Riva RC3402HD-6211IR User manual

www.rivatech.de
Specification subject to change without notice
RC3402HD-6211IR
Installation Guide

www.rivatech.de
Specification subject to change without notice

Precaution
Please read this manual carefully before installing the unit.
Never disassemble the camera. Unauthorized disassembly may
cause equipment failure or damage to the unit.
Please do not install the camera in a place exposed to direct
sunlight.
Do not operate the camera in environments beyond the specified
temperature.
Refer to “Environment Condition” on “ APPENDIX (A) :
SPECIFICATIONS ” in this manual.
Before applying power to the camera, check the power source to
ensure that it is within the specifications. Refer to “Electrical
Characteristics” on “ APPENDIX (A) : SPECIFICATIONS ”

Table of Contents
Precaution..................................................................................3
1. FEATURES ..............................................................................5
2. PACKAGE CONTENTS................................................................7
3. PART NAMES..........................................................................8
4. INSTALLATION.........................................................................9
4.1. Installing the camera ..................................................................... 9
4.2. Adjusting angle of the camera....................................................... 12
4.3. Setting the Image Attribute........................................................... 13
5. CONNECTIONS ......................................................................14
6. CONFIGURATION....................................................................16
6.1. Set up network environment ......................................................... 16
6.1.1. Generic IP Environment .......................................................... 16
6.1.2. Custom IP Environment .......................................................... 17
6.2. View video on web page ............................................................... 19
6.2.1. ActiveX Installation ................................................................ 19
6.2.2. View video using IPAdmin tool.................................................. 20
6.3. Reboot ...................................................................................... 21
6.4. Factory Default ........................................................................... 21
6.5. Safe Mode ................................................................................. 21
APPENDIX (A): SPECIFICATIONS ....................................................24
Summary.......................................................................................... 24
Electrical Characteristics..................................................................... 26
Environment Condition ........................................................................ 26
Mechanical Condition.......................................................................... 26
APPENDIX (B): POWER OVER ETHERNET ........................................27
PoE compatibility................................................................................ 27
Power Comparison............................................................................. 27
APPENDIX (C): DIMENSIONS ........................................................29
APPENDIX (D): HEXADECIMAL-DECIMAL CONVERSION TABLE.............30
REVISION HISTORY .....................................................................32

HD Series RC3402HD-6211IR Installation Guide
09-2013-B www.rivatech.de 5
1. FEATURES
Camera
Full HD Indoor IR Dome IP Camera
SONY EXMOR 1/2.9” 1080p CMOS Image Sensor
True Day / Night
WDR
Embedded IR Illuminator with Smart IR Control
Video
Video compression: H.264, MJPEG, 25/30FPS@1080p*
Dual streaming mode
Text Overlay
Analog Video Output for 3 minutes (only for installation purpose)
Unicast/Multicast
Network
10 / 100 Base-T Ethernet
RTSP/ HTTP protocol supported
Integration
Software Development Kit (SDK) available
ONVIF Compliant (Profile S)
General
Micro SD/SDHC slot
Power Over Ethernet (PoE)
Video Contents Analytics (VCA)
VCA Presence (Standard)
VCA Surveillance or other VCA extension license are available (Optional)
* If VCA is activated, frame rate is limit to max15fps@1080p. Limitation based on V.1.6.0
firmware release and could be changed without notice.

HD Series RC3402HD-6211IR Installation Guide
09-2013-B www.rivatech.de 6
Please note:
When using integrated LED illumination as major light source during night time, unwanted VCA
alarm events through flying insect’s activity are possible.

HD Series RC3402HD-6211IR Installation Guide
09-2013-B www.rivatech.de 7
2. PACKAGE CONTENTS
Please unpack the package carefully and handle the equipment with care.
The package contains:
Camera
DC Power Adaptor
Universal Plugs
Screws and anchor blocks
Quick Installation Guide
Camera Opener
Ferrite Core
DC Power Jack Cable
Installation Template
Cable Hole Cap
The contents above are subject to change without prior notice.
Note
i
구성
구성
구성
천정형
천정형

HD Series RC3402HD-6211IR Installation Guide
09-2013-B www.rivatech.de 8
3. PART NAMES
1Reset button
Use the button to restart the device or to reset it to Factory Default.
Refer to 6.3. Reboot and 6.4. Factory Default for more details.
2PAL/NTSC button
Pressing the button cycles through PAL, NTSC, and no video output mode: NO
video > PAL > NTSC. (Once the PAL/NTSC button is pressed, the video display
lasts for 3 minutes before it goes back to ‘no video output’ mode)
3Micro SD/SDHC slot
Supports up to 64GB. Recommend Class 6 and higher for HD recordings.
4Power Cable socket
Socket for the DC Power Jack Cable included in the package(Use DC12V adaptor
for power supply)
5LAN connector
RJ45 LAN connector for 10/100 Base-T Ethernet (PoE supported)
6Video Output connector
CVBS : 1.0Vp-p / 75 ΩBNC
FUNCTION
④


②
③
③
⑤
⑥
* Models herein and their appearance are subject to change without any prior notice.

HD Series RC3402HD-6211IR Installation Guide
09-2013-B www.rivatech.de 9
Opener
4. INSTALLATION
4.1. Installing the camera
How to remove the dome cover
Remove the dome cover with the opener included in the package like
the image below.
To prevent products from damage, place the camera on stable and
non-vibrating surfaces If the stability is in doubt, consult safety
personnel for reinforcements, and then proceed with the installation.
Caution
!
1) Place the installation template (outline
shown on the next page) included in the
package on the desired installation surface.
2) Drill holes in correct positions based on
the template paper, and insert anchor
blocks into the holes.
3) Remove the dome cover with the opener
included in the package.
4) Make sure the necessary cables including
a LAN cable and a power cable are properly
connected to the camera.
*It is recommended to install the ferrite
core provided in the package on the MCX
cable to minimize high frequency noise
level. Please refer to the note on the next
page for the detail.
5) Place the camera on the surface and
match the alignment holes with the inserted
anchor blocks.
6) Tighten the anchor blocks with screws.
7) Adjust the angle of the camera. Refer to
4.2.Adjusting angle of the camera for the
detail.
8) Attach the dome cover on main body and
push it toward main body till a “tick”sound
is heard.
Note
i
1) Insert the tip of the opener in the groove.
2) Give a little snap on the opener toward the upper right
direction. Then, the dome cover will be easily detached.

HD Series RC3402HD-6211IR Installation Guide
09-2013-B www.rivatech.de 10
How to close the dome cover
When placing the dome cover, look for carved trapezoid mark on
both dome cover and main body. Both trapezoids should be aligned
together when placing the cover like the image below.
MCX cable is the cable already linked inside the camera. The method
to install the ferrite core is as follows.
1. Open the ferrite core by lifting the clip.
2. Make one loop with the cable through the ferrite core. (See the
image below.)
3. Close the ferrite core to hold the cable loop into place.
Caution
!
?128,000 ?128,000
148,000
100,000
100,339
DIMENSION
?128,000 ?128,000
148,000
100,000
100,339
DIMENSION
Note
i

HD Series RC3402HD-6211IR Installation Guide
09-2013-B www.rivatech.de 11
Installation Template
(Unit: mm)
Installation template’s image size scale in this installation guide is
not 1:1.
The correct-size template design paper can be found inside the
package separately.
Caution
!

HD Series RC3402HD-6211IR Installation Guide
09-2013-B www.rivatech.de 12
4.2. Adjusting angle of the camera
1) Adjust the lens to the desired position by manually moving the camera gimbal
and the horizontal platform in the following directions.
2) Connect to the web page of the device to check its real-time image. Refer to
6.2. View video on web page for details about using its web page.
Refrain from continuously rotating the camera gimbal with
excessive force to a single direction as it is attached with a cable
inside the dome.
Caution
!
좌
우
상.하
회전
위치고정
①To adjust lens position, rotate the camera gimbal.
②To pan, rotate the horizontal platform.
③To tilt, tilt the lens by vertically adjusting the camera
gimbal.
②
①
③

HD Series RC3402HD-6211IR Installation Guide
09-2013-B www.rivatech.de 13
4.3. Setting the Image Attribute
Through the camera’s webpage, users can configure image settings. The menu
of image attribute is available under Video Appearance menu in Setup > Video &
Audio > Camera.
The following features can be adjusted: Brightness, Contrast, Saturation,
Sharpness and Orientation
For more detailed information, refer to the provided “RIVA Web Interface Manual
Full HD Line”.
All Manual’s and Installation Guides can downloaded from www.rivatech.de
homepage.

HD Series RC3402HD-6211IR Installation Guide
09-2013-B www.rivatech.de 14
5. CONNECTIONS
1LAN Connection
This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Use the Ethernet
cable (RJ45) to connect the device to a hub or a router in the network. When
the LAN cable is connected, the orange LED light will become solid and green
LED will blink every 250 millisecond. Refer to Appendix (B). Power over Ethernet
for more details.
Green LED Orange LED
FUNCTION
②
①
③

HD Series RC3402HD-6211IR Installation Guide
09-2013-B www.rivatech.de 15
2Power Connection
The camera can be powered from either 12VDC or PoE. If the camera is
powered via PoE, refer to Appendix (B). Power over Ethernet for more details. To
operate your camera using 12VDC, make sure the polarity is correct before
connecting the power cable. Incorrect connection may cause damages to the
device.
3Analog Video Out Connection
Use a 75 ohm video coaxial cable to connect to a monitor’s analog video input
and check the camera’s connection and its image focus at the installation site.
Be sure to press the output configuration button (PAL/NTSC button) to see the
video (Refer to 3. Part Names to check the location of the PAL/NTSC button).
The factory default is ‘no video output’; Press once to set the video to PAL, and
press again to set the video to NTSC. Pressing the button again will go back to
‘no video output’ mode, disabling the viewing through the analog video connection.
Once the PAL/NTSC button is pressed, the video display lasts for 3
minutes before it goes back to ‘no video output’ mode.
Note
i

HD Series RC3402HD-6211IR Installation Guide
09-2013-B www.rivatech.de 16
6. CONFIGURATION
6.1. Set up network environment
The default IP address of the device is 192.168.XXX.XXX. Users can identify the
IP address of the device from converting the MAC address’s hexadecimal numbers,
which is attached to the device. Be sure that the device and PC are on a same
area network before running the installation.
IP address : 192.168.xxx.xxx
Subnet mask: 255.255.0.0
6.1.1. Generic IP Environment
In case of generic private network environment where IP address
192.168.XXX.XXX are used, users may view the live streaming images on a web
page using the device’s default IP address:
1. Convert the device’s MAC address to the IP address. Refer to the Hexadecimal-
Decimal Conversion Chart at the end of the manual.
(The MAC address of the device is attached on the side or bottom of the
device.)
2. Start the Microsoft® Internet Explorer web browser and enter the address of
the device.
3. Web streaming and device configurations are supported through ActiveX
program. When the ActiveX installation window appears, authorize and install
the ActiveX.
MAC address = 00-13-23-01-14-B1 → IP address = 192.168.20.177
Convert the last two sets of hexadecimal numbers to decimal numbers.

HD Series RC3402HD-6211IR Installation Guide
09-2013-B www.rivatech.de 17
6.1.2. Custom IP Environment
IPAdminTool is a management tool, which automatically scans all of the network
products for users to perform administrative tasks, which includes network
configurations, firmware update, device reboot, and device organizations.
IPAdminTool and the manual can download from www.rivatech.de homepage.
To modify the device’s default IP address for customized network area;
1. Find the device from the IPAdminTool’s list and highlight the device’s name.
2. Right-click the mouse and select IP Address; IP Setup window appears.
3. In the IP Setup’s window, information under Local Network information
displays the user/PC’s network area information. Those information need to
be incorporated to the IP Address, Subnet Mask, Gateway, and DNS boxes,
except the last 2 sets of IP Address, which are to be the unique numbers for
the device. Refer to the image above for the setting
4. Click Setup to complete the modification.
PC environment Info
Give new unique IP
address in last two sets

HD Series RC3402HD-6211IR Installation Guide
09-2013-B www.rivatech.de 18

HD Series RC3402HD-6211IR Installation Guide
09-2013-B www.rivatech.de 19
6.2. View video on web page
Type the proper IP address to view the live streaming images through a web
browser.
The default username and password is root / pass.
6.2.1. ActiveX Installation
1. When the browser asks to install the AxUMF software, click Install to
proceed.
2. When Setup installation pop-up window appears, click Install to proceed with
rest of installations.
Depending on system OS and Internet Explorer version, installation
experience may differ from one another. Figures described above are
from Windows 7, Internet Explorer 9 environment.
Note
i

HD Series RC3402HD-6211IR Installation Guide
09-2013-B www.rivatech.de 20
6.2.2. View video using IPAdmin tool
IPAdminTool and the manual can download from www.rivatech.de homepage.
IPAdminTool automatically searches all activated network encoders and IP
cameras and shows the product name, IP address, MAC address and etc.
1. From the IPAdminTool’s product list, select the device by highlighting it.
2. Right-click the mouse and select Web View.