Ronda 200H User manual

USER MANUAL
(Original) (Country code EU ; CH ; DK )
RONDAâ200H
RONDAâ200H-S
Handy Industrial Vacuum Cleaner for Fine Dust and
Dust Hazardous to Health
IMPORTANT!
Read this manual
before you start using the vacuum cleaner.
V. BRØNDUM A/S

User Manual
RONDA
â
200H (RONDA
â
200H-S) 3 V. BRØNDUM A/S

User Manual
RONDA
â
200H (RONDA
â
200H-S) 4 V. BRØNDUM A/S
Table of Contents
GENERAL DESCRIPTION ..................................................................................................................................................6
SAFETY PRECAUTIONS.....................................................................................................................................................7
Guidelines in Connection with Disposal of the Machine............................................................................................................8
GENERAL SAFETY INSTRUCTIONS ..........................................................................................................................................9
TECHNICAL DATA............................................................................................................................................................11
STANDARD ACCESSORIES .............................................................................................................................................12
APPLICATIONS ..................................................................................................................................................................13
DESCRIPTION OF THE MAIN PARTS...........................................................................................................................14
MOTOR TOP WITH SUCTION MOTOR AND HEPA FILTER ...............................................................................................14
MOTOR TOP WITH ALARM AND PRESSURE RELIEF VALVE .............................................................................................14
COLLECTION CONTAINER WITH MULTI-TUBE FILTER ....................................................................................................15
COLLECTION CONTAINER AND FILTER BAG.....................................................................................................................15
MODE OF OPERATION ....................................................................................................................................................16
ASSEMBLING......................................................................................................................................................................17
COLLECTION OF DRY DUST..........................................................................................................................................18
ELECTRICAL OUTLET WITH AUTOMATIC START/STOP ...................................................................................................18
CLEANING OF THE MULTI-TUBE FILTER DURING OPERATION (AS NEEDED OR WHEN THE ALARM BEEPS)...................20
EMPTYING ..........................................................................................................................................................................21
REORDERING OF FILTER BAGS..........................................................................................................................................22
DUST HAZARDOUS TO HEALTH AND ASBESTOS.................................................................................................................22
CLEANING AND MAINTENANCE..................................................................................................................................23
MAINTENANCE OF THE MOTOR TOP ........................................................................................................................23
CHANGE OF FILTERS ......................................................................................................................................................24
INGENERAL .......................................................................................................................................................................24
Disposal of Used Filters......................................................................................................................................................26
TROUBLESHOOTING .......................................................................................................................................................27
DECLARATION OF CONFORMITY...............................................................................................................................28
SERVICE AND REPAIR.....................................................................................................................................................29

User Manual
RONDA
â
200H (RONDA
â
200H-S) 5 V. BRØNDUM A/S

User Manual
RONDA
â
200H (RONDA
â
200H-S) 6 V. BRØNDUM A/S
RONDAâ200H and 200H-S
Industrial Vacuum Cleaner for Fine Dust and
Dust Hazardous to Health
General Description
Congratulations on your new RONDAâ200H / RONDAâ200H-S industrial vacuum cleaner
from V. BRØNDUM A/S.
RONDAâ200H / RONDAâ200H-S is an industrial vacuum cleaner developed for the collection of very fine and
health hazardous dust. RONDAâ200H / RONDAâ200H-S meets the requirements for vacuum cleaners within
the industry and the construction industry today. The machine is ideal for the collection of fine and health
hazardous dust, such as cement or dust from grinding machines. The machine is ideal for use in connection with
hand tools.
·Self-cleaning Teflon-coated multi-tube filter (BIA dust class ”M”)
·Filter cleaning during operation with back flush valve
·HEPA-filter (BIA/IFA dust class ”H”)
·Protection level IPX4 (IEC 60 529)
·Satisfies the demands of EN 60 335-2-69 Annex AA, for collection of health
hazardous dust in dust class ”H”
·Electrical outlet with automatic start/stop
·Beeper alarm in case of too low air flow
·Soft start of motor
·Post-suction when using hand tool
RONDAâ200H-S is mounted with separate exhaust coupling. It is relatively easy to
mount separate exhaust coupling on RONDAâ200H, if this is required.
It is, however, necessary to send the motor top to V.Brøndum A/S - or the dealer - for alteration.
The machine cannot immediately be restored to the original RONDAâ200H without exhaust coupling.
Read this manual before you operate the machine.
Keep the manual readily accessible to all users.

User Manual
RONDA
â
200H (RONDA
â
200H-S) 7 V. BRØNDUM A/S
The user manual is to ensure a secure operation of the vacuum cleaner, and to secure that the user is in no way
uncertain as to the use. The manual must be stored near the vacuum cleaner.
Does any uncertainty arise as to the use of the vacuum cleaner or the material collected, the work should be
stopped until all questions have been cleared.
Pictures and drawings are for illustrative purpose and will make the understanding of the manual easier. The
pictures shown may therefore be different from the actual product.
Safety Precautions
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
·The appliance is NOT approved for collection of flammable, explosive, poisonous or extremely health
hazardous dust, fluids or gasses.
·DO NOT USE THE VACUUM CLEANER WITHOUT A PROPER GROUND CONNECTION. This vacuum
cleaner is designed to be used with a grounding connection, in an installation with HFI or HPFI. The user is
responsible for ensuring that the wall outlet is grounded. The ground connection of the plug must NOT be
removed.
·RONDAâ200H / RONDAâ200H-S must be connected to 230 V power supply. Make sure that the voltage
and safety fuse of the power supply correspond with the data of the data plate and the information given in
this manual.
·RONDAâ200H / RONDAâ200H-S may be used for collection of dust hazardous to health according to
CEI/IEC 60335-2-69 Annex AA, dust class H.
·The appliance must be emptied after use.
·The user must ensure that the appliance is adjusted to the task and that regulatory requirements are met.
·When collecting dust hazardous to health you must use a filter bag, and disposal must comply with the legal
requirements for material (closed container, plastic bag etc.).
·Avoid damaging the supply cord. When replacing the supply cord, only use an original supply cord (see the
spare parts list). V. BRØNDUM A/S, an authorized V. BRØNDUM A/S dealer or an equally qualified person
must carry out the replacement in order to avoid danger. Regularly check the mains connection for damage,
such as fissures or ageing. If damage is found, the supply cord must be replaced before further use.
·The plug must be removed from the power supply before repair and maintenance operations.
·The mains socket of the machine is to be used only for the purposes specified in the user manual.
·This machine is intended for commercial use, e.g. in hotels, schools, hospitals, factories, shops, offices and
rental businesses.
·Before use operators should be provided with information, instruction and training for the use of the
appliance and the substances for which it is to be used, including the safe method of removal and disposal
of the material collected.
·For user servicing, the appliance must be dismantled, cleaned and serviced, as far as is reasonably
practicable, without causing risk to the maintenance staff and others. Suitable precautions include

User Manual
RONDA
â
200H (RONDA
â
200H-S) 8 V. BRØNDUM A/S
decontamination before dismantling, provision for local filtered exhaust ventilation where the appliance is
dismantled, cleaning of the maintenance area and suitable personal protection.
·In the case of class H appliances the outside of the appliance should be decontaminated by vacuum
cleaning methods and wiped clean or treated with sealant before being taken out of a hazardous area. All
the appliance parts shall be regarded as contaminated when removed from the hazardous area and
appropriate action taken to prevent dust dispersal.
·The manufacturer, or an instructed person, shall perform a technical inspection at least annually, consisting
of, for example, inspection of filters for damage, air tightness of the appliance and proper function of the
control mechanism. On class H appliances the appliance filtration efficiency should be tested at least
annually, or more often, according to national requirements. The test method that may be used for the
verification of the appliance filtration efficiency is given in AA.22.201.2. If the test will not be passed, it must
be repeated with a new essential filter.
·When carrying out service or repair operations, all contaminated items, which cannot be satisfactorily
cleaned, are to be disposed of. Such items shall be disposed of in impervious bags in accordance with any
current regulation of the disposal of such waste.
·The upper part of the motor top is a non-dust proof compartment, and when cleaning, the covers of this
compartment are removed by loosening the screws fixing the covers.
·IMPORTANT! The vacuum cleaner must not be started with covers removed.
·When the automatic start/stop is activated in connection with electrical hand tools, you must
ALWAYS turn off the hand tools before you turn off the machine.
·IMPORTANT! The motor top must not be covered when the vacuum cleaner is in use.
Guidelines in Connection with Disposal of the Machine
Does the safe use or maintenance of the appliance raise any questions, do not hesitate to contact either your
dealer or V. BRØNDUM A/S.
The product you have purchased is subject to Directive 2002/96/EC of the European
Parliament and the Council of the European Union on waste electrical and electronic
equipment (WEEE) and should not be disposed of as unsorted municipal waste. Please
utilize your local WEEE collection facilities in the disposition of this product and otherwise
observe all applicable national requirements.

User Manual
RONDA
â
200H (RONDA
â
200H-S) 9 V. BRØNDUM A/S
General Safety Instructions
1. Keep the working area clean. Slippery and greasy surfaces increase the risk of accidents.
2. Be aware of the surroundings. Do not expose the vacuum cleaner to rain. Do not use the vacuum
cleaner in moist or wet surroundings. Do not use the vacuum cleaner near flammable gasses or
liquids.
3. Protect against electrical shock.
Avoid bodily contact with earthed building parts, such as radiator, water pipes and the like and
also electrical appliances with their own earth connection.
4. Keep children and unauthorized persons away from the workplace.
Do not let unauthorized persons touch the vacuum cleaner or the supply cord. All unauthorized
persons should be kept at a distance.
5. Put the vacuum cleaner away, or make it ready for transport after use.
Keep the vacuum cleaner in a dry place and inaccessible to children.
6. Do not use force.
Do not use force when operating the vacuum cleaner. Do not step on the hose, or the electrical
cord.
7. Choose the correct tool, accessories for the task.
Do not use badly proportioned or light tools for heavy tasks. Do not use tools for anything they are
not intended for.
8. Choose suitable working clothes.
9. Personal protective equipment.
Put on eye and/or ear protection, if necessary. Put on respirator in dusty environments.
10. Protect the electrical cord.
Never carry the vacuum cleaner in the electrical cord. Do not remove the plug from the socket by
pulling the electrical cord. Keep the electrical cord away from heating sources, oil and sharp
edges.
11. Choose a safe working position so that there will be no risk of falling in the hose and cord.
12. Keep the machine and equipment in good repair.
Keep the vacuum cleaner clean and dry and follow the instructions of the chapter about
When using electrical equipment the necessary safety precautions must
be taken in order to avoid
the risk of fire, electrical shock and damage to
persons. The below safety instructions are to be read and followed when
the vacuum cleaner is being used.

User Manual
RONDA
â
200H (RONDA
â
200H-S) 10 V. BRØNDUM A/S
maintenance.
13. Cut off the electricity supply when the vacuum cleaner is not in use.
Remove the plug from the socket before maintenance, repair and when the vacuum cleaner is not
in use.
14. If extension cords are used out of doors, they must be approved for this. If extension cords are
used, the following guidelines must be observed.
15. Show attention and be rested.
The vacuum cleaner must not be used, if the user is tired, sleepy or sick or under the influence of
alcohol or drugs / medicine.
16. Check for damage.
Check the vacuum cleaner for damage. Check that the shields etc. have been properly fastened.
Check the electrical switches, and have an authorized service mechanic replace them, if they are
damaged. Do not use the vacuum cleaner, if it cannot be started and/or stopped at the switch.
RONDAâ200H / RONDAâ200H-S is H-classified in accordance with the demands of EN 60335-2-69 Annex AA
for collection of dust hazardous to health.
RONDAâ200H /RONDAâ200H-S is furthermore in accordance with the Machinery Directive (2006/42/EC).
3 labels are enclosed. One in Danish, one in English and one in French.
The standard language of the label on the machine is German. Therefore the label with the language of the
country in question is to be placed on the H-label, with the text as shown above.
Length of cord in
metres
Cross section
<16A
<25A
Up to 20 m
Ø1,5mm²
Ø2,5mm²
20-50 m
Ø2,5mm²
Ø4,0mm²
WARNING: This appliance contains dust hazardous to
health.
Emptying and maintenance operations, including
removal of the dust collecting means, must only be
carried out by authorized personnel wearing suitable
personal protection. Operate only after the full filtration
system has been fitted and checked.
H
H

User Manual
RONDA
â
200H (RONDA
â
200H-S) 11 V. BRØNDUM A/S
Make sure that the voltage and fuse of the power
supply correspond with the data of the dat
a plate of the
machine and the data of this manual.
Technical Data
RONDAâ200H / RONDAâ200H-S is
connected to 230 V power supply.
The survey below shows the technical data of RONDAâ200H & RONDAâ200H-S
A169
EU
CH
DK
Voltage
Suction motor
Power outlet, max.
Vacuum
Air volume, max.
*Suction power, max. ((P2)based on IEC 60312
)
Filter area, multi-tube filter
Filter area, HEPA
Collection capacity (bag / container)
Height
Length
Width
Weight without accessories
Container coupling
Length of supply cable
Noise
Based on ISO 11201
Machine pressure level : uncertainty K
pA=3dB
(Measured only as machine)
Based on EN 60704
-1:2010 and EN60704-2-1:2001
Max. Sound
Power Level LWA=
uncertainty KWA=3dB
(Measured with hose,
pipes and floor accessory)
230
1100
2000
2550
25
54
194
345
0.8
1.1
14/16
795
430
450
15
Ø 50
8
<70
<85
230
1100
1200
2550
25
54
194
345
0.8
1.1
14/16
795
430
450
15
Ø 5
0
8
<70
<85
230
1100
1800
2550
25
54
194
345
0.8
1.1
14/16
795
430
450
15
Ø 50
8
<70
<85
Volt
Watt
Watt
mmWc
kPa
l/
sec.
m3
/h
W
m
2
m²
l
mm
mm
mm
kg
mm
m
dB(A)
dB
*Data of the machine with 4 metres ø 38 hose
In connection with extraction from tools (dust extractor) it is
necessary to ensure a sufficient rate of air renewal (L) in the
room.
According to the instructions from The Danish Working
Environment Service,
recirculation of extracted air is forbidden.
Please refer to national regulations.

User Manual
RONDA
â
200H (RONDA
â
200H-S) 12 V. BRØNDUM A/S
Standard Accessories
RONDAâ200H / RONDAâ200H-S is delivered with a complete set of accessories including tubes, hose and all
the necessary nozzles.
You can reorder the accessories using the following product numbers:
1. 40 mm professional’s set .......................................................... 80.33.4037
2. Plastic hose, 4 m.......................................................................... 84.54.3809
3. Crevice nozzle.............................................................................. 80.34.4000
4. Round brush................................................................................. 80.34.4001
5. Floor nozzle B-370 ....................................................................... 84.38.3620
6. Tubes, two straight ones and one curved .................................... 80.52.2160
7. Pyramid shaped cuff (with hose and coupling)............................. 81.56.3810
2
7
1
2
3
4
6
5
7

User Manual
RONDA
â
200H (RONDA
â
200H-S) 13 V. BRØNDUM A/S
Applications
RONDAâ200H / RONDAâ200H-S is a vacuum cleaner in accordance with DS/EN 60335-2-2 and CEI/IEC
60335-2-69 Annex AA class H and may only be used as such.
RONDAâ200H / RONDAâ200H-S may be used for collection of dust hazardous to health according to CEI/IEC
60335-2-69 Annex AA dust class H.
RONDAâ200H / RONDAâ200H-S may not be used for collection of fluids or moist dust.
RONDAâ200H / RONDAâ200H-S may not be used for collection of flammable, explosive, poisonous or other
dust, fluids or gasses hazardous to health.
RONDAâ200H / RONDAâ200H-S may only be used in dry environments and may not be used or stored
outdoors or indoors under wet conditions.
The capacity of a vacuum cleaner to suck vacuum depends on the air. Theoretical the suction capacity will fall
when the vacuum cleaner is used at altitudes. The suction capacity of the vacuum cleaner will be constant from 0
to approx. 800 m above sea level. From 800 to 2000 m the suction capacity will theoretically fall to approx. 75%.
It is not recommended to use the vacuum cleaner at more than 2000 m above sea level, as the cooling and the
suction capacity will be considerably reduced.

User Manual
RONDA
â
200H (RONDA
â
200H-S) 14 V. BRØNDUM A/S
Description of the Main Parts
RONDAâ200H / RONDAâ200H-S is designed as a handy and compact industrial vacuum cleaner for collection
of fine dust and dust hazardous to health.
Motor Top with Suction Motor and HEPA Filter
The motor top is equipped with suction motor, an integrated handle, switches for the
suction motor and the built-in automatic start-/stop.
The powerful suction motor of RONDAâ200H / RONDAâ200H-S is placed in the
motor top.
The motor top is fitted with a HEPA filter in dust class ”H”.
The filter holds back the fine and smallest dust particles, which have not been held
back by the multi-tube filter. The filter holds back the particles larger than 0.3 mm
(0.0003 mm). The surface of the filter is 1.1 m2and is protected by a metal grating.
Motor Top with Alarm and Pressure Relief Valve
The motor top is equipped with a pressure relief valve and will beep for alarm when
the air flow is too low (<20 m/sec).
The motor top can be equipped with a separate exhaust coupling. I.e. the air will be
exhausted through a hose coupling in the motor top. It will then be necessary to
use a hose.
Electrical hand tools can be connected directly to the RONDAâ200H /
RONDAâ200H-S.

User Manual
RONDA
â
200H (RONDA
â
200H-S) 15 V. BRØNDUM A/S
Collection Container with Multi-Tube Filter
The large multi-tube filter of the RONDAâ200H / RONDA®200H-S is mounted
directly in the collection container.
The surface of the filter of 8000 cm2is coated with Teflon. The Teflon coating
repels the dust, which will in this way not stick so easily to the filter material.
The multi-tube filter has a self-cleaning effect during operation.
The filter consists of a large number of tubes mounted on springs. During
operation the tubes vibrate a little, and a part of the dust sucked on to the
surface of the filter will fall down into the collection container.
Collection Container and Filter Bag
The collection container is equipped with 5 swivel wheels.
The collection container contains the filter bag where the material is collected, which facilitates the emptying and
disposal of the material collected.
The material can also be collected directly into the collection container.
Furthermore you can use a filter bag for dust-free emptying.
The filter bag cannot be filled up when very fine dust is collected.
When collecting dust hazardous to health you must pay attention to the
requirements as to disposal of the collected material. (Closed container; plastic
bag or container). The demands as to packing of the material collected may vary.

User Manual
RONDA
â
200H (RONDA
â
200H-S) 16 V. BRØNDUM A/S
Mode of Operation
When the suction motor of the machine is on, the air will be led through the machine and will collect the dust
particles near the nozzle mounted.
The dust particles will be sucked through the hose into the collection container, where the majority of the particles
will be held back in the filter bag and/or the multi-tube filter.
The air flow and the remaining particles, which have not fallen to the bottom of the collection container or have
been held back in the filter bag or the multi-tube filter, will be carried forward to the HEPA filter.
From the HEPA filter the purified air flow will continue through the suction pump (blow through) and will be led out
of the vacuum cleaner through the exhaust and noise reduction filters.
IMPORTANT! As the motor leads the cooling air through the machine,
all filters MUST be mounted and intact.
IMPORTANT! Never cover up the motor top when the machine is in use.
IMPORTANT! Never collect warm or glowing materials.
IMPORTANT! Never extract from processes producing sparks.

User Manual
RONDA
â
200H (RONDA
â
200H-S) 17 V. BRØNDUM A/S
Assembling
·Check that the packing is intact and has no sign of damage from handling and transport.
·Unpack RONDAâ200H / RONDAâ200H-S and check that all the parts ordered are there.
·Assemble the three parts of the tube and mount
an appropriate nozzle.
·Fasten the rubber coupling of the suction hose to the tube and mount the other end of the hose in the
coupling of the container of RONDAâ200H / RONDAâ200H-S.
·Check that the collection container is empty and that the multi-tube filter has been correctly mounted in
the collection container. Check that the filters of the machine are intact and undamaged (see the chapter
“Change of Filters”).
·If dust hazardous to health is to be collected you must use a collection / filter bag.
·Before the plug is connected to the electrical main supply you must make sure that the plug and the cord
are undamaged. If the cord or the plug is damaged, a professional must replace the parts. Only an
original cord may be mounted.
·Connect the machine to 230 V power supply with a reliable earth connection.
·Remember to place the label onto the H-label, if the language of the user is not German.
·RONDAâ200H / RONDAâ200H-S is now ready for use. The collection is described in details in the
following chapter.

User Manual
RONDA
â
200H (RONDA
â
200H-S) 18 V. BRØNDUM A/S
NOTE:
If hand tool with a power consumption of more than
1100 W
is connected, the total current consumption will exceed
approx. 10 A, which is often the normal fuse size.
Collection of Dry Dust
When the machine has been correctly assembled and connected, it can be switched on and off at the red
start/stop switch of the motor top. The machine has been equipped with an alarm indicating when the air flow is
too low for collection. This alarm has to be checked before use.
Block the intake at the end of the hose, and the machine will start beeping.
Unblock, and the beeper alarm will stop.
During operation the RONDAâ200 can be driven around on the 5 swivel
wheels mounted on the collection container.
The floor nozzle is perfect for collection of dust and materials from large flat
surfaces. The nozzle is provided with brushes
and wheels to ensure an optimal positioning
of the nozzle on the flat surface.
Gradually the brushes will be worn, and the
nozzle will no longer collect in the optimum
way. Adjust the height of the wheels using the
knob on the nozzle so that the brushes only
just touch the floor.
Electrical Outlet with Automatic Start/Stop
RONDAâ200H / RONDAâ200H-S is equipped with an automatic start/stop and electrical outlet. If you connect
electrical hand tools directly to the power outlet of the motor top, the RONDAâ200 will automatically be switched
on and off when the hand tools are switched on and off.
Therefore the suction will continue for some seconds after the hand tools has been
switched off before the machine will stop.
The electrical hand tool is connected to the electrical outlet at the rear of the motor top.
RONDAâ200H / RONDAâ200H-S can be used with hand tools with a power
consumption of:
Country code EU 2000W
Country code CH 1200W
Country code DK 1800W
1800 W corresponds to a current consumption of approx. 13A.
Information can be found on the data
plate

User Manual
RONDA
â
200H (RONDA
â
200H-S) 19 V. BRØNDUM A/S
The automatic start/stop is activated with the black switch on the
motor top. When the automatic start/stop is activated, the machine
will not start when you push the red switch. The machine will not start
until the hand tool connected is started.
Set the red switch on “I”to put on the vacuum cleaner.
Automatic start/stop “I”= the automatic start/stop is activated. The vacuum cleaner will start when you use the
hand tool.
Automatic start/stop “O”= the automatic start/stop is not activated. The vacuum cleaner will start when you set
the main switch (red) on “I”.
When the automatic start/stop is activated “1” and hand tool is connected to the electrical outlet, the machine will
start when the hand tool is started.
ALWAYS TURN OFF the hand tool before you turn off the machine on the switch.
Separate extraction (RONDA 200H-S)
If the machine is equipped with a separate exhaust coupling, a hose must
be used for the air exhausted.
WARNING:
If no hose is used, the air exhausted may raise dust from the floor, and
there may also be a risk of dust exposure.
The hoses are available in varying lengths. It is recommended not to use
hoses longer than 10 metres.

User Manual
RONDA
â
200H (RONDA
â
200H-S) 20 V. BRØNDUM A/S
Cleaning of the Multi-Tube Filter during Operation (as needed or when the alarm beeps)
Block the intake / hose so that full vacuum is made in the machine.
Repeat the steps 1-3 approx. 2-3 times when cleaning.
The difference in pressure / the shock effect will clean the surface of the filter, when air is drawn through the
valve in order to suppress the negative pressure in the collection container and the hose, and will reject possible
deposits from the multi-tube filter.
The pressure release valve will close. This method gives an effective cleaning of the multi-tube filter.
It is recommended always to leave the machine for a few minutes before emptying it, if the machine is being used
without filter bag. The dust will fall to the bottom of the container, and the risk of swirling dust into the
surroundings during the emptying is reduced.
NOTE: Do not ”tap” on the intake as this will swirl up the dust in the container and result in blocking of the multi-
tube filter. Therefore ALWAYS use the shock valve for cleaning of the multi-tube filter during operation.
Block the intake /
Block the hose.
Take hold of the flap of the
shock valve.
Pull the flap of the shock valve
while the machine is blocked
and running. (Do not tug the
valve)
When the power grows bigger
than the influence from the
vacuum, the valve will
automatically open with a
”puff”. Let go of the valve.

User Manual
RONDA
â
200H (RONDA
â
200H-S) 21 V. BRØNDUM A/S
Emptying
The RONDAâ200H / RONDAâ200H-S can collect the material, depending on the character of the material,
directly in the collection container or in a filter bag (if collecting dust hazardous to health a filter bag must be
used). If the machine has been used without filter bag immediately before the emptying, it is recommended to
wait a few minutes with the emptying to allow the fine dust to fall to the bottom of the collection container.
·Loosen the four container clips attaching the motor top to the collection container and remove the motor
top.
·Place the motor top on a dry and clean surface.
·Carefully lift up the multi-tube filter in the two handles.
·Carefully place the multi-tube filter on a dry, flat surface.
If no filter bag has been used, the collection container can now be emptied.
·If a filter bag has been used, the bag is removed from the container coupling.
·Close the filter bag.
·Now you can dispose of the filter bag.
REMEMBER: Disposal of dust hazardous to health must take place in accordance with the national regulations.
·Put a new filter bag in the collection container.
·Put the multi-tube filter and the motor top in place.
A filter bag must be used when collecting dust hazardous to health.
·Place the collar of the filter bag on the container coupling.
·Filter bags containing dust hazardous to health must always be closed and disposed of in accordance
with the national regulations.
REMEMBER: Always empty the machine after use.
You must make sure that the dust and material collected cannot fall out of the machine during transport.