Rockford Fosgate DSR1 User manual

DSR1 PRODUCT OVERVIEW & APP SETUP
Step 2 - Non Vehicle-Specific Installation
The DSR1 comes pre-programmed as follows:
 • (4)Inputs
 • (8)ActiveOutputs:
   -Front(L/R)
   -Spare(L/R,signalderivedfromfrontinputs)
   -Rear(L/R)
   -Sub(L/R)
Subwooferisasummingofall4inputchannels.No
balance,nofade.Youwillneedtodownloadtheappif
youwanttorecongurethedeviceandtakeadvantageof
thecustomaudiotuningcapabilities.
Step 3 - Download the App
TotakeadvantageofthefullDSR1’stuningcapabilities,
downloadtheRockford Fosgate PerfectTune™app,
designedtorunonbothtabletsandmobiledevices.
Step 4 - App Setup & Tuning
Onceyouhavetheappinstalledontoyourdevice,the
setupprocesswillwalkyouthroughthenecessarysteps
forpairingthedevicetotheDSR1.Afterthepairingis
complete,theappwillcontinuetoprovideinstructionto
nalizethedesiredaudiotuneforthevehicle.
PLCOUTPUT
INPUTVEHICLE HIGH LOW
INPUT LEVEL
EXP
STATUS
USB
Output Harness
Punch Level Control
(sold separately)
USB Setup / Update Port Input Harness
Status Indicator
Expansion Port
Input Level Switch
Vehicle T-Harness
(sold separately)
IfyouplantouseDSR1inaMAESTROvehicle-specicinstallation,proceed
withsteps1-3below,thenfollowMaestroprogrammingabove.
PerfectTune™ App
Step 1 - Update DSR1
GetthelatestaudiofeaturesbyupdatingtheDSR1at
www.rockfordfosgate.com/products/details/dsr1.

INPUTVEHICLE HIGH LOW
INPUT LEVEL
EXP
STATUS
USB
INPUTVEHICLE HIGH LOW
INPUT LEVEL
EXP
STATUS
USB
INPUTVEHICLE HIGH LOW
INPUT LEVEL
EXP
STATUS
USB
HIGH LOW
INPUT LEVEL
HIGH LOW
INPUT LEVEL
HIGH LOW
INPUT LEVEL
Aftermarket Amps
Battery (+)
FRONT LEFT IN 1
Back of Factory Amplifier
(typically under seat)
Vehicle CAN-BUS
DSR1 “Vehicle” Connector
FRONT RIGHT IN 2
REAR LEFT IN 3
REAR RIGHT IN 4
B+ (constant +12v)
Remote Input +12v
T-HARNESS
(sold separately)
Chassis Ground
Remote Output +12v
AUX IN LEFT
AUX IN RIGHT
SPDIF IN
BLUE
BLUE / WHITE
YELLOW
BLACK
FRONT LEFT IN 1
PREAMP OUTPUTS DSR1 INPUTSDSR1 INPUTS
FRONT RIGHT IN 2
REAR LEFT IN 3
REAR RIGHT IN 4
B+ (constant +12v)
Remote Input +12v
Chassis Ground
Remote Output +12v
AUX IN LEFT
AUX IN RIGHT
SPEAKER LINE OUTPUTS
Add Bluetooth® audio with
RFBTRCA (sold separately)
Add Bluetooth® audio with
RFBTRCA (sold separately)
SPDIF IN
BLUE
Remote Output +12v
BLUE
BLUE / WHITE
YELLOW
BLACK
Aftermarket Amps
Battery (+)
May be needed if radio
doesn’t turn-on DSR1
+
–
+
–
+
–
+
–
Factory Amplifier
Optional “RFI2SW”
Data Port Radio
DSR1 FLEXIBLE INPUT CONFIGURATIONS
TheDSR1canbeutilizedout-of-the-boxwithhigh-level,low-level,orwithaT-harnessandvehicle
specicrmwareenablingintegrationwithoutlossoffactoryequippedcontrolsandfeatures.
illustrated by Eric Russell
Allowsforinstallationofaftermarket
amplierswithvehiclespecicrmware
andT-harnesswhileretainingfactory
radiocontrolsandfeatures.
FACTORY RADIO + THARNESS
Allowsforinstallationofaftermarket
ampliersinvirtuallyanyvehiclewitha
factoryradiousinghigh-levelinputs.
FACTORY RADIO
Allowsforinstallationofaftermarket
ampliersinvirtuallyanyvehiclewithan
aftermarketradiousinglow-levelinputs.
AFTERMARKET RADIO
IMPORTANT:
Followinstructions
onbackpageto
ashDSR1.

PLCOUTPUT INPUTVEHICLE HIGH LOW
INPUT LEVEL
EXP
STATUS
USB
PLC2
(sold separately)
FRONT LEFT - OUT1
FRONT RIGHT - OUT2
SPARE LEFT - OUT3
SPARE RIGHT - OUT4
REAR LEFT - OUT5
REAR RIGHT - OUT6
SUB LEFT - OUT7
SUB RIGHT - OUT8
LAPTOP
USB 2.0 Type B
USB SETUP / UPDATE PORT
USB 2.0 Micro-B 5-Pin
LED
EXPANSION PORT
Reserved For Future Use
VEHICLE PORT
Maestro T-Harness
INPUT LEVEL SWITCH
INPUT
(looking into wired end)
OUTPUT
(looking into wired end)
High => 4.1v RMS
Low <= 4.0v RMS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Black
Black
Black
Black
Black
Black
Black
Black
Red
White
Red
White
Red
White
Red
White
Right Sub (-)
Left Sub (-)
Right Rear (-)
Left Rear (-)
Right Spare (-)
Left Spare (-)
Right Front (-)
Left Front (-)
Right Sub (+)
Left Sub (+)
Right Rear (+)
Left Rear (+)
Right Spare (+)
Left Spare (+)
Right Front (+)
Left Front (+)
Pin Wire Function Pin Wire Function
16 15 14 13 12 11 10 9
8 7 6 5 4 3 2 1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Orange/Black
Violet/Black
Green/Black
Black
Black
Gray/Black
White/Black
Blue/White
Black
Orange
Violet
Green
Red
White
Gray
White
Blue
Yellow
SPDIF In (-)
Right Rear (-)
Left Rear (-)
Right Aux In Shield
Left Aux In Shield
Right Front (-)
Left Front (-)
Remote Output
Ground
SPDIF In (+)
Right Rear (+)
Left Rear (+)
Right Aux In (+)
Left Aux In (+)
Right Front (+)
Left Front (+)
Remote In
B+ Constant
Pin Wire Function Pin Wire Function
18 17 16 15 14 13 12 11 10
9 8 7 6 5 4 3 2 1
COLOR SOLID BLINKING
White Device On –
Blue BT/USB Connected BT/USB Activity
Red Memory/Device Error –
Yellow B+ Undervoltage (<9V) B+ Overvoltage (>16V)
Green – Maestro Activity
Violet Boot Loader Error –
Front
Full-Range
Rear
Full-Range
Rear
Subwoofers
Front
Mid-bass
DSR1 TYPICAL OUTPUT CONFIGURATION + PIN OUTS
Theall-in-onedigitalsoundprocessorandamplierreplacementinterface
allowsforinstallationofaftermarketampliersinvirtuallyanyvehicle.
illustrated by Eric Russell

Step 2 - Install the Weblink plugin (for PC only)
Gotoidatalinkmaestro.com/pluginandfollowthe
installationsteps.ReviewtheSystemRequirements
beforeinstalling.Macintosh not supported.
Step 3 - Register a Weblink account
Gotoidatalinkmaestro.com/registerandcompletethe
registrationprocess.Aconrmationemailwillbesentto
yourequiringvalidation.
Step 4 - Connect Maestro module to PC
UsetheincludedminiUSBcabletoconnectyourDSR1
moduletoyourPC.
Step 5 - Weblink Programming
Gotoidatalinkmaestro.com/login.Enteryour
usernameandpassword,thenclickOK.Followthe
installationstepsinWeblinkuntilyourmoduleisashed,
thendownloadyourinstallguide.
Step 6 - Complete Vehicle-Specific Installation
Followthestepsinyourinstallguideandcompletethe
installation.ADSrecommendshavingtheDSR1installed
byacertiedtechnician.Vehicle-specific T-harness
required and sold separately.
DSR1 MAESTRO PROGRAMMING & INSTALLATION
TheDSR1modulewillrequireweb-programmingasperthestepsbelow,
beforeinstallationaswellasavehicle-specicT-harnesssoldseparately.
877.212.6169
1230-61763-01-C
Step 1 - Update DSR1
PriortoMaestroprogramming,updatetheDSR1at
www.rockfordfosgate.com/products/details/dsr1
forthelatestaudiofeatures.