Rola 8 Series User manual

ALL DESIGN CONCEPTS ARE INTELLECTUAL PROPERTY OF ROLACASE AND ARE NOT TO BE COPIED, DISTRIBUTED OR COMMUNICATED TO UNAUTHORISED PARTIES
FOR TECHNICAL SUPPORT CALL: 1 [phone] / EMAIL: [email protected] / WEB: www.rolacase.com
Screw Drivers Cordless Drill with
Torque settings
RSSHL/
INSTALLATION MANUAL
RSSHL/ (RolaCase Shelves)
INCLUSIONS:
ATTENTION: PLEASE READ ALL INSTRUCTIONS BEFORE ASSEMBLING/INSTALLING THIS PRODUCT
ANY ALTERATIONS, UNINTENDED OR UNAPPROVED WORK/USE OF THIS PRODUCT COULD CREATE A
HAZARDOUS CONDITION THAT CAN CAUSE DEATH, PERSONAL INJURY OR PROPERTY DAMAGE.
BEFORE YOU BEGIN:
•THE AVERAGE EXPECTED INSTALL TIME FOR THIS PRODUCT IS 8 MINUTES
•READ ALL THE INSTRUCTIONS BEFORE ASSEMBLY & INSTALLATION
•ALWAYS WEAR APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT, ESPECIALLY
EYEWEAR WHEN INSTALLING OUR PRODUCTS
•CONFIRM YOU HAVE ALL THE NECESSARY PARTS, TOOLS, EQUIPMENT, & TIME
REQUIRED BEFORE COMMENCING
WARNING
PART No. RSSHL/ shelving range to suit the following
• All “8-Series” shelving bays (8 Series Start Frame- RSSFR/HD/80/1539 or 2006, (8 Series Exten-
sion Frame- RSEFR/HD/80/1539 or 2006) & “12-Series” shelving bays (12 Series Start Frame- RSSFR/
HD/120/1539 or 2006, 12 Series Extension Frame- RSEFR/HD/120/1539 or 2006) (sold separately), this
is where you will find screws and plastic plugs to fit the shelves
TOOLS AND HARDWARE REQUIRED:
ATTENTION
IMAGES USED IN THIS GUIDE MAY VARY SLIGHTLY DEPENDING ON YOUR MODEL
The following RolaCase shelves are designed to fit the 8-SERIES RolaCase shelving bays
that are constructed out of one or both of the following part #’s: 8 Series Start Frame
- RSSFR/HD/80/1539 or 2006 Or 8 Series Extension Frame - RSEFR/HD/80/1539 or
2006
(sold separately)
8 Series Shelving Range (33”wide)
IMAGE MAY VARY BASED ON YOUR SHELF MODEL
RSSHL/85
RSSHL/86
RSSHL/89
The following RolaCase shelves are designed to fit the 12-SERIES RolaCase shelving bays
that are constructed out of one or both of the following part #’s: 12 Series Start Frame-
RSSFR/HD/120/1539 or 2006 or 12 Series Extension Frame - RSEFR/HD/120/1539 or
2006 (sold separately)
12 Series Shelving Range (49.6”wide)
RSSHL/125
RSSHL/126
RSSHL/129
All RolaShelf shelving products are to be used exclusively and in conjunction with
RolaCase and RolaShelf shelving bays only. Failure to do so will cause the shelving/
products to perform in a nonfunctional manner and will void your warranty
ATTENTION
33”
33”
33”
12”
16”
16”
3.5”
3.5”
6.6”
1.8”
3.1”
3.1”
50”
12”
3.5”
1.8”
50”
16”
6.6”
50”
16”
3.5”
3.1”
3.1”
Screws* Plastic plugs*
(optional)
*included in our Start and Extension Frames

ALL DESIGN CONCEPTS ARE INTELLECTUAL PROPERTY OF ROLACASE AND ARE NOT TO BE COPIED, DISTRIBUTED OR COMMUNICATED TO UNAUTHORISED PARTIES
FOR TECHNICAL SUPPORT CALL: 1 [phone] / EMAIL: [email protected] / WEB: www.rolacase.com
INSTALLATION MANUAL
RSSHL/ (RolaCase Shelves)
ATTENTION: PLEASE READ ALL INSTRUCTIONS BEFORE ASSEMBLING/INSTALLING THIS PRODUCT
ANY ALTERATIONS, UNINTENDED OR UNAPPROVED WORK/USE OF THIS PRODUCT COULD CREATE A
HAZARDOUS CONDITION THAT CAN CAUSE DEATH, PERSONAL INJURY OR PROPERTY DAMAGE.
WARNING ATTENTION
IMAGES USED IN THIS GUIDE MAY VARY SLIGHTLY DEPENDING ON YOUR MODEL
The RolaCase shelves are secured to the assembled shelving bays with the use of
“Phillips Head Dog Point Screws” which are supplied with the purchase of any shelving
bay type
(sold separately)
A Begin by locating the shelf and carefully sliding it in between a compatible
shelving bay frame.
Note that 8-Series shelves will only fit into 8-Series shelving bays, and 12-Series
shelves will only fit into 12-Series shelving bays (all sold separately)
B Trial position the shelf in an ideal position anywhere on the perforated shelving
frame (please note: the frame should be installed in the vehicle first) whilst
ensuring the grid pattern on the shelf ends marries up with the holes on the twin
posts. Note that RolaCase’s shelves are very versatile within the shelving bays and can
be secured in many different varying positions
C If you wish, you can use the disposable plastic plugs that come in our ‘Starter’
and ‘Extension’ frames
(sold separately) to hold your shelf in place while deciding
where to secure it
D Secure the selected shelf to the frame posts using a “P3” Phillips Head screwdriver
or a cordless drill with a low torque setting and the screws. Please ensure you do not
over tighten these screws as it is unnecessary and it may also strip the thread. De-
pending on the type of shelf you are securing, you may be using either 4 or 6 screws
per side, refer to image below:
D Secure other side of the shelf
E Repeat this process for any other shelf you are installing and then once you
are done, go through and double check that all screws are tight before placing any
products or tools on the shelves
Secure all
matching
shelving and
post holes
Example of
shelving fitted
on bay
REV 1.5.2
For further details please go
to www.rolacase.com
Example of shelving fitted in
a Ford Transit
*Frame not
included