Richard Wolf E2085.00 Series User manual

EE (LOF)
MODEL E2085.00 SERIES
BIPOLAR ELECTROSURGICAL GENERATOR
OPERATION MANUAL
This instruction manual covers the functions
of units E2085.00B (black faceplate) and
E2085.00 (cream faceplate).

OLE 丹
MODEL
E2085.00
|
|
BIPOLAR
ELECTROSURGICAL
GENERATOR
TABLE OF CONTENTS PAGE
GENERAL DESCRIPTION
PRECAUTIONS
OPERATION
FUSE REPLACEMENT
WARRANTY AND CUSTOMER SERVICE
TROUBLESHOOTING
SPECIFICATIONS
OD
B
BNB
-+
GENERAL DESCRIPTION
The Richard Wolf Model E2085.00 is a
mini-bipolar electrosurgical unit. An am-
meter is incorporated into the E2085.00 to
provide the surgeon with a visual indica-
tion of the progress of the operation.
Richard Wolf, as manufacturer and seller of these units, will not accept any liability for direct or consequential
damage caused by incorrect use or operation of these units, especially if these instructions are not followed
or the unit Is subjected to incorrect care or service.
E64-07-87 1/5

PRECAUTIONS |
Always observe. the following precautions when operating the E2085.00 Electrosurgical Generator:
e Carefully unpack the unit and visibly check to see if any damage occured during shipment.
e This unit was fully tested at the factory before shipment. As a precaution, it is recommended that the unit
be tested prior to a surgical procedure.
NEVER operate this unit in the presence of flammable anesthetics.
NEVER remove the cover, because of electric shock hazard. Refer servicing to qualified personnel.
For continued protection against fire hazard, always repiace the blown fuse with the same type and rating.
Do not use this unit without proper electrical ground.
Do not block the ventilation vents.
OPERATION
This section provides a description of the features and modes of operation of the Model E2085.00 Bipolar Electro-
surgical Generator.
POWER
The Power Switch (1) supplies current to the electrosurgical unit E2085.00. This switch should be turned on
only when Bipolar current is required and only then after following the operating instructions.
OPERATING INSTRUCTIONS: BIPOLAR
WARNING
DO NOT MODIFY THE BIPOLAR CABLE IN ANY WAY. ANY MODIFICATIONS ARE DONE AT YOUR
OWN RISK AND WILL VOID ALL WARRANTIES ON THIS CABLE AND ANY WOLF INSTRUMENTS
USED WITH IT.
1. Make sure all cables are in good condition.
2. Make sure ail connections are completely free of moisture.
3. Connect footswitch cable to Footswitch Receptacle (2). Place footswitch in proper position for operation (by
surgeon only.)
4. Insert active Bipolar cable into the Bipolar Receptacle (3). Do not connect active cable to instruments until
unit is ready to be used.
5. Depress the Power Switch (1).
6. Depress the footswitch when power is needed.
7. The Ammeter (5) provides the surgeon with a visual indication of the progress of his operation. Normal meter
operation would show a decrease in current flow as the tubal ligation progresses.
8. The tone emitted by the unit and the illumination of the Bipolar Indicator Light (6), above the Bipolar Recep-
tacle, indicates that the unit is functioning.
215 E64-07-87

OPERATION
FIGURE 1. Model 2085.00 Bipolar Electrosurgical Generator
FRONT
BACK
1. POWER SWITCH 6. BIPOLAR INDICATOR LIGHT
2. FOOTSWITCH RECEPTACLE 7. BUMPER TRIM
3. BIPOLAR RECEPTACLE 8. LINE CORD
4. BIPOLAR CURRENT CONTROL 9. FUSE—3 A/250 V
5. AMMETER 10. HANDLE
E64-07-87 3/5

FUSE REPLACEMENT |
To replace the fuse, push the Fuseholder Cap (9) in and to the left. Replace a blown fuse with the same type of
3 A/250 V (9) fuse. Push Fuseholder Cap (9) in and turn to the right.
If trouble is encountered with the Model E2085.00, perform the procedures in the Troubleshooting Chart. If the problem
persists, refer the unit to qualified personne! for servicing. For technical assistance, contact the Richard Wolf Customer
Service Department.
WARRANTY AND CUSTOMER SERVICE.
We unconditionally guarantee our instruments to be free from any defects in materials and workmanship under
normal use and service. If repair becomes necessary, our policy is one of customer accommodation.
These instructions do not attempt to cover all details or variations in equipment, nor to provide for every
possible contingency to be met in connection with installation, operation, or maintenance. Should further
information be required or should problems arise which are not covered sufficiently for the purchaser's purpose,
the matter should be referred to the Richard Wolf Medical Instruments Corp.
Our national sales and service offices, as well as our manufacturing facility, are located in Illinois.
Trained manufacturer’s representatives are located throughout the United States to serve you. For any ques-
tions regarding these instruments, or to place an order, contact the Richard Wolf Customer Service Department
at the following numbers: In Illinois, [phone];
Outside of Illinois, (800) 323-WOLF.
Instrument Ordering Policy
We reserve the right to make substitutions, if necessary, without prior notice.
Repair Policy
Defective merchandise will be repaired or replaced at no charge to the customer, provided the customer delivers
such defective merchandise prepaid.
Any repairs, maintenance or servicing of our merchandise by anyone other than a factory authorized represen-
tative will render our warranty null and void.
When returning your instrument for repair, we suggest that you use the box it was originally shipped in, in
order to prevent damage to the instrument in transit. We also recommend that the instrument be insured for an
amount to cover the cost of replacement.
IMPORTANT
FOR GENERAL SAFETY AND HEALTH REASONS, WE REQUIRE THAT YOU CLEAN AND STERILIZE ALL
INSTRUMENTS BEFORE RETURNING THEM FOR REPAIR. EFFECTIVE OCTOBER 1, 1990, IF INSTRUMENTS
ARE RECEIVED IN AN UNSANITARY CONDITION, THEY WILL BE RETURNED IMMEDIATELY TO THEIR
POINT OF ORIGIN, PREPAID.
TROUBLESHOOTING.
PROBLEM POSSIBLE SOLUTION
No
Bipolar
Output
Verify
that
the
unit
is
connected
to
the
AC
power
supply.
No Indicator Light or Audible Tone Inspect line cord for visible damage.
Check for blown 3A fuse.
Check that footswitch plug is properly inserted
and secured.
No Bipolar Output Check to ensure cables, plugs and insulation are in
Indicator Lamp Lights and Tone good condition. | |
Sounds but No Power Output Check that cable between bipolar forceps and bipolar
receptacle is properly inserted and secured.
Check that instrument tips are free of encrusted tissue.
Check that an adequate power setting is selected.
415 E64-07-87

SPECIFICATIONS
PHYSICAL
Height............... 5.0 in.
Width............... 12.5 in.
Depth .............. 12.0 in
Weight .............. 16 Ibs
ELECTRICAL .
Power Supply
Inside Fuse
Outside Fuse
Cord Plug
Line Cord
Bipolar Output
Maximum Power
120 V AC. 60 Hz
2.5 A/250 V SLO-BLO
3 A/250 V
Hospital Grade Hubbell
SJT 18/3-8ft. long
50 Watts
200 Watts
RICHARD WOLF MEDICAL INSTRUMENTS CORP.
353 CORPORATE WOODS PARKWAY « VERNON HILLS, IL 60061
Tel: [phone] + Customer Service: 1 (800) 323- WOLF
Repair Service:1 [phone]
E64-07-87 515