Richen EF456B User manual

MODEL: EF456B/EF457B/EF458B/EF459B
Email: [e-mail]
R
CUS

1
This heater is hot when in use. To avoid burns, do not let bare skin
touch hot surfaces. If provided, use handles when moving this
heater. Keep combustible materials, such as furniture, pillows,
bedding, papers, clothes, and curtains at least a 3 feet (a 0.9m)
from the front of the heater and keep them away from the sides
and rear.
Extreme caution is necessary when any heater is used by or near
children or invalids and whenever the heater is left operating and
unattended.
Always unplug heater when not in use.
Do not use outdoors
This heater is not intended for use in bathrooms, laundry areas and
similar indoor locations. Never locate heater where it may fall into
a bathtub or other water container.
Do not insert or allow foreign objects to enter any ventilation or
exhaust opening as this may cause an electric shock or fire, or
damage the heater.
To disconnect heater, turn controls to off, then remove plug from
outlet.
Connect to properly grounded outlets only.
Do not operate any heater with a damaged cord or plug or after
the heater malfunctions, has been dropped or damaged in any
manner. Discard heater, or return to authorized service facility for
examination and/or repair..
Do not run cord under carpeting. Do not cover cord with throw
rugs, runners, or similar coverings. Do not route cord under
furniture or appliances. Arrange cord away from traffic area and
where it will not be tripped over.
To prevent a possible fire, do not block air intakes or exhaust in any
manner. Do not use on soft surfaces, like a bed, where openings
may become blocked.

This heater may include an audible (a visual) alarm to warn that
parts of the heater are getting excessively hot. If the alarm sounds
(flashes), immediately turn the heater off and inspect for any
objects on or adjacent to the heater that may cause high
temperatures. DO NOT OPERATE THE HEATER WITH THE ALARM
SOUNDING (FLASHING).
Always plug heaters directly into a wall outlet/receptacle. Never
use with an extension cord or relocatable power tap (outlet/power
strip).
Use this heater only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock,
or injury to persons.
A heater has hot and arcing or sparking parts inside. Do not use it
in areas where gasoline, paint, or flammable liquids are used or
stored.
Hyperthermia can result in death. Symptoms of hyperthermia
include high body temperature, headache, nausea, vomiting,
tiredness, dizziness, fainting, and rapid pulse. If you begin to
experience symptoms related to hyperthermia, turn off the heater
and seek medical attention.
To avoid excessive room temperatures which can cause
hyperthermia: DO NOT leave product running unattended in a
confined space around infants, or individuals with reduced physical,
sensory, or mental capabilities.

MODEL NO.: EF456B/EF457B/EF458B/EF459B
Supply Voltage: AC120V/60Hz
Maximum power consumption: 1.5KW
Power for flame and fuel bed effect: 7W/7W/9.5W/9.5W
Standing Bracket L Bracket
8/8/8/10x 8/8/8/10x
Screw ST4*10

A
B
6 ⁄"
12 ⁄"
C
⁄"
12 ⁄"
4 ⁄"
Crystal Media
Email: [email protected]om

A screwdriver and a Φ8mm impact drill will be needed.
WARNING! Risk of Fire! Keep electric cords, drapery, furnishings or
other combustibles at least 3ft. (0.9m) from the front of the electric
fireplace.

NOTE: Save all the parts removed from the appliance.
Remove 4 screws on both sides of the trim and remove the trim,
then remove the front glass by removing 4 screws and 2 fixers.
REMOVE FRONT TRIM AND GLASS
Installing the Appliance
REMOVE WALL MOUNTING BRACKET

CHOOSE A WAY TO INSTALL
IN WALL RECESSED
Build a frame with power supply as shown below.
Model
A
EF456B EF457B EF458B EF459B
34 ⁄" 38 ⁄" 58 ⁄" 48 ⁄"
A
12 ⁄"
min. 3 ⁄"
Finish the wall by paint or wall paper.

Insert the unit into the wall and fix it by 4pcs ST4*40 screws.
Evenly scatter the crystal media on fuel bed.
Carefully fix the glass and trim back, the installation is completed
now.

Insert wall plug (for concrete wall only) into the holes and secure
the bracket to the wall with ST5*40 screws.
Fix the L brackets to the bottom of the firebox with four ST4*10
screws.
IN WALL RECESSED
Locate the wall mount bracket and mark the position of the holes.
Wall
Bracket
Floor
12
34
56

Hang the firebox on the wall bracket and mark the position of the L
bracket, then take the firebox down. Drill 2 holes on the marked
point, insert 2 wall plugs into the holes, then hang on the firebox
again and fix it by two ST5*40 screws.
Repeat the steps mentioned above to arrange the fuel bed and fix
the front glass and trim back.

FREE STANDING
Install the standing bracket on the bottom of the appliance with
four ST4*10 screws.
Repeat the steps mentioned above to arrange the fuel bed and fix
the front glass and trim back.
BEFORE OPERATION

OPERATION METHOD
STAND BY
TEMPERATURE
HEATERFLAME
7 DAYS
TIMER INDICATOR
DISPLAY
HEATING
INDICATOR
1. STANDBY: Turns on the appliance with the last used settings including
heater. Place the appliance into standby mode with all features turned
off.
2. FLAME: Press to cycle through 9 flame colours and off setting.
3. HEATER: Press to cycle through low heater, high heater and off setting.
4. TEMPERATURE: Press to adjust the heaters response to the ambient
temperature conditions in the room. Temperature adjusts from 16 °C -
28 °C (60 °F - 84 °F) and then 58°C (99°F).
MANUAL CONTROL

STAND BY
BRIGHTNESS
TEMPERATURE
TIMER
FLAME
HEATER
7 DAYS TIMER
TIME
ENTER
REMOTE CONTROL

Press button STAND BY on the appliance to turn it off and leave
it off for approximately 10-15 minutes.
1. Two AAA alkaline batteries are required for the remote control;
2. Two Use the thumb press and push the bar figure on the back cover
down simultaneously, then take out the cover and remove the
battery or insert the battery, after this place the cover back on the
rear of the remote;
3. This AAA battery (non-recharged) is not to be recharged;
4. Different types of batteries or new and used batteries are not to be
mixed;
5. Battery is to be inserted with the correct polarity;
6. Exhausted batteries are to be removed from the appliance and safely
disposed of;
7. If the remote control is to be stored unused for a long period, the
battery should be removed;
8. The supply terminals are not to be short-circuited.