Roll-X GO Series User manual

ROLL-X GO
ROLL-X GO INSTALLATION MANUAL -
HALF ASSEMBLED 2018.01

1
Installaon manual ROLL-X GO-
PARTS
ROLL-X 327 / 175 GO |
ROLL-X 400 / 175 GO |
ROLL-X 470 / 175 GO |

2
TABLE OF CONTENT Page
SET THE TABLE HEIGHT 3 - 4
ASSEMBLY - LOWER FRAME CONSTRUCTION 5 - 8 and 11,16
ASSEMBLY - COMPRESSOR 9 - 10
ASSEMBLY - FLATBED 12 - 12
ASSEMBLY - ILLUMINATION 13 - 14 and 19
ASSEMBLY - GLIDE BEAM 15 - 15 and 17
ASSEMBLY - GAS DAMPER TILT FUNCTION 18 - 18
ASSEMBLY - ACRYLIC 19 - 20
ASSEMBLY - GLASS 20 - 21
ASSEMBLY - CUTTING MAT 22 - 22
CONNECT - GLIDE BEAM 23 - 23
USE TILT FUNCTION 24 - 25
OVERVIEW CONTROL PANEL 26 - 26
ASSEMBLY - ROLL HOLDER, GLIDE BEAM 26 - 26

3
1.1 Start by removing the side bracket plates. 2 plates on each side of the leg.
(6 pcs M8x16 hex cap screws and 6 pcs M8 locking nuts)
1.2 Remove the leg bracket plates (front and back).
(8 pcs M8x16 hex cap screws and 8 pcs M8 locking nuts)
SET THE TABLE HEIGHT

4
1.3 Set the height by bolng the leg bracket plates
(front and back) to the required height
(8 pcs M8x16 Hex Cap screws and 8 pcs M8 locking nuts)
Mount the side bracket plates.
(6 pcs M8x16 hex cap screws and 6 pcs M8 locking nuts)
NOTE! Do not mount the leg bracket plates (front and back) lower than the
leg supports placed on the sides of the leg)
1.4 NOTE: Do not place the leg bracket plates (front and back)
higher than the last two holes of the leg construcon.
SET THE TABLE HEIGHT

5
2.1 Mount the lower frame beams
(16 pcs M8x16 Hex cap screw and 16 pcs M8 locking nuts)
2.0 Place the leg pair with the leg lid facing each other.
ASSEMBLY - LOWER FRAME CONSTRUCTION

6
2.2 Mount the middle support bracket with the connectors pre - mounted to.
(4 pcs M8x16 Hex cap screw and 4 pcs M8 locking nuts)
NOTE! For a ROLL-X 470 / 175 GO - Mount 3 middle support bracket, the bracket with connectors pre
mounted to shall be installed in the middle of the table as picture.
2.3 Mount the air lter. Make sure to mount the air lter facing the concave side of the middle support bracket.
(2 pcs M5x18 Hex screws and 2 pcs M5 locking nuts)
ASSEMBLY - LOWER FRAME CONSTRUCTION

7
2.4 Place the rst table console on the same side as the air lter. NOTE! If you have purchased
with lt funcon, make sure that the rst console has the plasc knob and sprint on the right side.
2.5 Lock the rst table console in place
(6 pcs M8x16 Hex cap screws and 6 pcs M8 locking nuts)
ASSEMBLY - LOWER FRAME CONSTRUCTION

8
2.6 Pull the air hose from the air lter through the holes in the leg bracket plate (front and back).
Connect the air hose to the air pressure regulator.
2.7 Sck the cable holders to the lower frame beam according to picture.
Clean the surface with an alcohol based detergent)
ASSEMBLY - LOWER FRAME CONSTRUCTION

9
2.8 Mount the compressor shelf.
(4pcs M6x12 Hex screw and 4pcs M6 Locking nuts)
2.9 Place the compressor on top of the compressor shel, no screws needed.
MOUNT THE COMPRESSOR