AUTO
2 SLOW SHUTTER OFF
3 SHUTTER SPEED AUTO
4 IRIS LEVEL AUTO
5 AGC LEVEL AUTO
6 BRIGHT LEVEL AUTO
7 SPOT AE OFF
8 WDR OFF
CAMERA EXPOSURE
1 AE MODE AUTO
2 SLOW SHUTTER OFF
3 SHUTTER SPEED AUTO
4 IRIS LEVEL AUTO
5 AGC LEVEL AUTO
6 BRIGHT LEVEL AUTO
7 SPOT AE OFF
8 WDR OFF
CAMERA EXPOSURE
1 AE MODE AUTO
2 SLOW SHUTTER OFF
3 SHUTTER SPEED AUTO
4 IRIS LEVEL AUTO
5 AGC LEVEL AUTO
6 BRIGHT LEVEL AUTO
7 SPOT AE OFF
8 WDR OFF
CAMERA EXPOSURE
1 AE MODE AUTO
2 SLOW SHUTTER OFF
3 SHUTTER SPEED AUTO
4 IRIS LEVEL AUTO
5 AGC LEVEL AUTO
6 BRIGHT LEVEL AUTO
7 SPOT AE OFF
8 WDR OFF

Operation Manual of Intelligent Dome Camera
16
select AGC Level.
⑵ .Joystick Left/right to set up the value of AGC
Level.
select Bright level.
⑵ .Joystick left/right to set up Bright level.
7.Spot AE(OFF/ON)
Steps:
⑴ .Joystick Up/Down to move the cursor
to select Spot AE.
8.WDR(OFF/ON)
Needs support from camera ：
⑴ .Joystick up/down to move the cursor to
select WDR.
⑵ .Joystick Left/right to set up the ⑵ . Joystick left/right to set up the status pattern
Spot AE of WDR.
CAMERA EXPOSURE
1 AE MODE AUTO
2 SLOW SHUTTER OFF
3 SHUTTER SPEED AUTO
4 IRIS LEVEL AUTO
5 AGC LEVEL AUTO
6 BRIGHT LEVEL AUTO
7 SPOT AE OFF
8 WDR OFF
CAMERA EXPOSURE
1 AE MODE AUTO
2 SLOW SHUTTER OFF
3 SHUTTER SPEED AUTO
4 IRIS LEVEL AUTO
5 AGC LEVEL AUTO
6 BRIGHT LEVEL AUTO
7 SPOT AE OFF
8 WDR OFF
CAMERA EXPOSURE
1 AE MODE AUTO
2 SLOW SHUTTER OFF
3 SHUTTER SPEED AUTO
4 IRIS LEVEL AUTO
5 AGC LEVEL AUTO
6 BRIGHT LEVEL AUTO
7 SPOT AE OFF
8 WDR OFF
CAMERA EXPOSURE
1 AE MODE AUTO
2 SLOW SHUTTER OFF
3 SHUTTER SPEED AUTO
4 IRIS LEVEL AUTO
5 AGC LEVEL AUTO
6 BRIGHT LEVEL AUTO
7 SPOT AE OFF
8 WDR OFF

Operation Manual of Intelligent Dome Camera
17
3.6.3 Others
3.7 Function Programming
3.7.1 Preset.
1.Number
.Move the joystick left/right or press OPEN to enter the number editing programming.
PS: Program the number of preset position.
OTHERS
1 SHARPNESS 5
2 BACK LIGHT OFF
3 WB MODE AUTO
4 R GAIN AUTO
5 B GAIN AUTO
6 VERTICAL MIRROR OFF
7 HORIZONTAL MIRROR OFF
8 IR SW MODE AUTO
9 STABILIZATION OFF
10 FUNCTION OSD ON
FUNCTION PROGRAMMING
1 PRESET
2 VECTORSCAN
3 PATTERN
4 SECTOR SETUP
5 MASK ZONE
6 MASK COLOR
7 MOTION
Preset option:
1. Move the joystick left/right or press
OPEN to enter Function Programming options.
2. Move the joystick up/down to move the
cursor to select the preset options.
3. Move the joystick Left/Right or press
OPEN to enter preset options.
1. Move the joystick up/down to move the
cursor to select the options.
2. Move the joystick Left/Right to set up the
options.

Operation Manual of Intelligent Dome Camera
18
. Move the joystick left/right to select “0~9” press “OPEN” to confirm, press “CLOSE” to exit.
2.Set Preset.
.Move the cursor to select preset position.
.Move the joystick left/right or OPEN to enter the setting (ensure the preset position data you
desire to save)
.Press OPEN to finalize your selection, then the screen displays STORED and return to the
previous menu level. Or press CLOSE to return to the previous menu level. without save your
selection.
PRESET
1 NUMBER 1
2 SET PRESET
3 CALL PRESET
4 DELETE PRESET
5 NAME _____________
6 NAME DISPLAY OFF
PRESET
1 NUMBER 1
2 SET PRESET
3 CALL PRESET
4 DELETE PRESET
5 NAME _____________
6 NAME DISPLAY OFF
IRIS OPEN WHEN DONE
STORED
INPUT RANGE:
1~50 64~77 102~165
001
0123456789
IRIS CLOSE WHEN DONE