RKI Instruments 35-3010RKA-06 User manual

rkiinstruments.com
35-3010RKA-06 Sample-Draw
Detector
Part Number: 71-0207RK
Revision: E
Released: 6/5/17

35-3010RKA-06 Sample-Draw Detector
WARNING
Read and understand this instruction manual before operating
detector. Improper use of the detector could result in bodily harm
or death.
Periodic calibration and maintenance of the detector is essential
for proper operation and correct readings. Please calibrate and
maintain this detector regularly! Frequency of calibration
depends upon the type of use you have and the sensor types.
Typical calibration frequencies for most applications are between
3 and 6 months, but can be required more often or less often
based on your usage.

35-3010RKA-06 Sample-Draw Detector
Product Warranty
RKI Instruments, Inc. warrants gas alarm equipment sold by us to be free from defects in
materials, workmanship, and performance for a period of one year from date of shipment
from RKI Instruments, Inc. Any parts found defective within that period will be repaired
or replaced, at our option, free of charge. This warranty does not apply to those items
which by their nature are subject to deterioration or consumption in normal service, and
which must be cleaned, repaired, or replaced on a routine basis. Examples of such items
are:
Warranty is voided by abuse including mechanical damage, alteration, rough handling, or
repair procedures not in accordance with the operator’s manual. This warranty indicates
the full extent of our liability, and we are not responsible for removal or replacement costs,
local repair costs, transportation costs, or contingent expenses incurred without our prior
approval.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY AND ALL OTHER
WARRANTIES AND REPRESENTATIONS, EXPRESSED OR IMPLIED,
AND ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF
RKI INSTRUMENTS, INC. INCLUDING BUT NOT LIMITED TO, THE
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. IN NO EVENT SHALL RKI INSTRUMENTS,
INC. BE LIABLE FOR INDIRECT, INCIDENTAL, OR CONSEQUENTIAL
LOSS OR DAMAGE OF ANY KIND CONNECTED WITH THE USE OF
ITS PRODUCTS OR FAILURE OF ITS PRODUCTS TO FUNCTION OR
OPERATE PROPERLY.
This warranty covers instruments and parts sold to users by authorized distributors,
dealers, and representatives as appointed by RKI Instruments, Inc.
We do not assume indemnification for any accident or damage caused by the operation of
this gas monitor, and our warranty is limited to the replacement of parts or our complete
goods.
a) Absorbent cartridges d) Batteries
b) Pump diaphragms and valves e) Filter elements
c) Fuses

35-3010RKA-06 Sample-Draw Detector
Table of Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Flow System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Detection System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Mounting the Sample-Draw Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connecting the Sample Lines to the Sample-Draw Detector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Wiring the Sample-Draw Detector to a Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Start Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Introducing Incoming Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Setting the Zero Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Normal Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Low Flow Alarm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Preventive Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Replacing Components of the Sample-Draw Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Adjusting the Low Flow Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Calibration Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Preparing for Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Setting the Zero Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Setting the Response Reading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Returning to Normal Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

35-3010RKA-06 Sample-Draw Detector • 1
Overview
This manual describes the 35-3010RKA-06 sample-draw detector. This manual also
describes how to install, start up, maintain, and calibrate the detector. A parts list at the
end of this manual lists replacement parts and accessories for the sample-draw detector.
Specifications
Table 1 lists specifications for the 35-3010RKA-06.
WARNING: When using the 35-3010RKA-06, you must follow the instructions and
warnings in this manual to assure proper and safe operation of the
35-3010RKA-06 and to minimize the risk of personal injury. Be sure to
maintain and periodically calibrate the 35-3010RKA-06 as described in this
manual.
Table 1: Specifications
Target Gases & Detection Ranges Combustible Gas: 0 - 100% LEL
Hydrogen Sulfide (H2S): 0 - 100 ppm
Input Power 24 VDC
Current Draw 240 mA
Output Signals 4-20 mA each channel
Construction (housing) Fiberglass/polyester (NEMA 4X)
Dimensions 15.44 in. H x 12.55 in. W x 8.31 in. D
Weight 14 lbs.
Sampling Method Sample-draw
Sample Flow 1.2 SCFH (nominal)
Response Time 90% in 30 seconds
Accuracy Combustible Gas:
± 5% of reading or ± 2% LEL (whichever is greater)
Hydrogen Sulfide (H2S):
± 5% of reading or ± 2 ppm H2S (whichever is greater)

2 • 35-3010RKA-06 Sample-Draw Detector
Description
This section describes the components of the 35-3010RKA-06 sample-draw detector. The
sample-draw detector consists of the housing, flow system, and detection system.
Figure 1: Sample-Draw Detector Component Location
Housing
The sample-draw detector’s fiberglass housing is weather- and corrosion-resistant. It is
suitable for installation where general purpose equipment is in use. The housing door is
hinged on the left side and is secured by two latches on the right side.
Four mounting feet are attached to the back of the housing (one at each corner). Use the
mounting feet to install the housing to a vertical surface. Use the two conduit hubs on the
bottom of the housing to make wiring connections.
Hydrophobic
Filter (AcroPak)
Flow
Block
H2S Sensor
Amp 1
Pump
Preamp
Circuit
Board
LEL Transmitter
Charcoal Filter
CO Dummy Plug
Combustible
Sensor
Oxygen Dummy
Plug
Amp 2
3/4 Conduit Hub, 2X
Exhaust Fitting For 1/4"
OD Rigid Tubing
Inlet Fitting For 1/4" OD
Rigid Tubing
Main Circuit Board
Reset Switch

35-3010RKA-06 Sample-Draw Detector • 3
An aluminum subpanel is mounted to the interior of the housing. The sample-draw
detector’s internal components are mounted to the subpanel.
Flow System
The sample-draw detector’s flow system consists of the INLET fitting, hydrophobic filter,
charcoal filter, pump, flowmeter, bypass valve, status lights, pressure switch, flow block,
and EXHAUST fitting (see Figure 1). Figure 2 illustrates how the gas sample moves
through the flow system.
Figure 2: Sample-Draw Detector Flow Diagram
INLET Fitting
The INLET fitting on the bottom of the housing allows the gas sample to enter the sample-
draw detector. The INLET fitting accepts 1/4 in. rigid tubing. See “Installation” on page 9
for instructions to connect tubing to the INLET fitting.
Hydrophobic Filter
The hydrophobic filter is to the left of the main circuit board. It is held in place by a metal
clip. It prevents water and other liquids from contaminating the flow system. Replace the
filter when it appears dirty, discolored, or clogged. If a liquid other than water is drawn
into the filter, replace the filter as soon as possible.
Oxygen
Dummy
Plug
Hydrophobic
Filter
Inlet
Exhaust
Pump
CO
Dummy
Plug
Flow meter
Flow Block
Bypass
Valve
H2S
Pressure Switch
Charcoal
Filter LEL

4 • 35-3010RKA-06 Sample-Draw Detector
Charcoal Filter
The charcoal filter is located in the top left corner of the enclosure. It is held in place by a
metal clip. The charcoal filter is placed after the H2S sensor and before the CO sensor (if
one is installed) in the flow system. It scrubs out interfering gases which may cause the
CO sensor to respond, such as H2S or certain hydrocarbons. It is included in this version
of the sample draw detector in case a CO sensor is added in the field. If a CO sensor is
added in the field, a new charcoal filter should also be installed.
Pump
The pump is located to the left of the main circuit board near the bottom left of the
sample-draw detector. The pump pulls the gas sample into the sample-draw detector. The
pump operates on 24 VAC, which is generated from the 24 VDC supplied to the sample
draw detector.
Flowmeter
The flowmeter is attached to the main circuit board near the top left corner (see Figure 4).
A ball in the flowmeter column indicates the flow rate to the sensors. The flowmeter
measures the flow in the range 0.2 to 2.0 SCFH (Standard Cubic Feet per Hour). Although
the sample-draw detector will operate down to a flow of 0.6 SCFH, the optimum flow rate
is 1.2 SCFH.
Bypass Valve
The bypass valve is to the left of the flowmeter. The bypass valve adjusts the flow rate to
the sensors. Use a flat-blade screwdriver to adjust the bypass valve.
NOTE: The bypass valve allows fine adjustments of the flow rate. For a wider range of
adjustment, use the flow adjust potentiometer (see Figure 4).
Status Lights
Two status lights are above the flowmeter.
Pilot Light
The green Pilot light is on when the sample-draw detector is receiving power.
Fail Light
The red Fail light is on when the sample flow rate is below the low flow level.
NOTE: The factory set low flow level is 0.6 SCFH (±0.2). See “Adjusting the Low Flow
Setting” on page 18 for instructions to adjust this setting.
Pressure Switch
The pressure switch is mounted to the opposite side of the main circuit board. The
pressure switch monitors the flow rate to the sensors.
If the flow rate falls below the preset low flow level, the pressure switch causes the fail
relay to interrupt the signal in the 4-20 mA line for the H2S channel. This causes a
downscale reading at the monitor on this channel. The low flow level is factory-set at 0.6
SCFH (±0.2 SCFH).
NOTE: There is no low flow indication for the LEL channel.

35-3010RKA-06 Sample-Draw Detector • 5
Flow Block
The flow block is located in the lower right corner of the sample-draw detector. All the
sensors are installed in the flow block. The flow block routes the sampled air to each
sensor.
EXHAUST Fitting
The EXHAUST fitting on the bottom of the housing allows the gas sample to exit the
sample-draw detector. The EXHAUST fitting accepts 1/4 in. rigid tubing. See
“Installation” on page 9 for instructions to connect tubing to the EXHAUST fitting.
Detection System
The detection system consists of the gas sensors, LEL transmitter, preamp circuit board,
and the main circuit board.
Combustible Gas Sensor
The combustible gas sensor is installed in the lower left of the flow block. The combustible
gas sensor includes the sensing elements, flame arrestor, connector, and sensor leads.
Sensing Elements
Two sensing elements are protected within the sensor assembly. Through a series of
thermal and electronic reactions, these elements produce an output that is proportional to
the detection range of the sample draw detector. The LEL transmitter converts the output
to a 4 - 20 mA signal which can be used by a recording or monitoring device.
The porous flame arrestor allows the gas sample to enter the sensor assembly and contact
the sensing element. The flame arrestor also contains sparks within the sensor.
Connector
The top of the sensor includes five pins that plug into the socket connector. This connector
allows you to replace the sensor without disconnecting the wiring. The sensor leads are
soldered to the connector.
Sensor Leads
Four color-coded leads extend from the connector. The leads allow you to connect the
combustible gas sensor to the main circuit board.
Oxygen Sensor
The oxygen sensor is installed in the lower right of the flow block. In the 35-3010RKA-06,
the oxygen sensor position in the flow block is occupied by a dummy sensor.
Carbon Monoxide Sensor
The carbon monoxide gas sensor is installed in the upper left side of the flow block. In the
35-3010RKA-06, the carbon monoxide sensor position in the flow block is occupied by a
dummy sensor.
Hydrogen Sulfide Gas Sensor
The hydrogen sulfide gas sensor position is located in the upper right side of the flow
block.

6 • 35-3010RKA-06 Sample-Draw Detector
Figure 3: LEL Transmitter
LEL Transmitter
The LEL transmitter is mounted above the main circuit board. It consists of the span pot,
zero pot, one internally wired terminal strip, and the test points.
Span/Zero Pots
The span and zero pots are located at the bottom edge of the transmitter and are used for
calibration. Use the span pot to make adjustments to gas response readings and the zero
pot to make adjustments to the zero reading.
Transmitter Interconnect Terminal Strip
The transmitter interconnect terminal strip is the seven-point terminal strip near the right
edge of the transmitter. The transmitter is factory wired to the sensor and main circuit
board.
Test Points
The test points are located on the left side of the transmitter and are labeled TP+ and TP-.
A 100 mV - 500 mV output is available at these test points for use during calibration.
Preamp Circuit Board
The preamp circuit is used to connect the H2S sensor to the main circuit board and to
secure the sensor in the flow block. Two cables mate to the main circuit board: the one on
the left is for the CO sensor signal and the one of the right is for the H2S sensor signal.
Since there is no CO channel, the cable on the left is not used.
LEL Transmitter
Interconnect
Terminal Strip
Zero Pot
Span Pot
Test Point TP-
Test Point TP+

35-3010RKA-06 Sample-Draw Detector • 7
Main Circuit Board
Figure 4: Main Circuit Board
The main circuit board includes the interconnect terminal strip, sensor/transmitter
terminal strip, amp 1 circuit, amp 2 circuit, pump terminal strip, relay, and reset switch.
NOTE: The flowmeter and status lights are mounted to the main circuit board but are
considered part of the flow system.
Interconnect Terminal Strip
The interconnect terminal strip is the sixteen-point terminal strip near the bottom edge of
the main circuit board. Use the interconnect terminal strip to connect the sample-draw
detector to a controller.
Sensor/Transmitter Terminal Strip
The sensor/transmitter terminal strip is the sixteen-point terminal strip near the right
edge of the circuit board. Use the transmitter terminal strip to connect sensors or
transmitters to the main circuit board.
NOTE: The sensors and transmitters are factory wired to the sensor/transmitter
terminal strip. See “Wiring the Sample-Draw Detector” on page 10 for all wiring
procedures related to the sample-draw detector.
Test Point CAL + 2
Amp1
(CO)
Zero Span Zero
Fail LED
Sensor/Transmitter
Terminal Strip
PressureSwitch
Reset
Switch
Pilot LED
Amp2
(H2S)
Span
Test Point CAL + 1
Test Point CAL -2
Test Point CAL - 1
ACTerminal
Strip Not Used
Interconnect Terminal
Strip
Low Flow Adjust
Flow Adjust Pot
Flowmeter
Pump Terminal Stip
Relay

8 • 35-3010RKA-06 Sample-Draw Detector
Amp 1 and Amp 2 Circuits
These circuits are located to the left of the sensor/transmitter terminal strip. They each
include test points, a zero pot, and a span pot. Amp 1 is on the left and is for the CO
channel. Amp 2 is on the right and is for the H2S channel. Since there is no CO channel,
Amp 1 is not used.
The zero and span pots are used during calibration. Use the span pot to make adjustments
to gas response readings and the zero pot to make adjustments to the zero reading.
The test points are labeled CAL-1 and CAL+1 for the CO channel and CAL-2 and CAL+2
for the H2S channel. A 100 mV - 500 mV output is available at the H2Stest points for use
during calibration. No output is available at the CO test points.
Pump Terminal Strip
The pump terminal strip is the four-point terminal in the top left corner of the circuit
board. Use the pump terminal strip to connect the pump and pressure switch to the main
circuit board.
NOTE: The pump and pressure switch are factory-wired to the circuit board. See
“Wiring the Sample-Draw Detector” on page 10 for all wiring procedures related
to the sample-draw detector.
Relay
The relay is approximately in the middle of the circuit board. The relay is a four pole,
double-throw (4PDT) relay and is rated for 2 amps at 25 VDC (resistive). If the pressure
switch senses a low flow condition, the relay interrupts the 4-20 mA signal from the H2S
channel which will cause a downscale reading at the controller or recording device.
NOTE: There is no flow fail indication for the LEL channel on the 35-3010RKA-06
Sample Draw Detector.
Reset Switch
A small reset button is located in the upper left corner of the main PCB. When a low flow
condition occurs, the pump will be shut off. To reset the low flow condition and start the
pump again, press and hold the reset switch for about 2 seconds, then release.

35-3010RKA-06 Sample-Draw Detector • 9
Installation
This section describes procedures to mount the sample-draw gas detector in the
monitoring environment and wire the sample-draw detector to power and an external
device.
Mounting the Sample-Draw Detector
1. Select the mounting site. Consider the following when you select the mounting site.
• Is there enough room to open the housing door and make wiring connections at
the bottom of the housing and tubing connections at the right of the housing?
• Make sure there is sufficient room to perform start-up, maintenance, and
calibration procedures.
Figure 5: Mounting the Sample-Draw Detector
2. Close and latch the housing door.
NOTE: The sample-draw detector is shipped with the mounting feet “tucked under” the
housing to protect the mounting feet during shipment.
3. Slightly loosen the screw that secures one of the mounting feet to the housing, then
rotate the mounting foot 180 degrees.
4. Tighten the screw that secures the mounting foot to the housing.
Ø .31 x .50 slot, 4X
8.31
.18
Tube Fitting for 1/4"
OD tube, 2X
3/4" Conduit Hub, 2X
10.00
12.55
Door Latch
15.44
14.94
14.55

10 • 35-3010RKA-06 Sample-Draw Detector
5. Repeat steps 3 and 4 for the remaining three mounting feet.
6. Position the sample-draw housing on a vertical surface at eye level (4 1/2 to 5 feet
from the floor).
7. Insert 1/4 in. or 5/16 in. screws through the slots in the mounting feet to secure the
housing to the mounting surface.
Connecting the Sample Lines to the Sample-Draw Detector
1. Attach 1/4 in. O.D. rigid polypropylene or rigid Teflon sample tubing to the INLET
fitting.
CAUTION: If you use flexible sample tubing (polyurethane is acceptable), use an appropriate
insert to seal the connection between the tubing and the INLET fitting.
2. Place the opposite end of the tubing at the sampling area.
CAUTION: Avoid loops or slumps in the incoming sample line. To reduce response time, keep the
incoming sample line as short as possible.
3. Attach rigid sample tubing to the EXHAUST fitting.
4. Route the opposite end of the tubing to an open area where the sample can safely
disperse.
Wiring the Sample-Draw Detector
WARNING: Always verify that the power source is OFF before you make wiring
connections.
1. Turn off the controller.
2. Turn off or unplug incoming power to the controller.
3. Unlatch and open the housing door of the sample-draw detector.
4. Guide a five-conductor 18 gauge, shielded cable or five 18 gauge wires in conduit
through one of the conduit hubs at the bottom of the sample-draw housing. If
necessary, use both hubs to bring the wires in making sure that all the wires for a
particular channel go through the same hub.
5. Connect the cable to the sample-draw detector’s interconnect terminal strip as shown
in Figure 6.
6. Close and latch the housing door of the sample-draw detector.
CAUTION: Leave the cable shield drain wire insulated and disconnected at the sample-draw
detector. You will connect the opposite end of the drain wire at the controller.
7. Route the cable or wires in conduit leading from the sample-draw detector to the
controller.
8. Connect the drain wire to an available chassis ground at the controller end. RKI
controllers typically have a ground stud that can be used to ground the cable’s drain
wire.

35-3010RKA-06 Sample-Draw Detector • 11
Figure 6: External (Field) Wiring, Sample-Draw Detector
Interconnect Terminal Strip
LEL
(Controller Transmitter
Terminals)
24 VDC
4/20 (Feedback)
+
H2S
(Controller Transmitter
Terminals) 24 VDC +
4/20 (Feedback)
Reset Switch
Sample Draw Housing
Main Circuit Board

12 • 35-3010RKA-06 Sample-Draw Detector
Figure 7: Internal (Factory) Wiring, Sample-Draw Detector
Black
IN STR UM EN TS
SENSOR
GRN
TP-
BLK
SP AN ZE RO
POWER/SIG
P/N 57 -1050RK
REV. 0
TP+
GND
24V
4-20
RED
WHT
Green
Red
White
Pressure Switch
Factory W ired
Pump
Factory
Wired
H2S Sensor PlugsInto
Far Side of Preamp
Circuit Board
LEL
Detector
LEL Sensor
Connector
CO
(Not
Used) H2S

35-3010RKA-06 Sample-Draw Detector • 13
Start Up
This section describes procedures to start up the sample-draw detector and place the
sample-draw detector into normal operation.
Introducing Incoming Power
1. Complete the installation procedures described earlier in this manual.
2. Verify that the power wiring to the controller is correct and secure. See the controller
operator’s manual.
3. Turn on or plug in the incoming power at the controller, then turn on the controller.
4. Verify that the controller is on and operating properly.
5. Verify that the Pilot light is on at the sample draw detector.
6. Verify that the flowmeter indicates a flow rate of approximately 1.2 SCFH. If
necessary, use the bypass valve or flow adjust potentiometer to adjust the flow rate.
NOTE: The following step tests for leaks in the sample line. This test may cause a low
flow condition at the sample-draw detector.
7. Verify that the incoming sample line is not leaking. To test the sample line, plug the
open end of the sample line with your thumb. If the flowmeter ball drops to the
bottom of the flowmeter, the incoming sample line is not leaking.
8. Remove your thumb from the sample line, press the pump reset switch, and verify the
flowmeter returns to a normal flow rate.
Setting the Zero Reading
CAUTION: If you suspect the presence of combustible gas, hydrogen sulfide, or an abnormal
oxygen condition (not 20.9%) in the monitoring environment, use the calibration kit
and the zero air calibration cylinder to introduce “fresh air” to the sample draw
adapter and verify an accurate zero setting.
1. Verify that the sample-draw detector is sampling a fresh air environment
(environment known to be free of combustible gas, H2S and of normal oxygen
content, 20.9%).
2. Open the housing door.
3. Set a voltmeter to measure in the millivolt (mV) range.
4. Check the zero reading for each channel.
For the LEL channel, plug the voltmeter leads into the test points on the LEL
transmitter. Plug the positive lead into the test point labeled TP+; plug the negative
lead into the test point labeled TP-.
For the H2S channel, plug the voltmeter into the test points in the AMP 2 section of the
main circuit board. Plug the positive lead into the test point labeled CAL+2; plug the
negative lead into the test point labeled CAL-2.
5. Verify a voltmeter reading of 100 mV (± 2 mV).
6. If necessary, use a small flat-blade screwdriver to adjust the zero pot until the
voltmeter reading is 100 mV (± 2 mV).
7. Close the housing door.

14 • 35-3010RKA-06 Sample-Draw Detector
Operation
Normal Operation
During normal operation, the Pilot LED will be on and the flowmeter will indicate about
1.2 SCFH. The current gas readings will be indicated at the controller. See the controller’s
operator’s manual for a description of the reading indications.
Low Flow Alarm
If the flowrate falls below 0.6 SCFH (±0.2 SCFH), then the sample draw detector will
initiate a low flow alarm. In a low flow alarm the Fail LED will turn on and the pump will
shut off. In addition, the H2S sensor signal to the controller will be interrupted by the
sample draw detector resulting in a failure indication for the H2S channel at the controller.
If a low flow alarm occurs, press the pump reset switch for about 2 seconds to restart the
pump, turn off the Fail LED, and resume proper sensor signal transmission to the
controller. If the condition continues, find the cause of the reduced flow, correct it, and
restart the pump with the pump reset switch. A flow reduction can be caused by a flow
blockage, a leak in the flow system, a malfunctioning pressure switch, or a malfunctioning
pump.
NOTE: There is no flow fail indication for the LEL channel on the 35-3010RKA-06.
Maintenance
This section describes maintenance procedures. It includes preventive maintenance
procedures. This section also includes procedures to troubleshoot the sample-draw
detector, replace components of the sample-draw detector, and adjust the low flow
setting.
Preventive Maintenance
This section describes a preventive maintenance schedule to ensure the optimum
performance of the sample-draw detector. It includes daily, monthly, and quarterly
procedures.
Daily
1. Verify that the pilot light is on.
2. Verify that the flowmeter indicates a flow rate of approximately 1.2 SCFH.
If necessary use the bypass valve or flow adjust potentiometer to adjust the flow rate
to 1.2 SCFH.
3. Verify a reading of 0%LEL for the combustible channel (100 mV at the LEL transmitter
test points) and 0 ppm for the H2S channel (100 mV at the amp 2 test points).
Investigate significant changes in the reading.

35-3010RKA-06 Sample-Draw Detector • 15
Monthly
This procedure describes a test to verify that the sample-draw detector responds properly
to the target gases.
Preparing for the response test
CAUTION: This procedure may cause alarms at the controller. Take appropriate action to avoid
this, such as entering the calibration mode at the controller or disabling external
alarms.
1. Verify that the controller is reading 0 for the combustible and H2S channels.
If the reading is not 0 on the combustible or H2S channels, set the zero reading as
described in “Start Up” on page 13, then continue this procedure.
2. Assemble the calibration kit as described in “Preparing for Calibration” on page 19.
Use of a 4-gas cylinder is recommended so that all channels may be checked at once.
Performing the response test
NOTE: This procedure describes the RKI calibration kit that includes a demand flow
regulator. A calibration kit that uses a calibration bag is also available.
1. Screw the regulator into the calibration cylinder.
2. Connect the calibration tubing from the regulator to the inlet line at or near the INLET
fitting. Gas will begin to flow.
3. After approximately one minute, verify that the reading for each channel at the
controller stabilizes within ± 20% of the concentration of the test sample. If the
reading is not within ± 20% of the test sample, calibrate the sample-draw detector as
described in “Calibration” on page 19.
4. Remove the calibration tubing from the inlet line, then reconnect the inlet line.
5. Store the calibration kit in a safe place.
Quarterly
Calibrate the sample-draw detector as described in “Calibration” on page 19.
Troubleshooting
The troubleshooting guide describes symptoms, probable causes, and recommended
action for problems you may encounter with the sample-draw gas detector.
NOTE: This troubleshooting guide describes sample-draw detector problems only. See
the instruction manual for the controller if it exhibits any problems.
Fail Condition
Symptoms
• The sample-draw detector’s Fail light is on.
• The controller is operating properly but indicates a reading well below zero on one or
more channels.
Probable Causes
• The sample-draw detector’s flow rate is too low because of an obstructed sample line,

16 • 35-3010RKA-06 Sample-Draw Detector
failed pump, etc.
• The sample-draw detector is malfunctioning.
• The sensor or transmitter wiring is disconnected or misconnected.
Recommended Action
1. At the sample-draw detector, set the correct flow rate with the bypass valve or flow
adjust potentiometer.
2. If you cannot set the correct flow rate, check the sample lines for obstructions or kinks.
3. Verify that the sensor and transmitter wiring are correct and secure. “Installation” on
page 9 describes detector wiring connections.
4. Calibrate the problem channel or channels as described in “Calibration” on page 19.
5. If the fail condition continues, replace the sensor from the problem channel or
channels as described later in this section.
6. If the fail condition continues, contact RKI Instruments, Inc. for further instruction.
Slow or No Response/Difficult or Unable to Calibrate
Symptoms
• One or more of the sensors respond slowly or does not respond during the monthly
response test.
• Unable to accurately set the zero or response reading on one or more of the channels
during the calibration procedure.
• One or more of the sensors requires frequent calibration.
NOTE: Under “normal” circumstances, the sample-draw detector requires calibration
once a quarter. Some applications may require a more frequent calibration
schedule.
Probable Causes
• The calibration cylinder is low, out-dated, or defective.
• The sample-draw detector’s flow rate is too low because of an obstructed sample line,
failed pump, etc.
• The sample-draw detector is malfunctioning.
Recommended Action
1. Verify that the calibration cylinder contains an adequate supply of a fresh test sample.
2. If necessary, set the correct flow rate with the bypass valve or flow adjust
potentiometer.
3. If you cannot set the correct flow rate, check the sample line for obstructions or kinks.
4. If the calibration/response difficulties continue, replace the sensor as described later
in this section.
5. If the calibration/response difficulties continue, contact RKI Instruments, Inc. for
further instruction.