RKI Instruments 82-5220 User manual

www.rkiinstruments.com
82-5220
24 VDC Solenoid ESTOP
Operator’s Manual
Part Number: 71-0569
Revision: P1
Released: 8/13/21

2 • 82-5220
Product Warranty
RKI Instruments, Inc. warrants gas alarm equipment sold by us to be free from defects in materials,
workmanship, and performance for a period of one year from the date of shipment from RKI
Instruments, Inc. Any parts found defective within that period will be repaired or replaced, at our
option, free of charge. Parts must be returned to RKI Instruments, Inc. for repair or replacement. This
warranty does not apply to those items which by their nature are subject to deterioration or
consumption in normal service, and which must be cleaned, repaired or replaced on a routine basis.
Examples of such items are:
Warranty is voided by abuse including mechanical damage, alteration, rough handling, or repair
procedures not in accordance with instruction manual. This warranty indicates the full extend of our
liability, and we are not responsible for removal or replacement costs, local repair costs, transportation
costs, or contingent expenses incurred without our prior approval.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY AND ALL OTHER
WARRANTIES AND REPRESENTATIONS, EXPRESSED OR IMPLIED, AND
ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF RKI
INSTRUMENTS, INC. INCLUDING BUT NOT LIMITED TO, THE WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO
EVENT SHALL RKI INSTRUMENTS, INC. BE LIABLE FOR INDIRECT,
INCIDENTAL OR CONSEQUENTIAL LOSS OR DAMAGE OF ANY KIND
CONNECTED WITH THE USE OF ITS PRODUCTS OR FAILURE OF ITS
PRODUCTS TO FUNCTION OR OPERATE PROPERLY.
This warranty covers instruments and parts sold to users only by authorized distributors, dealers and
representatives as appointed by RKI Instruments, Inc.
We do not assume indemnification for any accident or damage caused by the operation of this gas
monitor and our warranty is limited to the replacement of parts or our complete goods. Warranty
covers parts and labor performed at RKI Instruments, Inc. only, and does not cover field labor or
shipment of parts back to RKI.
a) Pump diaphragms and valves c) Batteries
b) Fuses d) Filter elements

82-5220 • 3
Table of Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
About the 82-5220 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
External Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Internal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Factory Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Field Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Start Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Normal Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Replacing the Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4 • 82-5220
Overview
This manual describes the 82-5220 emergency shutoff. It also describes how to install and start up the
device. A spare parts list at the end of this manual lists replacement parts.
About the 82-5220
The 82-5220 is a fixed-mounted device with a relay, stack light, and emergency stop button. It requires
24 VDC to operate. A relay inside the 82-5220 is field-wired into the power line of a user-supplied
solenoid valve. When the emergency stop button on the front of the housing door is pushed, power to
the connected solenoid valve is cut off. A set of remote relay contacts may optionally be used to cut off
power to the connected solenoid.
Specifications
Table 1 lists specifications for the sample drawing gas detector.
WARNING: When using the 82-5220, you must follow the instructions and warnings in this
manual to assure proper and safe operation of the 82-5220 and to minimize the risk of
personal injury.
Table 1: Specifications
Construction (housing) • PBT/PC blend
•NEMA4X
Dimensions 18.77 in. (477 mm) H x 8.09 in. (205 mm) W x 7.19 in. (183 mm) D
Weight 4.6 lbs.
Input Power for Device 24 VDC
Relay Contact Rating
(for solenoid valve
power wiring)
• 15 A at 120 VAC
• 12 A at 28 VDC

82-5220 • 5
Description
External Description
This section describes the external components of the 82-5220.
Figure 1: External Component Location
Housing
The 82-5220’s PBT/PC blend housing is weather- and corrosion-resistant. It is suitable for installation
where general purpose equipment is in use. The housing door is hinged on the left side and is secured
by two latches on the right side. A panel inside the housing allows for component installation and
mounting. Four mounting feet are attached to the back of the housing (one at each corner). The
mounting brackets are used to install the housing to a wall.
One conduit hub on the bottom of the housing is for external wiring connections.
Housing
3/4 NPT Conduit Hub
Stack Light
Emergency Stop Button

6 • 82-5220
Emergency Stop Button
The emergency stop button on the front of the 82-5220 cuts power to the connected solenoid valve
when it is pushed.
Reset a pushed button by turning it clockwise.
Stack Light
The stack light installed on the top of the housing indicates the status of the solenoid valve’s power
line. When the light is green, power is being applied to the solenoid valve. When the light is red, power
is not being applied to the solenoid valve.
Internal Description
This section describes the internal components of the 82-5220.
Figure 2: Internal Component Location
Relay
A DPDT relay installed on the right side of the 82-5220 controls the stack light’s LED color and also
controls the power to the solenoid valve.
Emergeny Stop Button Connections
The emergency stop button’s wiring connections are visible on the back of the door. They are factory
wired to the Field Wiring Terminal Strip.
+
INPUT
POWER
24 VDC
_
TOALARM
CON TACT S
Mounting Plate
FieldWiring
Terminal Strip
Fuse
SOLENOID
CON TROL
1 NC 2
Emergency Stop
Button Connections Relay

82-5220 • 7
Fuse
A 250V, 1A slow blow fuse is installed in the power line that runs to the stack light. The fuse holder is
secured to the right side of the housing with a zip tie.
Field Wiring Terminal Strip
The relay and emergency stop button connections are wired to a terminal strip located in the lower
right corner of the 82-5220. The terminal strip makes wiring to 24 VDC, the solenoid valve, and a
remote relay contact (optional) more accessible.
Installation
This sections describes how to mount and wire the 82-5220.
Mounting
1. Select the mounting site. When you select the mounting site, consider the following factors:
• Is a DC power source available?
• Is a vertical surface available to mount the 82-5220?
• Is there enough room to open the housing door and make wiring connections through the
conduit hub at the bottom of the housing?
• Is the stack light visible?
• Is the location easily accessible in case of an emergency?
2. The 82-5220 is shipped with the mounting feet positioned under the housing. Loosen the screws
that secure the feet to the housing, rotate the feet to their mounting position as shown in Figure 3,
then tighten the screws.
3. Position the 82-5220 on the vertical mounting surface.

8 • 82-5220
4. Insert 3/16 in. screws through the mounting slots to secure the housing to the mounting surface.
Figure 3: Outline & Mounting Dimensions
3/4 NPT Conduit Hub
Ø .23 x .3slot, 4X
8.09
6.04
7.19
11.41
18.77

82-5220 • 9
Factory Wiring
The figure below shows factory wiring connections. These wiring connections should not need
adjustment.
Figure 4: Factory Wiring
1
5
Relay
NC
NO
8
4
9
NC
NO
Black
C
Red
Red
-
INPUT
POWER
24 VDC
_+
Red
+
C
SOLENOID
CONTROL
Not Used
Red
Green
1NC 2
Red
Red
Red
TO ALARM
CONTACTS
Yellow
Red
Green
Emergency Stop
Button Contacts 14 13
Stack Light
Red
12

10 • 82-5220
Field Wiring
This section describes how to wire 24 VDC to power the 82-5220, how to wire a solenoid valve’s
power through the 82-5220, and how to wire a remote relay contact into the 82-5220 (optional).
1. Turn off or unplug power to the 82-5220.
2. Open the housing door.
Power Wiring
3. Guide a 2-conductor cable or 2 wires in conduit through the conduit hub on the bottom of the
housing. Use appropriate conduit fittings and construction technique for the environmental rating
of the housing. The housing is rated NEMA 4X.
4. Connect one end of both wires to the + and - terminals of a 24 VDC power source.
5. Connect the other end of both wires to the appropriate “Input Power 24 VDC” terminal on the
Field Wiring Terminal Strip as shown in Figure 5 below.
Solenoid Wiring
6. Guide a 2-conductor cable or 2 wires in conduit through the conduit hub on the bottom of the
housing. Use appropriate conduit fittings and construction technique for the environmental rating
of the housing. The housing is rated NEMA 4X.
7. Connect one end of the two wires to the “Solenoid Control” terminals on the Field Wiring
Terminal Strip as shown in Figure 5 and Figure 6 below.
8. Connect the other end of the wires to the + or line terminal on a 24 VDC or 115 VAC power source
and to the solenoid valve’s + or line input as shown in Figure 5 and Figure 6 below.
9. For a DC-powered solenoid valve, connect the - terminal on the 24 VDC power source to the
solenoid valve’s - input as shown in Figure 5 below.
10. For an AC-powered solenoid valve, connect the N terminal on the 115 VAC power source to the
solenoid valve’s N input as shown in Figure 6 below.
Remote Relay Contact Wiring
Connecting the 82-5220 to a remote relay contact is is not necessary for operation. Connecting the 82-
5220 to a remote relay contact provides another way to cut the power line to the solenoid valve. If you
do connect the 82-5220 to a remote relay contact, the relay contact set used must be normally open and
the relay must be configured as normally energized.
11. Remove the jumper from the Field Wiring Terminal Strip.
NOTE: If you are not connecting a remote relay contact to the 82-5220, the jumper must stay
installed.
12. Guide a 2-conductor cable or 2 wires in conduit through the conduit hub on the bottom of the
82-5220 housing. Use appropriate conduit fittings and construction technique for the
environmental rating of the housing. The housing is rated NEMA 4X.
13. Connect the wires to the “To Alarm Contacts” terminals on the Field Wiring Terminal Strip.
14. Guide the other end of the wires to the normally open remote relay contact. Use appropriate
conduit fittings and construction technique for the environmental rating of the relay contact’s
housing. RKI’s controllers are rated NEMA 4X.