ROSE DISPLAYS ANOGOTCHA STAND TELESCOPING User manual

11” round base
vertical post
ball knobs
top AnoGotcha holder
bottom
AnoGotcha holder
AnoGotcha
Shells 11” round bases
AnoGotcha™Stand
Instruction Sheet
T-Gotchas
Here are all the parts required to assemble 1 Telescoping AnoGotcha Stand.
Parts
AnoGotcha is a trademark of Rose Displays, Ltd. Neither the manufacturer nor any
sales agent may be held liable for injury, loss or damage resulting from the use of these products.
Part #02INSTeleAnoGotchaStand
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[email protected]
Finished look.
Read this instruction sheet carefully
before assembly. Separate all parts and
check quantities. Make sure all parts
are accounted for before discarding
any packaging materials.
If you experience any problems with
the assembly, please call Rose Displays
at 1-800-631-9707, ext. 5510 vertical poles
with telescoping
locks
ball knobs &
threaded rods shaped end caps
Important terms:
telescoping locks
Telescoping
#97-0500

Screw ball knobs onto threaded rods.
Step 1
AnoGotcha™Standassembly continued
•Locate four ball knobs and
two threaded rods.
•Screw one ball knob
onto one end of each
threaded rod.
Note:
Do not screw a ball
knob onto both ends
of threaded rods.
AnoGotcha is a trademark of Rose Displays, Ltd. Neither the manufacturer nor any
sales agent may be held liable for injury, loss or damage resulting from the use of these products.
Part #02INSTeleAnoGotchaStand
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[email protected]
Screw vertical poles into 11” round bases.
Step 2
Incept-12.09.02
•Screw the end of one
vertical pole onto the
threaded stud of each
11” round base.
• Repeat for both poles.
Screw ball knob on one end of
threaded rod and tighten. You should now have one ball knob on one end of each threaded rod.
Screw one vertical pole onto each
11” round base. Tighten with hands.
You should have two matching vertical poles with bases.
vertical
pole
11” round
base
Telescoping

Insert T-Gotcha holders into AnoGotcha shells.
Step 3
• Slide one T-Gotcha holder
into each AnoGotcha shell.
•Attach one shaped end
cap onto each end of both
AnoGotcha shells.
AnoGotcha is a trademark of Rose Displays, Ltd. Neither the manufacturer nor any
sales agent may be held liable for injury, loss or damage resulting from the use of these products.
Part #02INSTeleAnoGotchaStand
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[email protected]
Attach top AnoGotcha holder onto vertical poles.
Step 4
Incept-12.09.02
•Slide one threaded rod with
ball knob through top hole
in one vertical pole.
• Slide threaded rod
completely through top
channel of one AnoGotcha
holder and through top hole
of second vertical pole.
• Screw second ball knob
onto other end of threaded
rod. Tighten securely.
Slide T-Gotcha holder into each
AnoGotcha shell as shown. Attach one shaped end cap onto each end of AnoGotcha holders,
as shown.
You should now have two AnoGotcha holders with
one shaped end cap on each end.
Slide threaded rod through the
top hole of one vertical pole and
then through top channel of one
AnoGotcha holder.
Slide threaded rod through top hole
in second vertical pole. Screw ball
knob tightly onto threaded rod. Your stand should now look like this.
T-Gotcha
shaped
end cap
vertical
pole
top
AnoGotcha
holder
11” round
base
ball knobs
AnoGotcha
shell
AnoGotcha™Standassembly continued
Telescoping

Attach bottom AnoGotcha holder to vertical poles.
Step 5
AnoGotcha is a trademark of Rose Displays, Ltd. Neither the manufacturer nor any
sales agent may be held liable for injury, loss or damage resulting from the use of these products.
Part #02INSTeleAnoGotchaStand
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[email protected]
Incept-12.09.02
Slide threaded rod through
appropriate hole and through
bottom channel of remaining
AnoGotcha holder.
Slide threaded rod through matching
hole on opposite vertical pole. Attach ball knob, tighten securely.
Be sure locks are facing
same direction.
2”
14”
2”
8”
• Choose hole that matches
appropriate graphic distance
from floor.
• Slide one threaded rod
with ball knob through
appropriate hole in one
vertical pole and through
bottom channel of one
AnoGotcha holder.
• Slide through corresponding
hole of second vertical pole.
Note:
Make sure the hinge on the
bottom T-Gotcha faces up
and in the same direction as
the hinge on the T-Gotcha
at the top of the stand.
• Screw second ball knob
onto other end of threaded
rod. Tighten securely.
T-Gotcha hinge must face up and in the same direction as top T-Gotcha.
8”
14”
AnoGotcha™Standassembly continued
Telescoping
Numbers represent
distance from floor.

Close locks on both poles.Open locks on both poles.
Insert your graphic into Telescoping AnoGotcha Stand.
Step 6
AnoGotcha is a trademark of Rose Displays, Ltd. Neither the manufacturer nor any
sales agent may be held liable for injury, loss or damage resulting from the use of these products.
Part #02INSTeleAnoGotchaStand
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[email protected]
Open locks, raise top bar to tension graphic, snap locks closed.
Step 7
Incept-12.09.02
•Open locks on both poles.
•Raise top bar to
tension graphic.
• Snap locks closed.
Your AnoGotcha stand is now
complete and ready for display.
Your completed Telescoping AnoGotcha
Stand should look similar to this.
Insert graphic into top
AnoGotcha holder. Snap the holder shut. Snap the holder shut.Insert graphic into bottom
AnoGotcha holder.
Poster inserted into top AnoGotcha holder.Poster inserted into bottom AnoGotcha holder.
For each pole, place foot
on base and raise top bar
to tension graphic.
If you have any questions about your Telescoping AnoGotcha Stand assembly,
please call Rose Displays at 1-800-631-9707, ext. 5510 and we will assist you.
AnoGotcha™Standassembly continued
Telescoping
• Snap open top AnoGotcha
holder completely. Slide
graphic into holder until it
reaches inside top of
Gotcha. Snap AnoGotcha
holder shut. It is easiest to
close the holder by starting
at one end and working your
way to the other end.
• Repeat for bottom
AnoGotcha holder.