ROSE DISPLAYS ANOGOTCHA STAND WITH TOPPER User manual

9” round base
vertical post
ball knobs
top AnoGotcha holder
bottom AnoGotcha holder
AnoGotcha
Shell
12AT300
9” round base
97-0302
AnoGotcha™Stand with Topper Clips
Instruction Sheet
T-Gotcha
12GT100
These are all the parts required to assemble 1 AnoGotcha Stand.
Parts
AnoGotcha is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor any
sales agent may be held liable for injury, loss or damage resulting from the use of these products.
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
Finished look.
Read this instruction sheet care-
fully before assembly. Separate
all parts and check quantities.
Make sure all parts are account-
ed for before discarding any
packaging materials.
If you experience any problems
with the assembly, please call
Rose Displays at
1-800-631-9707.
vertical poles
97-0301 ball knobs & threaded rods
97-0303
97-0304
shaped
end caps
97-0305
Important terms:
Topper Clips
06-6100
Topper Clip

Screw ball knobs onto threaded rods.
Step 1
AnoGotcha™Stand assembly continued
•Locate four ball knobs and
two threaded rods.
•Screw one ball knob
onto one end of each
threaded rod.
Note:
Do not screw a ball
knob onto both ends
of threaded rods.
AnoGotcha is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor any
sales agent may be held liable for injury, loss or damage resulting from the use of these products.
Part #02INSAnoGotchaStandTopper
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[email protected]
Screw vertical poles onto 9” round bases.
Step 2
•Screw the end of one
vertical pole onto the
threaded stud of each
9” round base.
• Repeat for both poles.
Screw one ball knob on one end of
threaded rod and tighten. You should have one ball knob on one end of each threaded rod.
Screw one vertical pole onto each
9” round base. Tighten with hands.
You should have two matching vertical poles with bases.
vertical
pole
9” round
base

Insert T-Gotcha holders into AnoGotcha shells.
Step 3
AnoGotcha™Stand assembly continued
• Slide one T-Gotcha holder
into each AnoGotcha shell.
•Attach one shaped end
cap onto each end of both
AnoGotcha shells.
AnoGotcha is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor any
sales agent may be held liable for injury, loss or damage resulting from the use of these products.
Part #02INSAnoGotchaStandTopper
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[email protected]
Attach top AnoGotcha holder onto vertical poles.
Step 4
•Slide one threaded rod with
ball knob (created in step 1)
through top hole in one
vertical pole (created in
step 2).
• Slide threaded rod
completely through top
channel of one AnoGotcha
holder (created in step 3)
and through top hole of
second vertical pole.
• Screw second ball knob
onto other end of threaded
rod. Tighten securely.
Slide T-Gotcha holder into each
AnoGotcha shell as shown. Attach one shaped end cap onto each end of AnoGotcha holders,
as shown.
You should have two AnoGotcha holders with one
shaped end cap on each end.
Slide threaded rod through the
top hole of one vertical pole and
then through top channel of one
AnoGotcha holder.
Slide threaded rod through top hole
in second vertical pole. Screw ball
knob tightly onto threaded rod. Your stand should now look like this.
T-Gotcha
shaped
end cap
vertical
pole
top
AnoGotcha
holder
9” round
base
ball knobs
AnoGotcha
shell

Attach bottom AnoGotcha holder to vertical poles.
Step 5
AnoGotcha™Stand assembly continued
AnoGotcha is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor any
sales agent may be held liable for injury, loss or damage resulting from the use of these products.
Part #02INSAnoGotchaStandTopper
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[email protected]
Slide threaded rod through height
slot that matches the length of your
graphic and through bottom channel
of remaining AnoGotcha holder.
Slide threaded rod through matching
hole on opposite vertical pole. Attach ball knob, but do not tighten. Leave loose until
graphic is inserted.
Bottom AnoGotcha must be
attached at slot that matches
the length of your graphic.
60”
48”
28”
28”
60”
48”
•Choose the height slot
that matches the length
of your graphic.
•Slide one threaded rod with
ball knob (created in step 1)
through appropriate hole in
one vertical pole (created in
step 2) and through bottom
channel of one AnoGotcha
holder (created in step 3).
•Slide threaded rod through
corresponding slot of second
vertical pole.
Note:
Make sure the hinge on the
bottom T-Gotcha faces up
and in the same direction as
the hinge on the T-Gotcha
at the top of the stand.
• Loosely screw second
ball knob onto end of
threaded rod.
Note:
Ball knob must be kept loose
until graphic is inserted.
T-Gotcha hinge must face up and in the same direction as T-Gotcha on the top.

Turn ball knob in your right
hand away from you.
Hold both knobs and pull down
slightly to tension graphic.
Insert your graphic into AnoGotcha Stand.
Step 6
• Open top AnoGotcha
holder and insert top
edge of your graphic
until it reaches the
top of the holder.
Snap shut top holder.
• Open the bottom
AnoGotcha holder and
insert bottom edge of your
graphic until it reaches the
bottom of the holder. Snap
shut bottom holder.
AnoGotcha is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor any
sales agent may be held liable for injury, loss or damage resulting from the use of these products.
Part #02INSAnoGotchaStandTopper
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[email protected]
Tension poster and tighten bottom AnoGotcha holder.
Step 7
•Hold both ball knobs on
bottom AnoGotcha holder,
and pull down slightly,
to tighten and straighten
your graphic.
• Turn ball knobs in opposite
directions to secure bottom
AnoGotcha holder.
Your AnoGotcha stand is now
complete and ready for display.
Your completed AnoGotcha Stand
should look similar to this.
Insert graphic into top
AnoGotcha holder. Snap the holder shut. Snap the holder shut.Insert graphic into bottom
AnoGotcha holder.
Poster inserted into top AnoGotcha holder.Poster inserted into bottom AnoGotcha holder.
To tighten, turn ball knob in
your left hand towards you.
AnoGotcha™Stand assembly continued

Attach Topper Clips onto top rail of AnoGotcha.
Step 8
The AnoGotcha Stand is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor
any sales agent may be held liable for injury, loss or damage resulting from the use of these products.
Part #02INSAnoGotchaStandTopper
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[email protected]
• Push both Toppers Clips
onto top rail of AnoGotcha
holder and place one at
each end of rail.
• Insert poster into
Topper Clips.
Squeeze top tabs together to open
Topper Clip. While open, push
Topper Clip onto rail until it snaps
into place. Repeat for multiple
Topper Clips.
Insert graphic into top clip of Topper
Clip. Be sure to push graphic
completely into clip. Finished Look
AnoGotcha™Stand assembly continued
If you have any questions about your AnoGotcha Stand assembly, please call
Rose Displays at 1-800-631-9707 and we will assist you.