Richelieu SMART BTRF User manual

NOVEMBER 2022
RICHELIEU
SMART BTRF
INSTALLATION GUIDE

www.richelieu.com
PRODUCT DETAILS
■Smart LED Receiver BTRF24961248 ■Kinetic Smart
Switch RFDE2801Z
■2-zone Kinetic Smart
Switch RFDE2802Z
■Battery Powered Smart
Switch RFD9001Z
INSTALLATION GUIDE
NOTE: The LED receiver must always be used with a suitable 24V or 12V LED driver. Warranty does
not cover damage caused by the use of a driver not recommended by Richelieu Installation
must allow for the re-installation and repair of the receiver and switch without the removal
of fixed furniture. Installation must comply with your local, regional or national electrical
regulations.

www.richelieu.com
INSTALLATION GUIDE
NOTE: Do not press the connect button and switch simultaneously.
STEP BY STEP
Pairing the switch with the receiver:
After connecting all lamps to the receiver and then the receiver to the driver,you are now ready to pair
the switch with the LED receiver. Below,you will find the key things you need to know to succesfully pair
the devices.
STEP 1
If needed, remove the plastic from the battery inside the switch.
STEP 2
With RFDE2801Z, and RFD9001Z, all connected LED receivers are controlled simultaneously.
With RFDE2802Z the 2 zones in the switch correspond to their own LED receiver.
RECEIVER FACTORY RESET: To reset the receiver to its factory setting, press
the connect button (as shown on page 3) for 10 to 15 seconds. You will know the receiver is reset
when all connected lamps blink twice and stay on. If the connect button is not accessible,
reset the power of the receiver 8 times continuously.
STEP 3
Before using the switch, you must pair it with the receiver.
3.1 Keep the switch close to the receiver.
3.2 Short-press the connect button once and within 5 seconds, short-press any button on the switch.
You will know the devices are paired when all the lights connected to the receiver blink once.
If the connect button is not accessible, reset the power of the receiver 3 times continuously.
3.3 You now have successfully paired the switch with the receiver. If you are using the 2-zone switch,
please follow again steps 3.1 to 3.4 to pair the second zone to the other receiver. If the switch/receiver
does not work properly, repeat steps 3.1 to 3.3.
STEP 4
If you have several receivers to be connected with a switch, please repeat steps 3.1 to 3.3.
If you have several switches to be connected with a receiver, repeat steps 3.2 to 3.3.
Do not repeat step 3.1 if you don't want to lose the established connections with the switches.
STEP 5
If you want to change the settings or if the switch doesn't work properly, you must reset the receiver back
to factory settings and follow steps3.1to 3.3 to pair with the switch.

www.richelieu.com
NO BATTERY,
KINETIC POWER
1-ZONE WIRELESS
CONTROL
■Short press On-button turns on light,
long press brightens light
■Short press Off-button turns off light,
long press dims light
RICHELIEU SMART BTRF
INSTALLATION GUIDE
ON/ UP
OFF/ DOWN

www.richelieu.com
NO BATTERY,
KINETIC POWER
2-ZONE WIRELESS
CONTROL
■Short press On-button turns on light,
long press brightens light
■Short press Off-button turns off light,
long press dims light
RICHELIEU SMART BTRF
INSTALLATION GUIDE
ON/ UP
OFF/ DOWN

www.richelieu.com
RICHELIEU SMART BTRF
INSTALLATION GUIDE
UP
SCENE
DOWN
ON
OFF
BATTERY POWERED
SMART SWITCH
■Short press On-button turns on light
■Short press Off-button turns off light
■Long press Up-button brightens light
■Long press Down-button dims light
■Long press Scene-button saves a scene,
short press recalls the saved scene

www.richelieu.com
INSTALLATION GUIDE
■Max 10 pcs of light/LED receiver.
■One LED receiver can be controlled by max 8 switches.
■Maximum wattage of the receiver depends on the chosen driver.
■In any case, it cannot exceed 3Ax12V=36W or 3Ax24V=72W.
■Max 20 receivers can be controlled with one switch.
RICHELIEU SMART BTRF

CANADA Tel.: [phone] Fax: [phone]
UNITED STATES Tel.: [phone] Fax: [phone]
■12V Micro12 connector hub
■The maximum wattage of a 12V hub is 3A x 12V = 36W
SMART WIRELESS CONTROLLER
CHANGE OF BATTERY
INSTALLATION GUIDE
Richelieu Smart
BTRF

 

 ,;<(! : :

Richelieu

M 

g    
 
M 

g  
� Richelieu Richelieu Sma
� richelieu.com INSTALLATION SHEET GE4
Richelieu Smart
BTRF

 

 ,;<(! : :

Richelieu

M 

g    
 
M 

g  
� Richelieu Richelieu Sma
� richelieu.com INSTALLATION SHEET GE4
Richelieu Smart
BTRF

 

 ,;<(! : :

Richelieu

M 

g    
 
M 

g  
� Richelieu Richelieu Sma
� richelieu.com INSTALLATION SHEET GE4
■24V Micro24 connector hub
■The maximum wattage of a 24V hub is 3A x 24V = 72W
■Power Supply: 3VDC or Kinetic Power
■Frequency: 2.4GHz
■Battery: CR2430 or None
■Transmission Range: Up to 30 m in open air Richelieu recommends
that the switch and receivers be within a radius of 10 to 15 m
(32 to 49'). The switches and receivers have been tested in an open
environment with a maximum connectivity of 30 m (98').