ROSITEK MPP2 Operating instructions

CONTACT
Rositek Technologies E-mail: sup[email protected] © 2021 Rositek
www.rositek.com All rights reserved
BRICK PRESS
MANUAL & 2- IN-1 PRESSER
USER GUIDE AND TROUBLESHOOTING
MODEL No: MPP2 & PPM4

PAGE 1
USER GUIDE AND TROUBLESHOOTING
Rositek Technologies
www.rositek.com
© 2021 Rositek
All rights reserved
Email: sup[email protected]
PAGE 2 POLLEN BRICK PRESS OVERVIEW
PAGE 3 SAFETY PRECAUTIONS
PAGE 3 HANDLING PRECAUTIONS
PAGE 4 UNPACKING
Unpacking Precautions
Unpacking Instructions
Item Checklist -- MPP2 & PPM4
Recommended Parts
PAGE 5 GETTING FAMILIAR -- MPP2
PAGE 8 - 12 OPERATING INSTRUCTIONS
PAGE 13 TROUBLESHOOTING
How to Replace the Bottle Jack
Bottle Jack does not Hold Pressure After Receiving It, How to Fix It
How to Replace PID Module
PAGE 14 WARRANTY
TABLE OF CONTENTS
PAGE 6
PAGE 7
GETTING FAMILIAR -- PPM4
GETTING FAMILIAR -- Pollen Brick Mold
Disclaimer
Loading Materials
Pressing with MPP2 Manual Presser
Pressing with PPM4 2- IN -1 Presser
1# Step for Creating Birck
2# Step for Pressing Material
Cleaning Press Plates
PID Control Instructions for PPM4
PID Default Parameters for PPM4
How to Set Back to Default Settings

PAGE 2
Rositek Technologies
www.rositek.com
© 2021 Rositek
All rights reserved
Email: sup[email protected]
USER GUIDE AND TROUBLESHOOTING
POLLEN BRICK PRESS OVERVIEW
Rositek develops two kinds of brick press, Manual and Bottle Jack type, to meet the different
needs of the customers.
This unit is intended for LEGAL use only, in accordance with your
federal, state, and local laws, ordinances, and regulations.
DISCLAIMER
Picture
Model
No.
Type
Platen
Size
Power
( w )
Voltage
( v )
MPP2
Manual
N/M
N/M
N/M
PPM4
2- IN- 1
4-Ton Heat
Press
3 x 5”
500
110

PAGE 3
Rositek Technologies
www.rositek.com
© 2021 Rositek
All rights reserved
Email: sup[email protected]
USER GUIDE AND TROUBLESHOOTING
The following precautions are provided to prevent harm or injury to yourself and others.Please make
sure to thoroughly read, understand, and follow these precautions before using. After reading and
familiarizing yourself with the equipment, store the manual in a safe place for future references.
• Use this product only as described in this manual.
• Keep the equipment out of the reach of children at all times.
• Unplug the heat press from the electrical outlet and let it cool down
COMPLETELY before cleaning, performing maintenance, or repair.
• DO NOT operate the product after the appliance malfunctions or is dropped or
damaged in any way.
• Clean the plates with isopropyl alcohol and wipe them dry with a clean cloth.
Ensure both plates are completely dry before use.
• DO NOT leave any cords near a heat source.
• DO NOT handle a power plug or other components of the press with wet hands.
• DO NOT connect too many power plugs to the same power outlet.
• Remove dust around the plug and power cord with a clean dry cloth.
• DO NOT disassemble the press or make any modifications to the equipment
without professional instructions.
WARNING: Follow the warnings below.
SAFETY PRECAUTIONS
HANDLING PRECAUTIONS
• The press must be operated on a hard, level surface, away from its edges to
prevent accidental tipping over.
• Always attach the power cord to the press first, then plug it into the wall outlet.
• To unplug the press, turn OFF the power switch, only then remove the plug from
the outlet.
• DO NOT touch the press’s hot surfaces. Use heat-resistant gloves or tools.
• Keep your hands and other body parts away from the moving parts to
prevent injury.
• This press comes with a power cord that fits into a standard household 3-
prong outlet (110V American market and 220V European market).
• DO NOT attempt to use the equipment with a two-prong electrical cord or
any other way without proper grounding.
• DO NOT exceed the rated capacity.
• Always turn the machine OFF and unplug it when done using.

PAGE 4
Rositek Technologies
www.rositek.com
© 2021 Rositek
All rights reserved
Email: sup[email protected]
USER GUIDE AND TROUBLESHOOTING
UNPACKING
INSTRUCTIONS
1. Place the box on a large, sturdy, flat surface.
2. Open the box and remove the instruction manual and all parts that came
with the press.
3. Remove the packaging materials and carefully lift the device out of the box.
4. Examine the device after unpacking for any damage. If found one, take a
picture and contact Rositek at suppor[email protected]om immediately.
UNPACKING
UNPACKING
PRECAUTIONS
Keep the packaging materials (foam, plastic bags,etc.)
It is designed to protect the product and should be used in case you need to
return the device for repair or warranty maintenance in the future.
DO NOT attempt to ship the device in different packaging materials.
Before starting, please make sure that the following items are included
inside the machine. If anything is missing, contact ROSITEK support.
ITEM
CHECKLIST
1. 1pc x Aluminum Frame.
2. 1set x Pollen Brick Mold.
3. 2pc x Lever Handle.
4. 1pc x User Guide.
5. 1pc x Tools bag.
1. Parchment paper sheets.
2. Filter bags.
3. Collection tools.
RECOMMENDED
PARTS
The following items are recommended to successfully press and pre-serve the
optimal yield:
MPP2
Manual Presser
1. 1pc x Heat Press.
2. 1set x Pollen Brick Mold.
3. 1pc x Jack Handle.
4. 1pc x Power Cord.
5. 1pc x User Guide.
6. 1pc x Tools bag.
7. 1pc x Silicone Mat.
PPM4
2-IN-1 Presser

PAGE 5
Rositek Technologies
www.rositek.com
© 2021 Rositek
All rights reserved
Email: sup[email protected]
USER GUIDE AND TROUBLESHOOTING
GETTING FAMILIAR -- MPP2
MPP2
FEATURES
Pollen Brick Mold
Lever Handle 2
Frame
Lever Handle 1
Insert Handles in Holes
Tips: Select the corresponding
hole according to different
directions to increase the
pressure.
MPP2
PRODUCT SIZE
Front View Size (mm)Left view size(mm)
Thread Rod

PAGE 6
Rositek Technologies
www.rositek.com
© 2021 Rositek
All rights reserved
Email: sup[email protected]
USER GUIDE AND TROUBLESHOOTING
GETTING FAMILIAR -- PPM4
PPM4
FEATURES
Pollen Brick Mold
Press Handle
Pluggable Dual PID
Temp Controller
Jack Handle
Release Valve Knob
4-ton Bottle Jack
Top Platen
Bottom Platen
Bamboo Insulator
Jack Handle
Socket
Bamboo Insulator
PPM4
PRODUCT SIZE
Front View Size (mm) Left view size(mm)

PAGE 7
Rositek Technologies
www.rositek.com
© 2021 Rositek
All rights reserved
Email: sup[email protected]
USER GUIDE AND TROUBLESHOOTING
GETTING FAMILIAR -- POLLEN BRICK MOLD
Pollen Brick Mold
FEATURES
Ram of Mold
Pollen Brick Mold
PRODUCT SIZE
Front View Size (mm) Left view size(mm)
Housing
Base
Parchment Paper
(Not Included)

PAGE 8
Rositek Technologies
www.rositek.com
© 2021 Rositek
All rights reserved
Email: sup[email protected]
USER GUIDE AND TROUBLESHOOTING
Loading
Materials
1. Prepare materials you wish to make.
2. Take out the mold ram, and separate the housing and base.
3. Put a piece of parchment paper through the U-shape grooves on both ends
of the base.
4. To align the U-shaped grooves at both ends of the housing with the base
and push it inward until it is stuck so that the base will not fall off.
5. To load materials into the mold, press it down. Flatten it out on the top after
full to make sure the material is distributed evenly.
6. Put the second parchment paper on the top.
7. Set up the ram of mold.
OPERATING INSTRUCTIONS
Tips: The recommended size of parchment paper is width 126mm and length larger than 80mm to
prevent it from sticking.
Pressing
with MPP2
Manual Presser
1. After loading material inside of the pollen mold.
2. Push the mold in-between the base of press and the threaded rod of the
press and make sure it installs completely.
3. Rotate the lever handles clockwise, and you can select the corresponding
hole according to different directions to increase the pressure, until no more
pressure can be applied.
4. Rotate the lever handles counterclockwise to get the mold out of the
machine.
Tips: Capable of Being Heated - The
mold made of 6061 aluminum always
transfers and retains heat to melt the
materials, so you can pre-heat the mold
or materials before loading complete or
heat up the mold with hot water/another
method after loading the materials.

PAGE 9
Rositek Technologies
www.rositek.com
© 2021 Rositek
All rights reserved
Email: sup[email protected]
USER GUIDE AND TROUBLESHOOTING
Pressing
with PPM4
2 -IN -1 Presser
1. Insert the included power cord into the power cord socket and then plug the
other end into an electrical outlet.
2. Turn the knob clockwise until it is firmly closed to seal the release valve.
3. Flip the ON / OFF switch to turn the press on. The PID temp controller and
the power switch both become lit.
4. Press the PID control panels to set the desired temperature (About how to
set the temperature, please refer to Page 11) .
5. Wait until the platens heat up to the desired temperature.
6. Align the side without two corners on the bottom with the bottom plate, push
it inward to the end.The plate and the mold are exactly flush.Pay attention to
the directions of the bottom of the mold’s base.
7. Pump the jack handle until you can no longer pressure applied.
8. Turn the valve knob counterclockwise to release the press and lower the
bottom platen.
9. Remove the press mold using heat resistant gloves or tools.
10.Take out the brick. If get stuck, you can use a small rubber hammer or
wooden stick to hit the two corners on the bottom of the mold.
11. Turn the machine off by flipping ON / OFF switch when done pressing.
12.Unplug and then disconnect the power cord from the press.
13. Wait until the press cools down completely to clean and store it.
Step for
Creating Birck
Two corners
OPERATING INSTRUCTIONS (continued)