Weber CF 2-II Hd Operating instructions

CF 2-II Hd 1
CF 2-II Hd
Honda GX 160
0100220-00
Operating and
Maintenance Manual
0619/englisch/Übersetzung der Original-Betriebsanleitungl
Weber Maschinentechnik GmbH
Im Boden 5– 8, 10
D-57334 Bad Laasphe-Rückershausen/Germany
Tel.: [phone] / 398 0
Fax: [phone] / 398 101
E-mail: [email protected]
Web: www.webermt.de

2 CF 2-II Hd

CF 2-II Hd 3
Table of contents
Introduction 4
Safety guidelines 5
Graphic presentation 8
Device description 9
Technical data 10
Activities prior to starting work 12
Starting 14
Compacting 15
Shutting down 15
Maintenance overview 16
Maintenance work 17
Operating uids and ll levels 19
Troubleshooting 19
Storage 20
Contact addresses 23

4 CF 2-II Hd
Introduction
This operating and maintenance manual is designed to facilitate familiarization with your soil compactor,
and to enable you to maintain the compactor and use it for its intended purpose.
When complying with the instructions in the operating and maintenance manual you help avoid
hazards, reduce repair and downtime costs, and increase the reliability and service life of your soil
compactor.
This operating and maintenance manual must always be available at the implementation site of the
soil compactor.
If necessary, you can obtain additional information from your authorized WEBER MT dealer, or you
can obtain information from one of the contact addresses on the last page.
You can obtain information on the assembled Honda gasoline engine and nd a spare-part list for it
at www.honda-engines-eu.com
The valid conformity declaration is enclosed with every machine delivery.

CF 2-II Hd 5
Hearing protection
Hard hat
Safety shoes
Protective gloves
Safety guidelines
General
All safety instructions must be read and complied with, as non-compliance will result in
– danger to life and limb of the user,
– impairments to the machine or other property.
In addition to the operating manual, the accident-prevention regulations in the country where
the appliance is used must be complied with.
Intended use
The soil compactor should only be used if it is in a technically faultless condition, as intended,
in a safety-conscious and hazard-conscious manner, in compliance with the instructions in
the operating manual. Malfunctions that impair safety must be eliminated without delay.
The CF 2-II Hd soil compactor is designed exclusively for compacting
– sand,
– gravel,
– asphalt, crushed rock,
– low-cohesive mixed material,
– concrete paving stone.
Any other use of the soil compactor is considered to be improper use for which the owner shall be
exclusively responsible. All liability is rejected if damage occurs due to non-compliance with this
provision. This risk is borne solely by the user.
Easily foreseeable misuse
Any use for which the machine is not intended.
Operation
Soil compactors are only permitted to be operated by suitable persons of or above the age of 18.
Personnel must be instructed in how to guide the compactor by the owner or by the owner’s assigned
personnel.
The machine operator must comply with trafc regulations. If instructions that affect safety are given
by third parties, then the operator must be authorized to reject these instructions.
Unauthorized persons are not allowed in the area of the soil compactor during the compacting
process.
Protective equipment
This machine is capable of exceeding the permissible sound level of 80 dB(A). The owner might also
face additional dangers when using the machine. Precautionary action must, therefore, be taken.
Protective equipment includes:

6 CF 2-II Hd
The soil compactor described in this operating manual is suitable for use in trenches that are
deeper than shoulder height, provided the following basic conditions have been met:
– trench width at least 1.5 m
– trench depth no more than 3.0 m
– open trench width at least 10 m
– slight wind movement in the trench
– the compactor is used for periods of no more than 4 x 15 minutes per shift, interrupted by breaks
(each approx. 1 hour)
If these boundary conditions are not complied with, the owner is required to implement the protective
measures identied as necessary to avoid CO poisoning as part of the owner’s risk assessment, for
example:
– use of zero-emission compacting equipment
– blower-supported ventilation with a fan forcing air along the length of trench
The use of respiratory equipment during operation of this gasoline-powered compactor without docu-
mented evidence of conformity and without the necessary precautions is generally not permitted!
– as CO will accumulate in the blood after repeated use
– as CO lters have a short service life
Operation
Prior to starting work the owner of the compactor must be familiar with the work environment. The
work environment includes obstacles in the work and trafc area, the bearing capacity of the ground,
as well as the necessary safeguarding of the construction site in the area adjacent to public trafc;
and it includes compliance with trafc regulations.
The soil compactor should only be operated when the protective xtures are mounted. The protective
xtures must all be in functional condition.
At least once per shift the compactor must be checked for apparent defects. If there are apparent
defects then operation of the compactor must be stopped immediately, and the responsible person
must be informed. Prior to restarting, compactor malfunctions that have occurred must be corrected.
Always maintain adequate clearance to the edges of pits and embankments.
Do not drive at ninety degrees to slopes to prevent the compactor from tipping over.
After work has been concluded secure the compactor in accordance with statutory regulations,
particularly in the area of public trafc surfaces.
Operation under difcult conditions
Never inhale the exhaust gas. It contains carbon monoxide, a colorless and odorless gas that
is extremely hazardous, which, if inhaled even briey, can cause unconsciousness and death.
Therefore, never operate the engines in enclosed areas or in areas that are poorly ventilated
(tunnels, caves, covered pits, etc.).
Exercise particular caution when operating the engine in the vicinity of people and livestock.

CF 2-II Hd 7
Maintenance and repair work
Only use original Weber MT spare parts to ensure reliable and safe operation for maintenance
or repair work.
Hydraulic hose lines must be checked at regular intervals in accordance with standard engineering
practice, or they must be replaced at appropriate intervals, even if no signs of safety-relevant defects
are present.
Adjusting tasks, maintenance tasks, and inspection tasks must be carried out on schedule as
specied in this operating and maintenance manual. These activities should only be executed by
instructed personnel.
For repair, service, or inspection work the engine of the compactor must be safeguarded against
unintentional starting.
All pressurized lines, particularly hydraulic lines and lines of the injection system of the drive motor
must be depressurized before performing maintenance or repair tasks.
For maintenance and repair tasks the compactor must be parked on a level and stable substrate
and must be secured from rolling off or tipping over.
Heavy components and assemblies must be secured to and lifted by hoisting machines that can
bear their weight when they are replaced. Ensure that no hazard is caused by raising components
or assemblies.
Do not position yourself or work under suspended loads.
If lubricating oils and fuel come into contact with skin, they can cause skin cancer. Upon contact
with the skin, clean affected skin with suitable cleaning agent without delay.

8 CF 2-II Hd
Inspection
Compactors must be inspected in accordance with the corresponding implementation conditions
and operating conditions, as needed; however an inspection to ensure operationally safe status
must be performed by an expert at least once a year. The results of the inspection must be recorded
in writing and must be stored at least until the next inspection.
Cleaning work
Prior to cleaning the compactor with a high-pressure cleaner, protect all accessible energized
switches, cable connections, etc. against water penetration by masking them off.
Cleaning tasks should only be executed in areas that are suitable and have been approved for this
purpose (oil separator amongst others).
Disposal
All operating uids and auxiliary materials must be disposed of in an environmentally compatible
manner in accordance with country-specic regulations.
Important information for operating and maintenance personnel is marked by pictograms.
Warning against irritants or materials hazardous to health
Warning against a hazardous place
Warning against a suspended load
Wear ear protection
General regulation
Environmental protection
Hard hat
Safety shoes
Protective gloves

CF 2-II Hd 9
2
4
3
1
5
6
Graphic presentation
Overall view – CF 2-II Hd
1 Engine
2 Guide bar
3 Engine bracket
4 Base plate
5 Gas lever
6 Exciter
7 Water tank (not shown) (Accessory)
8 Undercarriage (not shown) (Accessory)
9 Protective mat (not shown) (Accessory)
10 Hearing protection (sticker)

10 CF 2-II Hd
Device description
The CF 2-II Hd soil compactor is used for road-building and landscaping compaction tasks.
Drive
The unit is powered by an air-cooled Honda gasoline engine.
Force is transferred to the exciter mechanically via a V-belt.
Operation
Start the Honda gasoline engine with the attached reversing starter. After starting, vibration is switched
on via the centrifugal clutch attached to the engine.
The guide bar is used to steer the soil compactor.

CF 2-II Hd 11
Technical data
CF 2-II Hd
Weight
Operating weight CECE in kg 83
Dimensions
Overall length (in mm) 1130
Overall width (in mm) 450
Height with folded guide bar (in mm) 960
Base plate length (base in mm) 400
Pressure surface (in mm) 400x450
Drive
Engine manufacturer Honda
Type GX 160
Performance at operating speed
in accordance with ISO 3046-1 (kW) 2.7
Combustion process 4-stroke gasoline
Operating speed (1/min) 3000
Drive speed forward
(soil-dependent in m/min) 26
Incline capacity (ground-dependent in %) 35
Area capacity (in m²/h) 702
Vibration
System Single shaft vibrator
Drive concept Mechanical
Frequency (in Hz) 95
Centrifugal force (in kN) 15
CF 2-II Hd
Noise emissions in accordance with 2000/14/EC
91
105
Sound pressure level LPA
ascertained in accordance with EN 500, in dB (A)
Sound power level LWA
ascertained in accordance with EN ISO 3744
and EN 500, in dB (A)
Vibration values
2.4
Root-mean-square acceleration value for
hand-arm vibration ascertained in accordance
with EN 500 in m/s²
In accordance with directive 2006/42/EC,
complying with the vibration values is the
owner’s responsibility.

12 CF 2-II Hd
2
1
3 4
56
1 Description 2 TYPE
.............................................................. ..............................................................
3 Serial number 4 Year of construction
.............................................................. ..............................................................
5 Mass 6 Rated power kW
.............................................................. ..............................................................

CF 2-II Hd 13
1
2
3
4
5
6
Activities prior to starting work
When transporting the soil compactor on a vehicle,
secure it with suitable restraints.
Transport
Fit the crane hook into the lifting ring (1) and lift the machine
onto the desired means of transport.
Only use lifting machines with a minimum bearing
capacity of 150 kg.
Do not step under suspended loads.
Mounting the undercarriage
Arrest the guide bar (2) with the spring bolt (3).
Use the screws (5) to fasten the undercarriage (4) to the
engine console (6).
The manual guidance rod must be locked during trans-
port.
Pivot the undercarriage under the base plate.

14 CF 2-II Hd
2
3
1
5
4
Mounting the water sprinkling system
Lift the water tank (1) into the frame (2).
Completely empty the water tank if there might be a frost.
Attach the water spray pipe (3) to the base plate.
Check the engine oil level
Unscrew and pull the oil dipstick (4) out of the crankcase.
Insert the oil dip stick in the oil ller neck, but do not
screw it in.
The correct oil level is between the min. and max. marks.
When reaching the min. mark engine operation must be
stopped immediately, and the oil level must be topped
up to the max. mark.
Risk of engine damage if the oil level drops below the
minimum oil level in unfavorable operating conditions.
Max.
Min.
UPPER LEVEL
LOWER LEVEL
Check the fuel level
For work at the fuel system, have a suitable re-extin-
guishing agent at the ready.
Fire, naked light, and smoking is forbidden!
Open the gas cap (5) and, if necessary, top off with fuel as
specied.

CF 2-II Hd 15
1
2
4
5
67
3
Installing the protective mat
Hook in the protective mat at the rear.
Fasten with holder, screws, spring-lock washers and nuts (1)
on the base plate front.
Ensure that the protective mat rests under the base plate.
Starting
Turn the short-circuit button (2) to the “ON” position.
Bring the gas lever (3) into full-throttle position.
Slide the choke lever (4) to the left (close).
Open the fuel cock (5).
Slowly tighten the handle (6) of the reversing starter (7) until
resistance is noticeable.
Allow the handle (6) to glide back into the initial position, and
then forcefully and completely pull it through with both hands.
After the engine has warmed up, slide the choke lever to
the right (open).

16 CF 2-II Hd
2
1
4
5
3
Compacting
Bring the gas lever (1) into full-throttle position.
Control drive speed and direction of travel with the handle (2).
Only run machine within reach of the guide bar.
Shutting down
Bring the gas lever (3) into idle position.
Close the fuel cock (4).
Turn the short-circuit button (5) to the “0” – OFF position.
During breaks – even if they are short – the machine
must be shut down.
Parked devices that represent an obstacle must be
safeguarded against through conspicuous measures.

CF 2-II Hd 17
Maintenance overview
Maintenance interval Maintenance point Maintenance activity
After the rst
25 operating hours
Engine – Change the engine oil
– Check valve play, adjust
if necessary
– Re-tighten all accessible
threaded connections
Machine cpl.
Every 8 operating
hours / daily
Air lter – Clean air lter insert,
check for damage,
replace if necessary
Every 150 operating
hours / every 6 months
Engine – Change the engine oil
Every 150 operating
hours / every year
Vibrator
Engine
– Change oil
– Adjust valve play
– Clean spark plug /
adjust electrode gap
The regulations of the engine manufacturer must be complied with in addition to the above
maintenance overview!
Work must be carried out using regulation tools, and the operating and maintenance manual must
be complied with for all work.
All maintenance work: Select collection vessels large enough to prevent oil from spilling onto the
ground. Dispose of waste oil in an environmentally friendly manner (regulation on waste oils).
Dispose of oils, greases, cloths soaked in oil, and replaced parts with oil on them in an environ-
mentally friendly manner.
If lubricating oils and fuel come into contact with skin, they can cause skin cancer. Upon contact
with the skin, clean affected skin with suitable cleaning agent without delay.
If accessible during maintenance, check the condition and stability of all screws.

18 CF 2-II Hd
1
2
3
4
Maintenance work
Change the engine oil
Remove the oil dip stick (1).
Remove the oil drain screw (2) and drain oil.
Only drain engine oil when at operating temperature.
When working in the area of the engine compartment
there is a danger of being burnt!
Risk of scalding due to hot oil.
If lubricating oils and fuel come into contact with skin, they
can cause skin cancer. Upon contact with the skin, clean
affected skin with suitable cleaning agent without delay.
Dispose of oils, greases, cloths soaked in oil, and
replaced parts with oil on them in an environmentally
friendly manner.
Clean / change air lter cartridge
Unscrew the air lter cover (3).
Remove the air lter insert (4) from the air lter enclosure.
Clean air lter insert as specied by the engine manufacturer
if there is damage or if it is extremely dirty.
After emptying completely, put in the oil drain plug /locking
screw (2). Top up oil as specied.

CF 2-II Hd 19
2
4
3
1
Changing the oil in the exciter
Remove the oil drain plug / ller plug (1) and drain oil.
Fill with oil as specied in the ll quantity table.
Screw in oil drain plug or ller plug.
Ensure that the contact surfaces on the oil drain plug/
ller plug and vibrator housing are clean.
Select collection vessels large enough to prevent oil from
spilling onto the ground. Dispose of waste oil in an envi-
ronmentally friendly manner (regulation on waste oils).
Wipe up/off oil slick and oil residue and dispose of
fuel-soaked cleaning cloths in an environmentally re-
sponsible manner.
Checking the V-belt
Remove the V-belt guard (2).
To do this unscrew the screws (3).
Check the V-belt (4) for cracks, damaged anks, and wear.
If there is excessive wear, replace the V-belt.

20 CF 2-II Hd
Operating uids and ll levels
Assembly Operating material
Quality
Quantity
CF 2-II Hd
Engine
Engine oil
SAE 10 W 40
(– 10 ~ +50 °C)
API – CD CE
or SHPD
or CCMC – D2 – D3 – PD1
0.6 l
Fuel tank
Gasoline Unleaded gasoline 3.1 l
Vibrator Engine oil 10 W 40/15 W 40 0.2 l
Troubleshooting
Fault Possible cause Remedy
Soil compactor
does not start
Operating error
Lack of fuel
Fuel lter fouled
Air lter fouled
Execute start process
as prescribed
Check the fuel level
Change the fuel lter
Clean / change air lter
cartridge
No vibration /
no forward motion
or insufcient
forward motion
Vibrator V-belt defective Change vibrator V-belt