RN-MTR II(Receiver), RN-TS100(Transmitter)
Thank you for buying this RITS-N Wireless Touch Switch. This product is a set of wireless transmitter/receiver switches to be installed in the
equipment requiring relay contact input to controlmotor e.g., of automaticdoor. Newly added Remote control lock function controls all sensor
input contact. To ensure the safe and correct use of this product, please read carefully all instructions throughout this manual.
1. Component & Specifications
Wireless Touch Switch (Waterproof Type)
2. How to Install Wireless Touch Transmitter Switch (RN-TS100)
Procedures
1. Input RN-TS100 into your receiver. (Input method: while pressing
the S/W Input Button on the receiver, press and hold the Wireless
Touch Switch for about 5 sec.)
2. Attach double-sided adhesive tape to the assembled wireless
touch switch.
3. Fix the wireless touch switch on the tempered glass or on the
desired place to be installed.
①Register button ③Power & Operation LED (Green Color)
④Power and output contact
Descriptions of Designations
① Register Button : While pressing and holding this switch, press and hold
the Transmitter Switch for about 5 seconds.
②Delete Button : While pressing and holding this switch, press and hold
the Transmitter Switch for approx. 2 seconds.
③ Power LED : LED light is moving during power on
④ Operation LED : LED light blinks when user press push button switches (Transmitter).
⑤ To delete all registered transmitters : Press and hold Delete & Register button at
same time for 5sec.
⑥Open maintenance function : If press Wireless touch switch for about 5 seconds,
the door will be open till press Wireless touch switch again.
* How to Register : Hold Register button and connect power till LED light blinks.
If delete this function, input same method.
* Factory default is off status.
②Delete button
3. Wireless touch switch Receiver Wiring
4. How to use Remote control
RN-FT240
Remote control
RN-MFT100
Multi-channel
Remote control
[Wiring 1] [Open signal holding function]
[Wiring 2] [Sensor Lock function]
Remote control IButton : Open signal
Remote control II Button : Open signal holding function off
Remote control III Button : Open signal holding function on
Remote control IButton : Open signal
Remote control II Button : Lock function on
Remote control III Button : Lock function off
Remote control IButton : Open signal
Remote control II Button : Lock function on / off
Remote control III Button : Open signal holding
function on / off
IButton
III Button
II Button
Automatic door controller
Automatic door controller
Wireless touch switch Receiver
Sensor output contact
Card reader output contact
Blue
Yellow
Automatic door controller
[Wiring 3] [Open signal holding function + Sensor Lock function]
Sensor output contact
Green
Blue
Automatic door controller
Blue
Yellow
Gray
Green
Twist together
Twist together
Connector
Connector
Connector
Connector
Inner Jumper
Inner Jumper
Inner Jumper
Inner Jumper
Yellow ⅹ2
Power (AC/DC12V~30V)
Gray ⅹ2
Power (AC/DC12V~30V)
Gray ⅹ2
Power (AC/DC12V~30V)
Gray ⅹ2
Power (AC/DC12V~30V)
Gray ⅹ2
Yellow ⅹ2
Receiver Jumper
Default value
Double-sided adhesive Wireless touch switch
(RN-TS100)
Wireless touch switch
(RN-TS100)
Double-sided adhesive
Tempered glass
Battery
PCB Waterproof Pad
Battery
Waterproof Pad
IButton
III Button
II Button
RN-TS100 (Transmitter) RN-MTR II (Receiver)
2 Pieces
Power connection wire(gray)
1EA
Double-sided adhesive tape
2 Pieces
Output contact wire(yellow)2EAFixing screws (Ø4ⅹ16)
2 EA
Fixing screws (Ø4ⅹ16)
2EABatteries 1.5V Size AAA
1 CopyUser’s Manual1 CopyUser’s Manual
SpecificationsComponents
Power supply 1.5V ⅹ 2 (Size AAA Battery) Power supply AC/DC12V~30V
AC125V/0.5A, DC30V/1ARelay contact capacityFM 447.600MHzRated frequency
Operating temp. -20℃~50℃Reception sensitivity -107 dBm
Size
10m Within(When installed in steel structures : 2m Within)Distance
Power consumption 60mA Under Power consumption 200mAUnder
Thickness 13mm
154 ⅹ43 ⅹ21
Please use double-sided adhesive when you install the wireless touch switch (Which improves waterproof function)
