RNR Marine T-Top Boat-Cover User manual

RNR-Marine, Inc. is the top dealer of quality TTopCovers.com
products (T-Top-Boat-Covers, T-Top-Storage-Curtains, Boat-
Shade-Kit, etc.) in the United States. TTopCovers.com products
are Manufactured and Warranted by LaPorte's Upholstery in
North Charleston, SC.
T-Top Boat-Cover
Your T-Top-Boat-Cover is patterned to custom-fit your specific
year, make and model of boat. The zipper side (Port or
Starboard) is selected at purchase and the cover made to your
order in the chosen material (Elite 9oz./sq.yd. or WeatheMax
8oz./sq.yd. fabric). Options include: Storage Bag, Tie-Down
Straps and Sand Bags (for lift storage).
RNR-Marine, Inc. | 636-G39 Long Point Road | Charleston, SC 29464 | 843-303-6928

First, locate the only royal blue webbing
strap located on your T-Top Boat Cover.
Attach the strap to the front center bar
beneath the canvas top. (See photos A-B.)
Note: If there is no
center bar to attach
strap to, an additional
connector strap is
needed. (See photo C.)
Next, find the two black webbing straps located on each side of the
blue strap, and attach the black straps to the right and left of the center
bar. The fabric between the straps should be
taut. Then, place the smaller section of your
T-top cover over the bow. Once your cover
has been properly installed for the first time,
you may slide the cover over the bow before
attaching the royal blue strap. (See photos F-G.)
Note: There are various types of bows on different boats. (See photos E-G.)
Place the portion of the cover that contains the draw rope over the port
side rub rail. Find the webbing strap that is located next to the forward
half of the zipper on the port side of the
cover. Connect this strap to the horizontal
bar found under the canvas top and posi-
tioned between the console and the helm
seat. (See photo H.) The material between the
webbing straps should be kept taut.
Note: These straps are adjustable and can
be tightened or loosened as necessary.
Take the larger section of the cover and place the portion that contains
the draw rope over the starboard side rub rail. Position the remaining
section of the cover over the motor or motors. Find the stern half of
the zipper and join to the forward half of the zipper located between
the console and helm seat zipping approximately one third of the way.
Your T-Top Boat Cover is
Ready to Assemble.
Setting up your T-Top Boat CoverTM
is an easy, one person operation.
After reading the instructions and
setting up your T-Top Boat Cover,
you’ll find that installing and
disassembling takes approximately
five minutes. T-Top Boat Covers are
manufactured for your specific
model. Our covers are uniquely
designed with one inch webbing and
an adjustable clip that allows
T-Top Boat Covers to fit models that
have both factory and aftermarket
T-tops. Plus, our adjustable one inch
webbing strap allows flexibility in
fastening the cover to different style
T-top frames.
Assembly Instructions
Getting started is easy.
A
B
Continued...
D
E F G
H
C
Standard Bow Projecting Bow Anchor Pulpit with Rails
❶
❷
❸
T-Top Boat Covers
LaPorte’s Upholstery, Inc.
4352 Bridge View Drive
North Charleston, SC 29405
Telephone [phone]
Fax [phone]
w w w . t t o p c o v e r s . c o m
INSTRUCTIONAL CD
is also available at nominal cost...
Call [phone] for details.

Next find the webbing
strap closest to the stern
zipper and attach this strap
to the same horizontal bar
between the console and
the helm. Then find the
webbing strap that is to the immediate left and attach this strap to the
center horizontal bar under the canvas top. (See photo J.) Continuing to
the immediate left, locate the third strap and attach this strap to the
horizontal bar under the canvas top on the starboard side and between
the console and helm seat. (See photos H-J.)
Depending on the size of your T-top cover,
there may be additional straps to secure. If
so, continue connecting the remaining
straps in a counter clockwise motion
to any horizontal bar found under the
canvas top. While stepping out of the
boat complete zipping the remaining
portion of the zipper. At the bottom of
the zipper is a draw rope which has loops on both ends.
Slide one end of the rope through a loop and draw the rope
tight. Make a clove hitch knot at the end of rope. (See photos K-M.)
Check to confirm that the cover
is securely fastened over the bow,
rub rails, aft corners, and motor. One
inch loops are installed around the
bottom of the cover for tie downs.
Tie downs are not included with the
cover. If cover fits loosely,
re-enter the boat to adjust one
inch webbing straps. Motor or
motors should be in a down
position for proper fit of cover.
(See photos N-O.)
T-Top Boat Covers
LaPorte’s Upholstery, Inc.
4352 Bridge View Drive
North Charleston, SC 29405
Telephone [phone]
Fax [phone]
w w w . t t o p c o v e r s . c o m
T-Top Boat Cover Add-On Options Available...Call [phone] For Pricing.
Your Warranty
T-TOP BOAT COVER LIMITED WARRANTY:
We guarantee top quality craftsmanship and material
against defects upon time of receiving a product. Our
warranty consists of one full year from the time of pur-
chase of the craftsmanship of the boat cover. Proper
installation and care of the boat cover must be main-
tained. In response to a defect, customer is responsible
for complete cost of freight to and from manufacturer.
T-Top Boat Covers are for storage only. Traveling with
cover will void warranty (it will be Manufacturer's final
discretion regarding care of cover).
All covers made with Sur LastTM material will receive an
additional limited warranty. This warranty covers Sur
Last fabric from becoming unserviceable because of loss
of color or strength from normal exposure conditions,
including sunlight, mildew or rot. This coverage does not
include labor. This additional warranty (relating to the
Sur Last fabric only) consists of a three year warranty
coverage which begins from date of purchase of cover.
All customers must call before returning a defective
boat cover to receive a confirmation number. Send
warranty claims to LaPorte's Upholstery, Inc.,
4352 Bridge View Drive, North Charleston, SC 29405.
I
J
K
L
M
N
O
Improperly Installed Cover
Optional Stern
Connector Strap
Properly Installed Cover
Storage Bag for Cover
Protect your T-Top Boat Cover
while not in use.
Connector Straps
Connector strap is used when boat’s T-top does not have a
front or aft center bar to attach webbing.
Note: One Connector Strap is included with the purchase of
your T-Top Boat Cover. For boats without exposed front and
aft center bars, additional strap purchase may be required.
Adjustable Tie Down Straps
Nine adjustable straps hold down
T-Top Boat Cover to trailer sides.
Special Notes: T-Top Boat Covers are
not a travel cover. Traveling with
cover in place will void warranty.
❹
❺