Rose electronics CNV-VGADVISC User manual

Translator
VGA To DVI Converter/Scaler
10707 Stancliff Road
Houston, Texas 77099
Phone [phone]
www.rose.com
INSTALLATION AND OPERATIONS
MANUAL

LIMITED WARRANTY
Copyright Rose Electronics 2015. All rights reserved.
No part of this manual may be reproduced, stored in a retrieval system, or transcribed in any form or any means, electronic or mechanical, including photocopying and
recording, without the prior written permission of Rose Electronics.
Rose Electronics Part # MAN-DVI_VGA_CNV_SCL
Printed In the United States of America - Revision 1.1
Rose Electronics
®
warrants the Rose Translator to be in good working order for one year from the date of
purchase from Rose Electronics or an authorized dealer. Should this product fail to be in good working order at
any time during this one-year warranty period, Rose Electronics will, at its option, repair or replace the Unit as
set forth below. Repair parts and replacement units will be either reconditioned or new. All replaced parts
become the property of Rose Electronics. This limited warranty does not include service to repair damage to
the Unit resulting from accident, disaster, abuse, or unauthorized modification of the Unit, including static
discharge and power surges.
Limited Warranty service may be obtained by delivering this unit during the one-year warranty period to Rose
Electronics or an authorized repair center providing a proof of purchase date. If this Unit is delivered by mail,
you agree to insure the Unit or assume the risk of loss or damage in transit, to prepay shipping charges to the
warranty service location, and to use the original shipping container or its equivalent. You must call for a return
authorization number first. Under no circumstances will a unit be accepted without a return authorization
number. Contact an authorized repair center or Rose Electronics for further information.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO A
PERIOD OF ONE YEAR FROM THE DATE OF PURCHASE, AND NO WARRANTIES, WHETHER EXPRESS
OR IMPLIED, WILL APPLY AFTER THIS PERIOD. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTIED ABOVE, YOUR SOLE
REMEDY SHALL BE REPLACEMENT OR REPAIR AS PROVIDED ABOVE. IN NO EVENT WILL ROSE
ELECTRONICS BE LIABLE TO YOU FOR ANY DAMAGES INCLUDING ANY LOST PROFITS, LOST
SAVINGS OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF OR
THE INABILITY TO USE SUCH PRODUCT, EVEN IF ROSE ELECTRONICS OR AN AUTHORIZED DEALER
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY ANY OTHER
PARTY.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, SO THE ABOVE MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH MAY VARY FROM STATE TO STATE.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Subpart J of Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
IBM, AT, and PS/2 are trademarks of International Business Machines Corp. Microsoft and Microsoft Windows
are registered trademarks of Microsoft Corp. Any other trademarks mentioned in this manual are
acknowledged to be the property of the trademark owner.

TABLE OF CONTENTS
Contents Page #
Disclaimer ......................................................................................................................................................... 1
System Introduction .......................................................................................................................................... 1
About this manual ............................................................................................................................................. 1
Features........................................................................................................................................................ 1
Package Contents......................................................................................................................................... 1
Rose Translator Models .................................................................................................................................... 2
Top View ....................................................................................................................................................... 2
Front View..................................................................................................................................................... 2
Rear View ..................................................................................................................................................... 2
Installation......................................................................................................................................................... 3
Rose Translator Operation ................................................................................................................................ 4
Rose Translator Menu System ...................................................................................................................... 4
Navigating the Menu System..................................................................................................................... 5
Output Setup Menu Item ........................................................................................................................... 7
Output Resolution.................................................................................................................................. 7
Picture Menu Item ..................................................................................................................................... 9
Contrast................................................................................................................................................. 9
Brightness ........................................................................................................................................... 10
Saturation............................................................................................................................................ 11
Hue...................................................................................................................................................... 12
Color Range ........................................................................................................................................ 13
Color Temperature .............................................................................................................................. 14
Color Balance...................................................................................................................................... 15
Edge Enhance..................................................................................................................................... 1
Sharpness ........................................................................................................................................... 17
Adjustment Menu Item............................................................................................................................. 18
Under scan / Over scan....................................................................................................................... 18
Aspect Ratio ........................................................................................................................................ 19
Horizontal Mirror .................................................................................................................................. 20
Vertical Mirror ...................................................................................................................................... 21
Horizontal Shift .................................................................................................................................... 22
Vertical Shift ........................................................................................................................................ 23
Phase .................................................................................................................................................. 24
System Menu Item................................................................................................................................... 25
OSD Timeout....................................................................................................................................... 25
Display Notify....................................................................................................................................... 2
Input Resolution Information................................................................................................................ 27
Firmware Version ................................................................................................................................ 28
Factory Reset ...................................................................................................................................... 29
Test Patterns Menu Item ......................................................................................................................... 30
Dip Switch Configuration ............................................................................................................................. 31
Safety.............................................................................................................................................................. 32
Maintenance and Repair ................................................................................................................................. 33
Technical Support ........................................................................................................................................... 33

Figures Page #
Figure 1. Rose Translator Top View .................................................................................................................. 2
Figure 2. Rose Translator Front View ................................................................................................................ 2
Figure 3. Rose Translator Rear View................................................................................................................. 2
Figure 4. Rose Translator Installation ................................................................................................................ 3
Figure 5. Menu Controls on the Rose Translator ............................................................................................... 4
Figure . Menu System Display......................................................................................................................... 4
Figure 7. Main Menu and Submenus................................................................................................................. 5
Figure 8. System Menu Item and Submenu....................................................................................................... 5
Figure 9. Submenu Item Selection..................................................................................................................... 5
Figure 10. Navigating the Submenu................................................................................................................... 5
Figure 11. Selected Submenu Item ...................................................................................................................
Figure 12. Menu System is Redisplayed after Submenu Item Selection ............................................................
Figure 13. Going Back to the Main Menu...........................................................................................................
Figure 14. Exiting the Menu System ..................................................................................................................
Figure 15. Output Setup Menu........................................................................................................................... 7
Figure 1 . Output Resolution Selection Box ...................................................................................................... 7
Figure 17. Current Resolution Display ............................................................................................................... 7
Figure 18. Output Resolution Selection Box With Final Selection ...................................................................... 7
Figure 19. Return to Output Setup Menu ........................................................................................................... 8
Figure 20. Picture Submenu with Contrast Highlighted...................................................................................... 9
Figure 21. Contrast Selection Box ..................................................................................................................... 9
Figure 22. Picture Submenu with Brightness Highlighted................................................................................. 10
Figure 23. Brightness Selection Box................................................................................................................ 10
Figure 24. Picture Submenu with Brightness Highlighted................................................................................. 11
Figure 25. Saturation Selection Box................................................................................................................. 11
Figure 2 . Picture Submenu with Hue Highlighted........................................................................................... 12
Figure 27. Hue Selection Box .......................................................................................................................... 12
Figure 28. Picture Submenu with Color Range Highlighted ............................................................................. 13
Figure 29. Color Range Selection Box............................................................................................................. 13
Figure 30. Picture Submenu with Color Temp. Highlighted.............................................................................. 14
Figure 31. Color Temp. Selection Box ............................................................................................................. 14
Figure 32. Picture Submenu with Color Balance. Highlighted .......................................................................... 15
Figure 33. Color Balance. Select Color Selection Box ..................................................................................... 15
Figure 34. Set Color Balance for Selected Color Selection Box ....................................................................... 15
Figure 35. Picture Submenu with Edge Enhance. Highlighted ......................................................................... 1
Figure 3 . Edge Enhance Selection Box ......................................................................................................... 1
Figure 37. Picture Submenu with Sharpness Highlighted ................................................................................ 17
Figure 38. Sharpness Selection Box................................................................................................................ 17
Figure 39. Adjustment Submenu with Under/Over Scan Highlighted ............................................................... 18
Figure 40.Under/Over Scan Selection Box ...................................................................................................... 18
Figure 41. Adjustment Submenu with Aspect Ratio Highlighted....................................................................... 19
Figure 42. Aspect Ratio Selection Box............................................................................................................. 19
Figure 43. Adjustment Submenu with H-Mirror Highlighted.............................................................................. 20
Figure 44. Horizontal Mirror Selection Box....................................................................................................... 20
Figure 45. Horizontal Mirror for an Image ........................................................................................................ 20
Figure 4 . Adjustment Submenu with V-Mirror Highlighted.............................................................................. 21
Figure 47. Vertical Mirror Selection Box........................................................................................................... 21
Figure 48. Vertical Mirror for an Image ............................................................................................................ 21
Figure 49. Adjustment Submenu with H-Shift Highlighted................................................................................ 22
Figure 50. Horizontal Shift Selection Box......................................................................................................... 22
Figure 51. Adjustment Submenu with V-Shift Highlighted ................................................................................ 23
Figure 52. Vertical Shift Selection Box............................................................................................................. 23
Figure 53. Adjustment Submenu with Phase Highlighted................................................................................. 24
Figure 54. Phase Selection Box....................................................................................................................... 24
Figure 55. System Submenu with OSD Timeout Highlighted ........................................................................... 25
Figure 5 . OSD Timeout Selection Box ........................................................................................................... 25
Figure 57. System Submenu with Display Notify Highlighted........................................................................... 2

Figure 58. Display Notify Selection Box........................................................................................................... 2
Figure 59. System Submenu with Input Res. Info Highlighted ......................................................................... 27
Figure 0. Input Res. Info Display Box ............................................................................................................ 27
Figure 1. System Submenu with F/W Version Highlighted............................................................................. 28
Figure 2. F/W Version Display Box................................................................................................................ 28
Figure 3. System Submenu with Factory Reset Highlighted .......................................................................... 29
Figure 4. Factory Reset Selection Box .......................................................................................................... 29
Figure 5.Test Patterns Submenu with White Highlighted............................................................................... 30
Figure . Available Test Patterns on the Video Converter and Scaler ........................................................... 30
Figure 7. Dip Switch on the Video Converter and .Scaler.............................................................................. 31
Figure 8. Output Setup Submenu System ..................................................................................................... 35
Figure 9. Picture Submenu System............................................................................................................... 3
Figure 70. Adjustment Submenu System ........................................................................................................ 37
Figure 71. System Submenu System .............................................................................................................. 38
Figure 72. Test Patterns Submenu System..................................................................................................... 39
Figure 73. Exit Submenu System .................................................................................................................... 39
Figure 74. Mounting the Rose Translator ........................................................................................................ 41
Tables Page #
Table 1. Dip Switch Configuration ................................................................................................................... 31
Table 2.Rose Translator Specifications ........................................................................................................... 34
Table 3. Default Menu Settings ....................................................................................................................... 40
A endices Page #
Appendix A- Specifications.............................................................................................................................. 34
Appendix B- Menu System Summary.............................................................................................................. 35
Output Setup Menu ..................................................................................................................................... 35
Picture Menu............................................................................................................................................... 3
Adjustment Menu ........................................................................................................................................ 37
System Menu .............................................................................................................................................. 38
Test Patterns Menu ..................................................................................................................................... 39
Exit Menu System ....................................................................................................................................... 39
Appendix C – Default Settings......................................................................................................................... 40
Appendix D- Surface Mounting Instructions..................................................................................................... 41

INTRODUCTION
Rose Translator Installation and O eration Manual 1
Disclaimer
While every precaution has been taken in the preparation of this manual, the manufacturer assumes no
responsibility for errors or omissions. Neither does the manufacturer assume any liability for damages resulting
from the use of the information contained herein. The manufacturer reserves the right to change the
specifications, functions, circuitry of the product, and manual content at any time without notice.
The manufacturer cannot accept liability for damages due to misuse of the product or other circumstances
outside the manufacturer’s control. The manufacturer will not be responsible for any loss, damage, or injury
arising directly or indirectly from the use of this product. (See limited warranty.)
System Introduction
Thank you for choosing the Rose Translator (VGA to DVI Converter/Scaler). The Rose Translator is the result
of Rose Electronics commitment to providing state-of-the-art solutions for today’s demanding workplace. The
unit allows locations with legacy computers to streamline their operations by converting the video to utilize
newer higher-resolution monitors.
The Rose Translator is designed to connect analog graphic cards to DVI compliant digital monitors.
Computers, laptops, or other VGA sources with HD15 video connectors can be connected to a DVI video
display using the VGA to DVI Converter/Scaler. The video can be scaled up to 1080p Full HD and 1920 x 1200
(WUXGA). An intuitive and comprehensive on-screen display (OSD) menu allows easy set-up and control.
Wide power supply operating range of V to 24V DC offers installation flexibility for mobile use, in complex
studio systems with a common power supply, and with remotely located power sources. A locking power
supply connector, small footprint, and a surface-mountable enclosure facilitate easy and secure installation.
About this manual
This manual covers the installation and operation of the Rose Translator. The Installation Section describes
how to connect the unit. The Operation section describes the OSD menus, and the functionality of the dip
switch.
Features


 Converts and scales VGA to DVI


 Input resolutions up to 1920 x 1200 (WUXGA)


 Output resolutions up to 1080p 0, 2048 x 1080, and 1920 x 1200 (WUXGA)


 On-screen display (OSD) menu allows easy set-up and control


 Aspect Ratio Control: Source, 1 :9, 4:3 and Stretch


 Test Pattern Generator for quick system configuration


 Wide power supply operating range ( V to 24V DC)


 Locking power supply connector


 Surface mountable
Package Contents
The ackage contents consist of the following:
The Rose Translator Unit as ordered
1 x ft. VGA cable (M-M)
1 x 12V Power Supply
Manual
Additional cables are usually ordered separately. If the package contents are not correct, contact Rose
Electronics or your reseller so the problem can be quickly resolved.

MODELS
2 Rose Translator Installation and O eration Manual
Rose Translator Models
The Rose Translator comes in a single model as shown below.
To View
Figure 1. Rose Translator Top View
Front View
Figure 2. Rose Translator Front View
Buttons / Connectors:
1. DVI OUT: Use a DVI cable to connect a DVI
display to this port.
2. ▲, ▼, MENU: These push buttons are used to
change settings within the on-screen menu
system. See the Rose Translator Menu
System section on page 4 for more
information.
Rear View
Figure . Rose Translator Rear View
Connectors / Indicators:
1. VGA IN: Connect included VGA cable from
source device (e.g. computer) to this port
2. USB: This mini-USB port is reserved for use
by Rose Electronics.
. 12V DC: Connect included 12V DC power
supply to this power receptacle.
4. PWR: Under normal operating conditions, this
LED indicator will glow bright blue.

INSTALLATION
Rose Translator Installation and O eration Manual 3
Installation
Installation of the Rose Translator is very simple. The steps to do so are outlined below.
1. Connect the included VGA cable from the video source (e.g. a computer) to the VGA IN port on the
unit.
2. Connect a DVI cable from the DVI OUT port to a DVI display.
3. Connect the included power supply to the 12V DC power receptacle on the unit, and connect the power
unit to an available electrical outlet.
The completed installation will appear as in the figure below.
Figure 4. Rose Translator Installation

OPERATION
4 Rose Translator Installation and O eration Manual
Rose Translator O eration
This section deals primarily with the menu system of the Rose Translator and the functionality it provides. In
addition, the function of the unit’s dip switch is discussed here
Rose Translator Menu System
The Rose Translator uses a built-in menu system to manage and control all video features. To display the
menu system, press the MENU button on the front panel.
Figure 5. Menu Controls on the Rose Translator
The menu system will be displayed in the upper-left corner of the screen, as shown in the figure below.
Figure 6. Menu System Display
If the menu system is not used within the time interval specified by the OSD Timeout setting, the menu system
will be automatically closed. By default, the OSD Timeout setting is 5 seconds. See the OSD Timeout section
on page 25 for instructions on setting the OSD Timeout value.

Rose Translator Installation and O eration Manual 5
Navigating the Menu System
The main menu contains six menu items: Output Setup, Picture, Adjustment, System, Test Patterns and Exit.
The currently selected menu item in the main menu will always be highlighted in yellow.
Each menu item within the main menu, with the exception of Exit, contains a submenu. The submenu for a
menu item is displayed automatically when the menu item is selected.
Figure 7. Main Menu and Submenus
Use the ▲ or ▼ button on the front panel to highlight the desired item within the main menu. For example, if
the ▼ button is pressed three times, the System menu item is highlighted, and its submenu displayed.
Figure 8. System Menu Item and Submenu
To access the submenu for the highlighted menu item in the main menu, press the MENU button a second
time. When a submenu is activated, a green bar is used to indicate the current selection.
Figure 9. Submenu Item Selection
Use the ▲ or ▼ button to navigate through the submenu.
Figure 10. Navigating the Submenu
Current Selection
Submenu
Main Menu
Current
Selection

Rose Translator Installation and O eration Manual
Select the highlighted submenu item by pressing the MENU button. For example, if the MENU button is
pressed when the Input Res. Info submenu item is highlighted, the menu system is cleared from the screen,
and the following will be displayed.
Figure 11. Selected Submenu Item
Press the MENU button to return to the menu system.
Figure 12. Menu System is Redisplayed after Submenu Item Selection
To exit the submenu and return to the main menu, use the ▲ or ▼ button to highlight the <- Back submenu
item.
Figure 1 . Going Back to the Main Menu
To exit the menu system, use the ▲ or ▼ button to highlight the Exit option and press the MENU button.
Figure 14. Exiting the Menu System

Rose Translator Installation and O eration Manual 7
Output Setup Menu Item
The Output Setup menu item has just one item in its submenu. This is the Output Resolu. submenu item.
Out ut Resolution
Warning: Prior to changing this setting, ensure that the connected display can support the selected output
resolution. If an unsu orted resolution is selected, the unit will need to be reset using the di switch
on the bottom of the unit. See the Dip Switch Configuration section on page 31 for more information.
1. Press the MENU button on the front panel of the unit. The Output Setup menu item will be highlighted.
Figure 15. Output Setup Menu
2. Press the MENU button to access the Output Setup submenu. The Output Resolu. submenu item will be
highlighted.
3. Press the MENU button to select the Output Resolu. submenu item.
4. The Output Resolu. selection box will be displayed.
Figure 16. Output Resolution Selection Box
5. Use the ▲ or ▼ button to select the desired resolution. For a list of available output resolutions that are
supported by the Rose Translator, see Appendix B- Menu System Summary on page 35.
. After the desired output resolution is selected, press the MENU button to confirm the change.
7. When the output resolution has changed, the current input and output resolutions will be displayed above
the Output Resolu. selection box.
Figure 17. Current Resolution Display
Note: The input / output resolution display will only be displayed if Display Notify is set to On. See the
Display Notify section on page 2 for more information.
8. After a few seconds the Current Resolution Display will be removed.
9. The Output Resolu. selection box will still be displayed.
Figure 18. Output Resolution Selection Box With Final Selection

8 Rose Translator Installation and O eration Manual
10. Press the MENU button to return to the Output Setup menu.
Figure 19. Return to Output Setup Menu
11. Use the ▲ or ▼ button to select the <- Back submenu item.
12. Press the MENU button.
13. Use the ▲ or ▼ button to select the Exit menu item.
14. Press the MENU button to exit the main menu.

Rose Translator Installation and O eration Manual 9
Picture Menu Item
The Picture menu item provides several options to set the attributes of the displayed picture. These are
described below.
Contrast
1. Press the MENU button on the front panel of the unit. The Output Setup menu item will be highlighted.
2. Use the ▲ or ▼ button to highlight the Picture menu item.
3. Press the MENU button to display the Picture submenu. The Contrast submenu item will be highlighted.
Figure 20. Picture Submenu with Contrast Highlighted
4. Press the MENU button to select the Contrast submenu item.
5. The Contrast selection box will be displayed.
Figure 21. Contrast Selection Box
. Use the ▲ or ▼ button to set the desired contrast level.
7. Press the MENU button to confirm the change and return to the Picture submenu.
8. Use the ▲ or ▼ button to select the <- Back submenu item.
9. Press the MENU button.
10. Use the ▲ or ▼ button to select the Exit menu item.
11. Press the MENU button to exit the main menu.

10 Rose Translator Installation and O eration Manual
Brightness
1. Press the MENU button on the front panel of the unit. The Output Setup menu item will be highlighted.
2. Use the ▲ or ▼ button to highlight the Picture menu item.
3. Press the MENU button to display the Picture submenu. The Contrast submenu item will be highlighted.
4. Use the ▲ or ▼ button to highlight the Brightness submenu item.
Figure 22. Picture Submenu with Brightness Highlighted
5. Press the MENU button to select the Brightness submenu item.
. The Brightness selection box will be displayed.
Figure 2 . Brightness Selection Box
7. Use the ▲ or ▼ button to set the desired brightness level.
8. Press the MENU button to confirm the change and return to the Picture submenu.
9. Use the ▲ or ▼ button to select the <- Back submenu item.
10. Press the MENU button.
11. Use the ▲ or ▼ button to select the Exit menu item.
12. Press the MENU button to exit the main menu.

Rose Translator Installation and O eration Manual 11
Saturation
1. Press the MENU button on the front panel of the unit. The Output Setup menu item will be highlighted.
2. Use the ▲ or ▼ button to highlight the Picture menu item.
3. Press the MENU button to display the Picture submenu. The Contrast submenu item will be highlighted.
4. Use the ▲ or ▼ button to highlight the Saturation submenu item.
Figure 24. Picture Submenu with Brightness Highlighted
5. Press the MENU button to select the Saturation submenu item.
. The Saturation selection box will be displayed.
Figure 25. Saturation Selection Box
7. Use the ▲ or ▼ button to set the desired saturation level.
8. Press the MENU button to confirm the change and return to the Picture submenu.
9. Use the ▲ or ▼ button to select the <- Back submenu item.
10. Press the MENU button.
11. Use the ▲ or ▼ button to select the Exit menu item.
12. Press the MENU button to exit the main menu.

12 Rose Translator Installation and O eration Manual
Hue
1. Press the MENU button on the front panel of the unit. The Output Setup menu item will be highlighted.
2. Use the ▲ or ▼ button to highlight the Picture menu item.
3. Press the MENU button to display the Picture submenu. The Contrast submenu item will be highlighted.
4. Use the ▲ or ▼ button to highlight the Hue submenu item.
Figure 26. Picture Submenu with Hue Highlighted
5. Press the MENU button to select the Hue submenu item.
. The Hue selection box will be displayed.
Figure 27. Hue Selection Box
7. Use the ▲ or ▼ button to set the desired hue.
8. Press the MENU button to confirm the change and return to the Picture submenu.
9. Use the ▲ or ▼ button to select the <- Back submenu item.
10. Press the MENU button.
11. Use the ▲ or ▼ button to select the Exit menu item.
12. Press the MENU button to exit the main menu.

Rose Translator Installation and O eration Manual 13
Color Range
1. Press the MENU button on the front panel of the unit. The Output Setup menu item will be highlighted.
2. Use the ▲ or ▼ button to highlight the Picture menu item.
3. Press the MENU button to display the Picture submenu. The Contrast submenu item will be highlighted.
4. Use the ▲ or ▼ button to highlight the Color Range submenu item.
Figure 28. Picture Submenu with Color Range Highlighted
5. Press the MENU button to select the Color Range submenu item.
. The Color Range selection box will be displayed.
Figure 29. Color Range Selection Box
7. Use the ▲ or ▼ button to select between Limited and Full.
8. Press the MENU button to confirm the change and return to the Picture submenu.
9. Use the ▲ or ▼ button to select the <- Back submenu item.
10. Press the MENU button.
11. Use the ▲ or ▼ button to select the Exit menu item.
12. Press the MENU button to exit the main menu.

14 Rose Translator Installation and O eration Manual
Color Tem erature
1. Press the MENU button on the front panel of the unit. The Output Setup menu item will be highlighted.
2. Use the ▲ or ▼ button to highlight the Picture menu item.
3. Press the MENU button to display the Picture submenu. The Contrast submenu item will be highlighted.
4. Use the ▲ or ▼ button to highlight the Color Temp. submenu item.
Figure 0. Picture Submenu with Color Temp. Highlighted
5. Press the MENU button to select the Color Temp. submenu item.
. The Color Temp. selection box will be displayed.
Figure 1. Color Temp. Selection Box
7. Use the ▲ or ▼ button to select between Neutral, Cool and Warm.
8. Press the MENU button to confirm the change and return to the Picture submenu.
9. Use the ▲ or ▼ button to select the <- Back submenu item.
10. Press the MENU button.
11. Use the ▲ or ▼ button to select the Exit menu item.
12. Press the MENU button to exit the main menu.