Ricoh EV-G030B1 User manual

1
EV-G030B1 / EV-G200C1 / EV-G200B1
Specifications Rev. 1.00
GigE Vision
Extended-Depth-of-Field Camera
EV-G030B1 (VGA, Monochrome)
EV-G200C1 / EV-G200B1 (UXGA, Color /Monochrome)
Product Specifications
RICOH COMPANY, LTD.

2
EV-G030B1 / EV-G200C1 / EV-G200B1
Specifications Rev. 1.00
!
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
Warning:
This equipment generates and uses radio frequency energy and if
not installed and used properly, I.e., in strict accordance with the
instruction manual, may cause harmful interference to radio
communications. It has been tested and found to comply with the
limits for a Class A computing device pursuant to Subpart J of Part
15 of FCC Rules, which are designed to provide reasonable
protection against such interferencewhen operated in a commercial
environment.
For U.S.A.
Warning:
This digital apparatusdoes not exceed the Class A limits for radio
noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of
Communications.
For Canada
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THISAPPLIANCE TO RAIN OR MOISTURE.
Safety Precautions
Product Precautions
Handle the camera with care. Do not abuse the camera. Avoid striking or shaking it. Improper handling or
storage could damage the camera.
Do not pull or damage the camera cable.
During camera use, do not wrap he unit in any material. This will cause the internal temperature of the unit
to increase.
Do not expose the camera to moisture, or do not try to operate it in wet areas.
Do not operate the camera beyond its temperature, humidity and power source ratings.
While the camera is not being used, keep the lens or lens cap on the camera to prevent dust or
contamination from getting in the CCD or filter area and scratching or damaging this area.
Do not keep the camera under the following conditions:
In wet, moist, and high humidity areas
Under hot direct sunlight
In high temperature areas
Near an object that releases a strong magnetic or electric field
Areas with strong vibrations
Use a soft cloth to clean the camera. Use pressured air spray to clean the surface of the glass. DO not
scratch the surface of the glass.

3
EV-G030B1 / EV-G200C1 / EV-G200B1
Specifications Rev. 1.00
Index
1SPECIFICATIONS....................................................................................................4
1.1 Electronic specifications / Mechanical specifications / Environmental specifications
EV-G030B1......................................................................................................................................... 4
1.1.1 Spectral Sensitivity Characteristics...................................................................................................5
EV-G030B1.................................................................................................................................................................... 5
1.2 Electronic specifications / Mechanical specifications / Environmental specifications
EV-G200C1/EV-G200B1..................................................................................................................... 6
1.2.1 Spectral Sensitivity Characteristics...................................................................................................7
EV-G200B1.................................................................................................................................................................... 7
EV-G200C1 (with IR cut filter) .................................................................................................................................... 7
1.3 Operational temperature and the power consumption......................................................... 8
2CONNECTOR SPECIFICATIONS............................................................................9
2.1 RJ45 connector ........................................................................................................................ 9
2.2 LED information ..................................................................................................................... 10
2.3 Power/IO connector ............................................................................................................... 11
2.3.1 Input signal.........................................................................................................................................12
2.3.2 Output signals....................................................................................................................................12
2.4 DC IRIS lens connector.......................................................................................................... 13
3I/O CIRCUITS.........................................................................................................14
3.1 Input circuit............................................................................................................................. 14
3.1.1 Example circuit for the input signal.................................................................................................15
3.2 Output circuit.......................................................................................................................... 16
4DIMENSIONS.........................................................................................................17

4
EV-G030B1 / EV-G200C1 / EV-G200B1
Specifications Rev. 1.00
1 Specifications
1.1 Electronic specifications / Mechanical specifications / Environmental specifications EV-G030B1
Noise level at 8bit outpu
t
at 10bit outpu
t
at 12bit outpu
t
Minimum scene illumination
Protocol
ALC
AOI function
Smear reduction
Color interpolation
Input voltage
Consum
p
tion
Material
Lower limit
Higher limi
t
No filter
EV-G030B1
1/3" interline VGA monochrome
progressive CCD: ICX424AL
0.58 Lux at F1.2, 89.91172Hz
Digital 8, 10 or 12 bit Raw data
Gamma 1.0 (Factory default) or downloadable gamma table
Programmable AOI setting via the communication
Selectable ON/OFF via communication
Standard compliancy EMS: EN61000-6-2, EMI: EN55011 Group 1 Class A
RoHS RoHS compliant
Environmental
specifications Operational
temperature Environmental temperature -5 deg. C
Camera housing temperature (Top plate): 70 deg. C (Check "Operational temperature and power consumption")
Storage temperature Environmental temperature -30 to 65 deg. C
Vibration 20Hz to 200Hz to 20Hz (5min./cycle), acceleration 10G, 3 directions 30 min. each
Shock Acceleration 38G, half amplitude 6ms, 3 directions 3times each
Power/IO connector: HR10A-10R-12PB (Hirose) or equivalent
DC IRIS lens connector: M1951 (EMUDEN) or equivalen
t
Camera mount screws Two 1/4" Tri
p
od screw holes
(
one each on to
p
and bottom
p
late
)
Sixteen M4 screw holes
(
four each on to
p
, bottom and both sides
p
late
)
Weigh
t
A
pp
roximatel
y
170
g
Positional accuracy in H and V directions: +/- 0.3 mm
Rotational accuracy of Ha nd V: +/- 1.5 deg.
Aluminum
(
AC
)
Lens mount C mount
Connectors RJ45 connecor
Auto IRIS lens control Not available
Power +10.8 to +26.4Vdc through power/IO connector orPower Over Ethernet
(Auto detection with power/IO connector prioritized)
Mechanical
specifications Dimensions 50 (W)x 50 (H) x 53.5 (D) mm excluding connectors
Optical filter
Optical center accuracy
Not available
Not available
I/O's UART communication through Ethernet port
White Balance function
Three opt isolated inputs and five opt isolated outputs
Communication Ed
g
e
p
reset tri
gg
er,
p
ulse width tri
gg
er
(
unlimited lon
g
ex
p
osure
)
Exposure time Preset continuous mode: 10 usecondsto 16,777,216 useconds
Preset trigger mode: 10 useconds to 16,777,216 useconds
Pulse width mode: 10 useconds to Unlimited
AGC (ON/OFF)
Gain 0 to 20.4 dB
<= 48 Digit (Gain 0 dB)
Internal
Video output
Interface PoE : IEEE802.3af CLASS3 (1000BASE-T)
GigE Vision 1.2 and GeniCam 2.0 compilant
Maximum frame rate of the camera (360.33325 Hz) is 104 vertical resolution AOI setting
Horizontal frequency 47.2028 kHz
36.818175 MHz
<= 3 Digit (Gain 0 dB)
<= 12 Digit (Gain 0 dB)
Scanning system Progressive
Vertical frequency (Frame rate) 89.91172 Hz at full resolution
0.72028 to 360.33325 Hz changeable via the communication
Maximum frame rate is depending on the AOI setting
692 (H) x 504 (V)
Active picture elements
VGA: 648 (H) x 494 (V
)
*EV-G003B1: With respect to the entered size, the 15 pixels above and below, and the 0 to 14th
pixels and 633rd to 647th pixelson the left and right sides will be blacked out.
Chip size 5.79 (H) x 4.89 (V) mm
7.4 (H) x 7.4 (V) µm
Product
Electronic
specifications Ima
g
er
Total picture elements
Cellsize
Pixel frequency
Sync. System
Gamma
Tri
gg
er mode
Less than 6.5 W
/
FCC 47CFR Part 15 Subpart B Class A
（
Verification
）
/ ICES-003
（
Cla ss A
）

5
EV-G030B1 / EV-G200C1 / EV-G200B1
Specifications Rev. 1.00
1.1.1 Spectral Sensitivity Characteristics
EV-G030B1
1
0.8
0.4
0.6
0.2
0400 500 600 700 800 900 1000
Relative Response
Wave length [nm]

6
EV-G030B1 / EV-G200C1 / EV-G200B1
Specifications Rev. 1.00
1.2 Electronic specifications / Mechanical specifications / Environmental specifications
EV-G200C1/EV-G200B1
Product EV-G200C1 EV-G200B1
Imager 1/1.8" interline UXGA color 1/1.8" interline UXGA monochrome
progressive CCD: ICX274AQ progressive CCD: ICX274AL
Total picture elements
Chip size
Cell size
Scanning system
Vertical frequency (Frame rate)
Horizontal frequency
Pixel frequency
Noise level at 8bit output
at 10bit output
at 12bit output
Minimum scene illumination 7.27 Lux at F1.2, 15.31668Hz 0.16 Lux at F1.2, 15.31668Hz
Sync. System
Video output Digital 8, 10 or 12 bit Raw or RGB 8 bi Digital 8, 10 or 12 bit Raw data
Interface
Protocol
Exposure time
ALC
Gain
Gamma
AOI function
Smear reduction
Color interpolation Available on RGB output Not available
White Balance function Auto, manual and push to set white balance Not available
is available on both Raw data output and RGB output
Trigger mode
Communication
I/O's
Auto IRIS lens control
Power Input voltage
Consumption
Dimensions
Optical filter IR cut filter on No filter
Optical center accuracy
Material
Lens mount
Connectors
Camera mount screws
Weight
Operational Lower limit
Higher limit
Storage temerature
Vibration
Shock
Standard compliancy
RoHS
Approximately 170 g
Active picture elements
Electronic
specifications
Mechanical
specifications
Environmental
specifications
C mount
RJ45 connecor
Power/IO connector: HR10A-10R-12PB (Hirose) or equivalent
DC IRIS lens connector: M1951 (EMUDEN) or equivalent
Two 1/4" Tripod screw holes (one each on top and bottom plate)
Sixteen M4 screw holes (four each on top, bottom and both sides plate)
(Auto detection with power/IO connector prioritized)
Less than 6.8 W
50 (H) x 50 (W) x 53.5 (D) mm excluding connectors
Positional accuracy in H and V directions: +/- 0.3 mm
Rotational accuracy of Ha nd V: +/- 1.5 deg.
Aluminum (AC)
Selectable ON/OFF via the communication
Edge preset trigger, pulse width trigger (unlimited long exposure)
UART communication through Ethernet port
Three opt isolated inputs and five opt isolated outputs
Not available
+10.8 to +26.4Vdc through power/IO connector or Power Over Ethernet
Preset trigger mode: 10 useconds to 16,777,216 useconds
Pulse width mode: 10 useconds to Unlimited
Auto iris lens, electronic iris and AGC (ON/OFF)
0 to 20.4 dB
Gamma 1.0 (Factory default) or downloadable gamma table
Programmable AOI setting via the communication
<= 12 Digit (Gain 0 dB)
<= 48 Digit (Gain 0 dB)
Internal
PoE : IEEE802.3af CLASS3 (1000BASE-T)
GigE Vision 1.2 and GenICam 2.0 compliant
Preset continuous mode: 10 useconds to 16,777,216 useconds
0.29261 to 61.26674 Hz changeable via the communication
Maximum frame rate is depending on the AOI setting
Maximum frame rate of the camera (61.26674 Hz) is 230 vertical resolution AOI setting
19.176 kHz
36.818175 MHz
<= 3 Digit (Gain 0 dB)
1688 (H) x 1246 (V)
UXGA: 1624 (H) x 1236 (V)
*EV-G200B1: With respect to the entered size, the 15 pixels above and below, and the 0 to 14th pixels and 1609th
to 1623rd pixels on the left and right sides will be blacked out.
*EV-G200C1: RAW data: With respect to the entered size, the 19 pixels above and below, and the 0 to 18th
pixels and 1605th to 1623rd pixels on the left and right sides will be blacked out.
RGb 8bit: With respect to the entered size, the 18 pixels above and below, and the 0 to 17th pixels and 1604th to
1623rd pixels on the left and right sides will be blacked out.
Additionally, the 2 pixels above and below, the 18th,19th, 1602nd, and 1603rd pixels within the blackened area will
be invalid (it is recommended that this area not be used for testing).
8.5 (H) x 6.8 (V) mm
4.4 (H) x 4.4 (V) µm
Progressive
15.31668 Hz at full resolution
EMS: EN61000-6-2, EMI: EN55011 Group 1 Class A
/ FCC 47CFR Part 15 Subpart B Class A（Verification） / ICES-003（Class A）
RoHS compliant
Environmental temperature -5 deg. C
Camera housing temperature (Top plate): 70 deg. C (Check "Operational temperature and power consumption")
Environmental temperature -30 to 65 deg. C
20Hz to 200Hz to 20Hz (5min./cycle), acceleration 10G, 3 directions 30 min. each
Acceleration 38G, half amplitude 6ms, 3 directions 3times each

7
EV-G030B1 / EV-G200C1 / EV-G200B1
Specifications Rev. 1.00
1.2.1 Spectral Sensitivity Characteristics
EV-G200B1
EV-G200C1 (with IR cut filter)
1
0.8
0.4
0.6
0.2
0400 500 600 700
Relative Response
Wave length [nm]
B
GR
IR cut filter
1
0.8
0.4
0.6
0.2
0400 500 600 700 800 900 1000
Relative Response
Wave length [nm]

8
EV-G030B1 / EV-G200C1 / EV-G200B1
Specifications Rev. 1.00
1.3 Operational temperature
The temperature of the camera, which is the temperature of the inside of the camera and the case temperature, will
be change depending on the usage of the camera.
Please use the this camera under below conditions:
Operational temperature: Camera housing temperature (Top plate) is less than 70 deg. C
When use this camera, please set up the camera proper way to radiate heat, which is the housing top plate
temperature is less than 70 deg. C.
The case heat management becomes keep the heat rating of the electronic components of the camera.
Temperature measuring point at
the housing top plate

9
EV-G030B1 / EV-G200C1 / EV-G200B1
Specifications Rev. 1.00
2 Connector specifications
2.1 RJ45 connector
Caution: This product is a PoE type. Apply power (+10.8 to 26.4Vdc) through the power/IO connector when PoE is
not supported.
Note: Recommend to lock down the screw to the camera with 0.18 N・m torque when connect the screw lock LAN
cable to the camera
Pin assignment
Note. Power supply connection comprise PoE (IEEE802.3af).
Pin No. Signal name
1TA+
2TA-
3TB+
4TC+
5TC-
6TB-
7TD+
8TD-

10
EV-G030B1 / EV-G200C1 / EV-G200B1
Specifications Rev. 1.00
2.2 LED information
Power ON the camera Green LED: Blinking
1Gb transferring
Yellow LED: OFF, Green LED: Blinking 100Mb transferring
NIC, HUB or LAN cable is not support 1Gb. Please use 1Gb supported NIC, HUB and LAN cable.
Please check the NIC and HUB setting is “1Gb transferring” when use with 1Gb supported NIC and
HUB.
When snapping of the CAT5e cable, possibility to change the transferring speed from 1Gb to 100Mb.
Please change the CAT5e cable.
Yellow LED Green LED Status
Orange light ON Green light ON Power ON
Orange light ON Green light blinking 1Gb transfering
Light OFF Green light blinking 100Mb transfering

11
EV-G030B1 / EV-G200C1 / EV-G200B1
Specifications Rev. 1.00
2.3 Power/IO connector
Connector: HR10A-10R-12PB (Hirose) or equivalent.
This connector is for DC power input and the input and output signals.
Pin assignment
Note.1: All I/Os (Pin number 3 through 10) are user assignable.
Note.2: DO NOT connect or disconnect the power/IO connector while the power input though PoE.
No. Signal type IO direction Spec. Initial signal
1 POWER IN GND - GND -
2 POWER IN - +10.8 to 26.4Vdc -
3 OUT0_AUX_OP OUT Opt. Isolated FameTriggerWait out
4 OUT1_AUX_OP OUT Opt. Isolated ExposureActive out
5 OUT2_AUX_OP OUT Opt. Isolated Open
6 OUT3_AUX_OP OUT Opt. Isolated Open
7 OUT4_AUX_OP OUT Opt. Isolated Open
8 IN0_AUX_OP IN Opt. Isolated TRG In
9 IN1_AUX_OP IN Opt. Isolated Open
10 IN2_AUX_OP IN Opt. Isolated Open
11 IO VCC IN - IO VCC -
+3 to +26.4Vdc
12 IO GND - IO GND -
Refer Fig. 3
Fig. 1
12pin connector

12
EV-G030B1 / EV-G200C1 / EV-G200B1
Specifications Rev. 1.00
2.3.1 Input signal
TRG IN: Input the trigger signal
High: Voltage of the “IO VCC IN”
Low: Smaller than 0.4V
2.3.2 Output signals
Set the output signals from the power/IO connector.
The following six output signals are selectable with the software or communication.
A) FrameTriggerWait
The user can check the camera conditions, which are the camera expose and the image output
processing by the trigger signal with this FrameTriggerWait signal.
a) High status (Voltage of the “IO VCC IN No processing by the trigger signal
The camera accepts the trigger signal
b) Low status (0V): The camera is expose and the image output processing by
the trigger signal
The camera default setting is the input trigger signal is INVALID while low status for this signal.
When the exposure starts while the image output by next trigger signal, please change the camera setting
(Device code: 00H, Command: 13H) to accept the trigger signal while the image output.
The noise appears on the image when start exposure while the image output. In this case, please change
the “H reset” for the exposure start mode (Device code: 00H, Command: 12H) to change the exposure
start point to next HD timing.
B) UserOutput
The status of this UserOutput signal can change with the “UserOutputValue”.
C) ExposureActive
The user can check the exposure time with this ExposureActive signal.
a) High status (Voltage of the “IO VCC IN”): The camera is exposing
b) Low status (0V): The camera is not expose
D) TriggerAuxiliary
This TriggerAuxiliary signal is the input trigger signal.
E) TriggerInternal
This TrigerInternal signal is the input trigger signal with the trigger delay time.
F) SensorReadOut
This SensorReadOut signal is the FVAL signal, which is the image output period of the time.
G) StrobeSignal
This StrobeSignal signal is the strobe control signal.

13
EV-G030B1 / EV-G200C1 / EV-G200B1
Specifications Rev. 1.00
2.4 DC IRIS lens connector
Not available for use with this camera.
Pin assignment
12
34
Fig. 2
DC IRIS lens connector
Pin No. Signal name
1 DAMP-
2 DAMP+
3 DRIVE+
4 DRIVE-

14
EV-G030B1 / EV-G200C1 / EV-G200B1
Specifications Rev. 1.00
3 I/O circuits
3.1 Input circuit
Response timing
Fig. 3 Input circuits
C
AMERA
R
espo
n
se
tim
e
11[ns]11[ns]11[ns]11[ns]
Tf
520[ns]545[ns]584[ns]689[ns]
Ts
100[ns]100 [ns]100[ns]100[ns]
Tr
3.0[us]3.0[us]2.8 [us]2.5[us]
Td
24
[
V
]
12
[
V
]
5.0
[
V
]
3.3
[
V
]
IO
_
VCC
10%
90%
Td Ts
T
r
Tf
USER INPUT
INPUT
OPTO ISOLATOR
SHARP：PC400J00000F
IO VCC
CAM VCC
If
INPUT
USER INPUT
Maximum consumption of If is 6 mA

15
EV-G030B1 / EV-G200C1 / EV-G200B1
Specifications Rev. 1.00
3.1.1 Example circuit for the input signal
US
ER INP
U
T
OPTO ISOLATOR
SHARP：PC400J00000F
I
O
V
CC
C
AMERA
C
AM V
CC
I
OG
ND
If
INP
U
T
OPTO ISOLATOR
SHARP：PC400J00000F
IO VCC
CAMERA
CAM VCC
IO GND
If
INPUT
IO VCC USER INPUT

16
EV-G030B1 / EV-G200C1 / EV-G200B1
Specifications Rev. 1.00
3.2 Output circuit
Response timing
Fig. 4 Output circuits
I
O
V
CC
US
ER
OU
TP
U
T
OU
TP
U
T
I
OG
ND
1
0
k
O
hm
C
AMERA
T
s
T
d
1
0
%
90%
T
r
Tf
OU
TP
U
T
US
ER
OU
TP
U
T
R
espo
n
se
tim
e
10.9[us]6.9[us]3.8[us]3.1[us]
Tf
2.8[us]2.8[us]2.2[us]2.2[us]
Ts
31.0[us]42.3[us]60.2[us]67.5[us]
Tr
28.4[us]35.2[us]30.4 [us]29.6[us]
Td
24
[
V
]
12
[
V
]
5.0
[
V
]
3.3
[
V
]
IO
_
VCC
OPTO ISOLATOR
SHARP：PC354NJ0000F

17
EV-G030B1 / EV-G200C1 / EV-G200B1
Specifications Rev. 1.00
4 Dimensions
1"-32UNF (C Mount)
53.5
50
50
φ32 40
Tripod screw depth 5 (Top and bottom plate)
4-M4 depth 4 (Top and bottom plate)
22.5
18
12
7.5
49
Unit: mm

18
EV-G030B1 / EV-G200C1 / EV-G200B1
Specifications Rev. 1.00
RICOH COMPANY, LTD.