Richmat HJC26C Ble User manual

Control box
HJC26C Ble

1.Remark:
Up to 2 motors
BLE control available
Memory function
Color: black
2.Dimension:

3.System configuration diagram
4.Remote control button silicone diagram

5.Remote control function description
Button
label
function
1
ANTISORE (anti-screaming): Tap to run to the leisure
position (there is an initial position). The customer
cannot modify the location.
2
ZG (Zero Gravity): Tap to run to zero gravity position.
(With initial position) Multiplexing function: FLAT+ZG
for about 3s, the backlight of the remote control flashes,
the buzzer of the control box sounds "dididi", and the
current position is memorized as the ZG (zero gravity)
position. The power is not cleared. Restore factory
settings: FLAT+ back legs rise simultaneously for about
3s, the backlight of the remote control flashes, the
buzzer of the control box sounds "di di di di", and the
memory of the previous motor position is cleared.
3
LOUNGE (leisure): Tap to run to the leisure position.
(With initial position) Multiplexing function:
FLAT+LOUNGE for about 3s, the backlight of the remote
control flashes, the buzzer of the control box sounds "di
di di di", and the current position is memorized as LOUNGE
(leisure) position. The power is not cleared. Restore
factory settings: FLAT+ back legs rise simultaneously for
about 3s, the backlight of the remote control flashes,
the buzzer of the control box sounds "di di di di", and
the memory of the previous motor position is cleared.
4
M1 memory position: click to run to M1 position. (No
initial value) Multiplexing function: FLAT+M1 for about
3s, the backlight of the remote control flashes, the
buzzer of the control box sounds "dididi", and the current
position is memorized as the memory position of M1. The
power is not cleared. Restore factory settings: FLAT+
back legs rise simultaneously for about 3s, the backlight
of the remote control flashes, the buzzer of the control
box sounds "di di di di", and the memory of the previous
motor position is cleared.
5
The back and legs rise at the same time: Press the button,
the back motor and the leg motor extend at the same time,
release to stop.
6
Back and legs down: press the button, the back motor and
the leg motor retract at the same time, release it to stop.
7
Press the button, the back motor extends, release it to
stop.
8
Press the button, the leg motor extends, release it to
stop.
9
Press the button, the back motor retracts, release it to
stop.

10
Press the button, the leg motor retracts, release it to
stop.
11
One-button reset: press the button, the massager is
turned off, and the motor retracts to the FLAT position
at the same time. (Not reset after power on)
12
Short press the button: If the back massage motor is not
activated, it will start the back massage motor and enter
the first-level intensity "CONSTANT" mode. If the back
massage motor is activated, the vibration intensity of
the back massage motor will be increased, a total of eight
intensities, if it is at the highest level Position, press
the button again to turn off the massager. The default
time is 15 minutes. Long press the button: every 1S, the
intensity will increase by 1 level.
13
Short press the button: If the leg massage motor is not
activated, start the leg massage motor and enter the
first-level intensity "CONSTANT" mode. If the leg massage
motor is activated, the vibration intensity of the leg
massage motor will be increased, a total of eight
intensities. If in the highest gear, press the button
again to turn off the massager. The default time is 15
minutes. Long press the button: every 1S, the intensity
will increase by 1 level.
14
The WAVE mode is: WAVE 1-WAVE 2-WAVE 3-WAVE 4-FULL BODY
1-FULL BODY 2-STOP cycle in turn; the initial intensity
of WAVE is: 1 level; (default 15 min)
15
The massager is turned off. The massager timing button
is to set the working time of the massage motor to 10min,
20min, and 30min respectively, and cancel the timing
(that is, restore the default time of 15min). The timing
time is displayed by three indicator lights. The maximum
timing time is 30min. If the massager is not working, it
will directly time the next massage motor working time.
If the working time is not set, the control box will be
powered off and re-energized. The initial default time
is 15min.
16
Light switch under the bed. (Default 15min)
17
Press the button, the flashlight turns on; release the
button, the flashlight turns off.
Coding method:
Keep pressing the head-down and foot-down buttons (9, 10) until the
backlight flashes to clear the remote control code
matching information, and power on the control box again.
The control box will be in the code matching state within
20s. Keep pressing the head up and down buttons of the
remote control The backlight of the head down buttons (7,
9) flashes, and the buzzer sounds, indicating that the
code matching is completed.

Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.