ROBLIN GRAPHIC MURALE 900 User manual

LibrettoIstruzioni
InstructionsBooklet
Mode d’emploi
Bedienungsanleitung
Gebruiksaanwijzing
NL
DE
FR
GB
IT
39
30
21
12
3
Graphic Murale 900

12GB
CONTENTS
Dear Customer,
If you follow the recommendations
contained in this Instruction Manual,
your appliance will give you constant
high performance and will remain
efficient for many years to come.
RECOMMENDATIONS AND SUGGESTIONS 13
CHARACTERISTICS 14
INSTALLATION 15
USE 18
MAINTENANCE 19

13GB
RECOMMENDATIONS AND SUGGESTIONS
INSTALLATION
• The manufacturer will not be held liable for any damages resulting
from incorrect or improper installation.
• The minimum safety distance between the cooker top and the
extractor hood is 650 mm.
• Check that the mains voltage corresponds to that indicated on the
rating plate fixed to the inside of the hood.
• For Class I appliances, check that the domestic power supply
guarantees adequate earthing.
Connect the extractor to the exhaust flue through a pipe of
minimum diameter 120 mm. The route of the flue must be as short
as possible.
• Do not connect the extractor hood to exhaust ducts carrying
combustion fumes (boilers, fireplaces, etc.).
• If the extractor is used in conjunction with non-electrical appliances
(e.g. gas burning appliances), a sufficient degree of aeration must
be guaranteed in the room in order to prevent the backflow of
exhaust gas. The kitchen must have an opening communicating
directly with the open air in order to guarantee the entry of clean
air.
USE
• The extractor hood has been designed exclusively for domestic
use to eliminate kitchen smells.
• Never use the hood for purposes other than for which it has ben
designed.
• Never leave high naked flames under the hood when it is in
operation.
• Adjust the flame intensity to direct it onto the bottom of the pan
only, making sure that it does not engulf the sides.
• Deep fat fryers must be continuously monitored during use:
overheated oil can burst into flames.
• The hood should not be used by children or persons not instructed
in its correct use.
MAINTENANCE
• Switch off or unplug the appliance from the mains supply before
carrying out any maintenance work.
• Clean and/or replace the Filters after the specified time period.
• Clean the hood using a damp cloth and a neutral liquid detergent.
650 mm min.

14GB
CHARACTERISTICS
Dimensions
Components
Ref. Q.ty Product Components
12d
2.1
2.2
12c
9
15
12a 7.2.1 11
11 HoodBody,completewith:Controls,Light,Blower,
Filters
2.1 1 Upper Section (optional)
2.2 1 LowerSection(optional)
81 DirectionalAirOutletgrille
91 Flange(optional)
15 1 Angle iron (optional)
16 1 Filtercover
Ref. Q.ty Installation Components
7.2.1 2 Upper Chimney Section Fixing Brackets
(optional)
11 6 WallPlugs (4optional)
11a 2 WallPlugsSB12/10
12a 6 Screws4,2 x44,4 (4 optional)
12c 10 Screws2,9x6,5 (6 optional)
12d 6 Screws2,9 x9,5 (4optional)
Q.ty Documentation
1 Instruction Manual
1
16
12c
11
12a
12d
8
11a

15GB
INSTALLATION
Walldrillingandbracketfixing
On the wall, draw
• a Vertical line up to the ceiling or upper limit, at the centre of the area in which the Hood is to be
fitted;
• a Horizontal line at a minimum of 960 mm above the Cooker Top.
• Mark a point (1) on the horizontal line, 200 mm to the right of the vertical reference line.
• Repeat this operation on the other side, checking that the two marks are level.
• Mark a reference point (2) as indicated at 180 mm from the vertical reference line and 362 mm
above the Cooker Top.
• Repeat this operation on the other side, checking that the two marks are level.
• Drill at the points (1) marked, using a ø 12 mm drill bit.
• Drill at the points (2) marked, using a ø 8 mm drill bit.
• Insert the bracket plugs 11a into the holes 1and screw into place.
• Insert plug 11 into hole 2.
To install a decorative chimney ( optional )
• Place bracket 7.2.1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the
centre (notch) with the vertical reference line.
• Mark the wall at the centres of the holes in the bracket.
• Place bracket 7.2.1 on the wall as shown at X mm below the first bracket (X = height of the upper
chimney section supplied), aligning the centre (notch) with the vertical line.
• Mark the wall at the centres of the holes in the bracket.
• Drill ø 8 mm holes at all the centre points marked.
• Insert the wall plugs 11 in the holes.
• Fix the brackets using the 12a screws (4,2 x 44,4) supplied.
11a
11
11
12a
22
180 180
250
200 200
960
362
X1÷2
7.2.1

16GB
(A)
(B)
Vr
9
16
12c
12d
8
Mounting the hood body
• Open the ducting panels.
• Disconnect the panel from the hood canopy by
sliding the fixing pin lever.(A)
• Remove the metal grease filters by turning the
handles provided.
• Adjust the two screws Vr, on brackets 11a, to a
minimum.(B)
• Hook the hood canopy onto the two brackets 11a.
• From inside the hood canopy, adjust the screws
Vr to set the Hood Canopy level.
• Tighten the safety screw 11.
Connections
DUCTED VERSION AIR EXHAUST SYSTEM
When installing the ducted version, connect the hood to the chimney using either a flexible or rigid
pipe, the choice of which is left to the installer.
• Insert the flange 9 (optional), on the hood body
outlet.
• Fix the pipe in position using sufficient pipe
clamps (not supplied).
• Remove any activated charcoal filters.
RECIRCULATION VERSION AIR OUTLET
To install the Recirculation Version of the hood, the optional Activated charcoal cartridge kit must be
purchased.
• Screw the filter cover onto the air outlet, using
four screws 12c (2.9 x 12.5).
• Fix the directional grille 8on the recirculation air
outlet using the 2 screws 12d (2,9 x 9,5) provided.

17GB
Flueassembly
The chimney can only be installed with exhausting hood
• Fasten the angle iron 15 to the hood canopy
using the screws 12d (2,9 x 9,5) provided.
Upper exhaust flue
• Slightly widen the two sides of the upper flue
and hook them behind the brackets 7.2.1, making
sure that they are well seated.
• Secure the sides to the brackets using the 4
screws 12c (2,9 x 6,5) supplied.
Lower exhaust flue
• Slightly widen the two sides of the flue and
hook them between the upper flue and the wall,
making sure that they are well seated.
• Fix the lower part laterally to the hood body
using the 2 screws 12c (2,9 x 6,5) supplied.
ELECTRICAL CONNECTION
• Connect the hood to the mains through a two-pole
switch having a contact gap of at least 3 mm.
• Remove the grease filters being sure that the connec-
tor of the feeding cable is correctly inserted in the socket
placed on the side of the fan.
12c
2.1
2.2
2
7.2.1
12c

18GB
L
S1
T1
T2
T3
T4
USE
Control Panel
The hood can be switched on pushing directly onto the requested speed without
firstly having to select 0/1 button.
KEY LED FUNCTIONS
L0/1 Light Turns lighting on and off.
T1 0/1 Motor on First speed.
When pressed for about 1 seconds the motor is
switched off.
Flashing 24h Changeover
This is enabled by pressing and holding the
button for approximately 5". It allows a
suction level of 100 m3/h with a noise level
of just 28dB(A). Can be enabled at any
speed, even with the hood turned off. To
disable, press and hold the button for
approximately 5".
T2 Speed on Second speed.
Flashing Delay (30')
Press the button for approximately 2" to enable automatic
shutdown with a 30' delay. Suitable to complete elimination
of any residual smells. Can be enabled at any speed and is
disabled by pressing the button briefly.
T3 Speed on Third speed.
T4 Speed Fixed Max. speed
Flashing Intensive speed.
Suitable for the strongest cooking vapours and odours. The
function becomes active when the button is pushed for about
2 seconds. After 10 minutes of functioning it turns off
automatically. This function can be interrupted by means of
pressing any of the buttons.
S1 Led Fixed Indicates that the Metal grease filters saturation alarm has
been triggered, and the filters need to be washed. The alarm
is triggered after 100 working hours. (Reset; check the
Maintenance-paragraph)
Flashing indicates that the activated charcoal odour filter saturation
alarm has been triggered, and the filter has to be replaced;
the metal grease filters must also be washed. The activated
charcoal odour filter is triggered after 200 working hours.
(Activation and Reset; check the Maintenance-paragraph)

19GB
REMOTE CONTROL (OPTIONAL)
The appliance can be controlled using a remote control
powered by a 1.5 V carbon-zinc alkaline batteries of
the standard LR03-AAA type.
• Do not place the remote control near to heat sources.
• Used batteries must be disposed of in the proper
manner.
MAINTENANCE
Grease filters
CLEANINGMETALSELF-SUPPORTINGGREASEFILTERS
Alarm signal reset
• Switch off the lights and extractor motor.
• Press button T3 for at least 3 seconds, until the leds start to flash.
Cleaning the filters
• The filters are washable and must be cleaned when led
S1 flashes or at least every 2 months of operation, or
more frequently for particularly heavy usage.
• Remove the filters one at a time by pushing them to-
wards the back of the group and pulling down at the
same time.
• Wash the filters, taking care not to bend them.
Allow them to dry before refitting.
• When refitting the filters, make sure that the handle is
visible on the outside.
Ducting panels
• Clean the outside using a damp cloth and neutral
liquid detergent.
• Clean the inside using a damp cloth and neutral
detergent; do not use wet cloths or sponges, or
jets of water; do not use abrasive substances.

20GB
Activatedcharcoalfilter(Recirculationversion)
REPLACING THE ACTIVATED CHARCOAL FILTER
• The filter is not washable and cannot be
regenerated. It must be replaced when led S1
flashes or at least every 4 months. The alarm
signal will only light up when the extractor
motor is switched on.
Alarm signal reset
• Switch off the lights and extractor motor.
• Press button T3 for at least 3 seconds, until the
leds start to flash.
Replacing the Filter
• Remove the metal grease filters
• Remove the saturated activated carbon filters
as shown (A).
• Fit the new filters (B).
• Replace the metal grease filters.
Alarm signal activation
• In Recirculation version Hoods, the Filter saturation alarm can be enabled on installation or at a
later date. Turn the Lights and the suction Motor off.
• Disconnect the Hood using the Main switch or the double-pole switch on the mains power supply.
• Restore the connection by pressing and holding T1.
• Release the button. All five LEDs are turned on
• Within 3 seconds press T1 until LEDs T1 and T4 flash in confirmation:
LED flashes twice - Activated charcoal filter saturation alarm ENABLED
LED flashes once - Activated charcoal filter saturation alarm DISABLED
Lighting
LIGHT REPLACEMENT
20 W halogen light.
• Remove the light cover by unfastening the
screws that hold it.
• Extract the lamp from the Support.
• Replace with another of the same type, making
sure that the two pins are properly inserted in
the lamp holder socket holes.
• Replace the light cover.
A
B