RICOMAN R096501 User manual

ifl
0161-451-5924 [e-mail] www.ricoman.com
PRE INSTALLATION INSTRUCTIONS & GUIDELINES
• Ensure the supplied LED driver is used to connect to the AC input.
• Ensure the supplied screws are suitable for the specic ceiling.
• Do not disassemble or amend the structure of the luminaire as this can be dangerous and it would void your
warranty.
• The luminaire must be installed on a ceiling which should be rm enough to hold the weight of more than ve
times of the tting itself.
• The luminaire must not be installed above hot objects such as ovens to avoid damage to the tting.
• Ensure that ALL electrical connections are tight with no loose strands.
Pulsar LED Surface Mounted Spotlight
INSTALLATION INSTRUCTIONS
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION AND LEAVE
A COPY WITH THE END USER FOR FUTURE REFERENCE.
SAFETY INFORMATION – We recommend
that luminaires be installed by a fully qualied and
competent electrician who understands building
regulations and the current IEE wiring regulations. The
light source contained in this luminaire shall only be
replaced by the manufacturer or a qualied professional.
Before commencing any installation or
maintenance work, ensure that the electricity is
switched off at the mains.
IMPORTANT USER INFORMATION
Please install and use strictly in accordance with
these instructions. Make sure that you have all the
tools and equipment to complete the installation
safely and correctly. Improper installation could
cause harm to your property and/or person and
void your warranty.
It is the installer’s responsibility to consider re
and safety risks and take appropriate precautions.
Power Supply: AC200-240V
Power Factor: >0.90
CRI: >90Ra
Construction Material: Aluminium
RoHSRoHS
SPECIFICATION & DIMENSIONS
 
 
 



200
134
∅52
Part Code Kelvin Wattage Lumens Running
Current
R096501 3000K 12W 1202 DC250mA
R096502 4000K 12W 1206 DC250mA

ifl
0161-451-5924 [e-mail] www.ricoman.com
Before following these steps please ensure you have read and adhered to the guidelines and
information overleaf.
Pulsar LED Surface Mounted Spotlight
INSTALLATION STEPS
ENVIRONMENTAL PROTECTION
Waste Electrical & Electronic Equipment Regulations (WEEE) requires that any of our products showing this marking must not
be disposed of with other household or commercial waste. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate any such product from other waste types and recycle it responsibly at your local
facilities. Check with your Local Authority, Recycling Centre or retailer for recycling advice.
STEP 3 STEP 4
STEP 1 STEP 2
WARRANTY
This product is in warranty in the UK for a period of 5 year from the date of purchase. The guarantee is invalid in the case of improper use,
installation, tampering, removal of the Q.C. date label, installation in an improper working environment or installation not according to the
current edition of the IEE Wiring Regulations. Should this product fail during the warranty period, it will be replaced free of charge, subject
to the aforementioned conditions and return of the faulty unit. We do not accept responsibility for any installation costs associated with the
replacement of this product. Your statutory rights are not affected.
Ensure power is turned off.
A. Unscrew the anti-vandal
screw from the base.
B. Remove the base by
rotating anti-clockwise.
Drill two holes of 6mm diameter into the ceiling
according to the position of the base.
Connect the AC power to the connectors.
connectors
6mm
STEP 5 STEP 6
Align the driver box to
the counterpoint and
rotate clock-wise to x
onto the base. Screw
the anti-vandal screw
back into the base.
Lock the base with screw. Installation is complete.
Switch the power back on and test.
A
B
Fix the base on the ceiling using tapping screws.
Ø4x38
tapping
screw
counterpoint