Richen MT119A User manual

Assembly, Installation and
Users Instructions
Model: MT119A Fireplace Mantel
For use with EF119B - 2kW Electric Fire
PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING APPLIANCE.
INSTALLER: DO NOT DISCARD THIS MANUAL –LEAVE WITH THE CUSTOMER
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
TABLE OF CONTENTS

2
SECTION 1: SAFETY TIPS..........................................................................................................................................3
SECTION 2: DIMENSIONS……...................................................................................................................................3
SECTION 3: INSTALLATIONS
3.1 Parts of mantel & content list..................................................................................................................................4
3.2 Before Installation…………………….. ...................................................................................................................5
3.3 Installation……………………………………… ....................................................................................................5, 6
SECTION 4: CLEANING & MAINTAINENCE...............................................................................................................7
1. Before assembly(remove), CAREFULLY use scissors or utility knife to cut and unwrap all parts. MAKE
CAUTION: BEFORE OPERATING PLEASE READ THESE INSTRUCTIONS
CAREFULLY.
SECTION 1 SAFETY TIPS

3
SURE YOU DO NOT DISCARD THE PACKAGING.
2. Make sure that you have all the parts listed below before assembling(remove).
3. Some steps are more easily handled with two adults.
4. Complete the assembly the Fireplace Mantel before fitting the Electric Fire. INSTALL THE ELECTRIC FIRE
E114R Referring to the separate instructions supplied. IMPORTANT NOTE –ONLY FIT THE FIRE FROM
THE BACK OF THE FIREPLACE SO AS NOT TO SCRATCH THE BASE(change to ‘MANTEL’).
5. Take care when assembling your new fireplace(remove). Only use the fixing supplied (add ‘to assembly the
mantel’).
6. DO NOT OVERTIGHTEN BOLTS.
7. Save these instructions for future reference.
Warning - This fireplace suite must be fitted to the wall. Mirror plates are supplied with the electric fire but any
other suitable concealed fixing may be used.
Dimensions in mm
Model
Width
（W）
Height
（H）
Depth
（D）
Mantel opening size
Width（OW）
Height（OH）
MT119A
1000
825
275
604
437
SECTION 2 DIMENSIONS
SECTION 3 ASSEMBLY AND INSTALLATION

4
3.1 Unpack
Open the package carefully and remove all pieces. Carefully inspect each part for any damage before you
begin assembly. (add: If there is any damage on the part, please feel free to contact with us at tel: …..)
3.1.1 Parts of mantel & contents list (remove):
A
B
C
D
E
F
G
H
Note: left and right of product are distinguished by its front view.
No.
Name
Q’ty
A
Top panel
1
B
Front top panel
1
C
Left side panel
1
D
Right side panel
1
E
Opening top panel
1
F
Opening bottom panel
1
G
Base panel
1
H
Fire support panel
1
I
Wood dowel
8+1(Spare)
J
Screws M6*30mm
19+1(Spare)
K
Washer
19+1(Spare)
3.2 Before installation:
a. Tools required: Magnetic Phillips screwdriver 1pc

5
Hammer 1pc
b. Position of fixing show below:
3.3 Installation:
NOTE!
Use manual screwdriver Only;
Use washer when fixing with screws;
Knock in with a hammer the 8 dowels in the left(C) and right(D) side panels where shown prior to assembly.
Do not use screws of other types or models, in case that the screws are too long, causing damage to
mantels.
Assembly required by two adults.
C
D
G
F
E
Step1.Fix side panels (C&D) onto base panel (G).
Step 2. Fix opening top panel (E) and bottom panel
(F).

6
socket of mood lighting
F
E
B
Step 3. Pass the socket and wire of mood lighting
through the hole on the right side panel (D) before
fixing of front top panel (B); Check that the led strip is
still pushed firmly down into position on the self-
adhesive pads
Step 4. Fix the opening top panel (E) with front top
panel (B);
Fix the opening bottom panel (F) ;
H
A
Step 5. Fix top panel (A) and fire support panel (H);
Step 6. Install the fire from back of the mantel, and
use 4 screws to fix firmly. (Screws are supplied
together with the fire).
Connect the plug and socket of mantel mood lighting.
(Detailed in the fire instructions E114R)
SECTION 4 CLEANING & MAINTAINENCE

7
1 Your fireplace mantel surface coating will give off a slight smell for a short period of time. Try to ventilate as
much as possible during this time.
2 Daily cleaning: Clean the mantel surfaces with a soft, lint-free cloth. Do not use cleaning or polishing
products and try to avoid heavy or sharp articles which may damage the surface.
3 Avoid long-term direct sunlight, and excessive temperatures and humidity to protect the life of your furniture
(change to ‘mantel’)surface.