Ross IAFLAT-RO User manual

Digital Indoor Aerial - Flat Panel 4G
IAFLAT-RO
User Manual
Please read this manual thoroughly before using your Ross Indoor Aerial and then retain for future reference
1.1 Important Safety Instructions:
• Please read these instructions carefully and retain for future reference. If you sell, or give this aerial
away be sure to pass on the instructions.
• There are no user serviceable parts inside this unit. DO NOT open there are dangerous voltages
inside. Electric shock hazard.
• This unit operates on AC 230V ~50Hz DC12V/50mA supply.
• During use, this device may become warm, this is normal. DO NOT allow anything to block the
ventilation slots as this may cause overheating and a consequent risk of re.
• To be completely disconnected from the power input the power adaptor must be disconnected
from the mains.
• The marking plate is located on the bottom enclosure of the apparatus.
• DO NOT use the aerial during a thunderous day and turn o the power
• DO NOT place naked ames (such as candles) on this equipment.
• DO NOT stand other equipment on this unit.
• DO NOT obstruct the power adaptor and it should remain easily accessible during use.
• DO NOT operate close to heaters or other heat sources.
• DO NOT stand on soft furnishings
• DO NOT allow anything to trap, pinch or otherwise damage the power cord, if the power cord
should become damaged IMMEDIATELY switch the aerial o at the wall and unplug it, you should
then contact your service centre to carry out a repair.
• DO NOT overload the wall socket, this can be dangerous and lead to a re hazard.
• MAKE SURE you have easy access to the mains plug in case of emergency.
• DO NOT unplug the unit by pulling the power cord, always grasp the plug rmly and pull from
the wall socket.
• DO NOT touch the mains plug or power cord with wet hands. Electric shock hazard.
• DO NOT stand items such as water lled cases on the aerial.
• DO NOT operate this unit in damp conditions or allow water or other uids to enter the enclosure. If
this happens, switch o IMMEDIATELY and refer the device to the Ross helpline.
• DO NOT connect or disconnect cables from the aerial when it is turned on. Switch o the
power unit rst.
• DO NOT clean this device using solvent based products. Use only a soft dry cloth.
For TVs with built-in tuner (Digital Signals)
(A) Powered via built-in tuner (B) Powered via AC/DC adaptor
(A) Plug the antenna coaxial cable to the external
amplier and plug the ampliers coaxial cable
to the RF jack of your TV.
(B) Plug the antennas coaxial cable to the ANT
jack of the external amplier and plug the
ampliers coaxial cable to the RF jack of your
TV. Plug the power adaptors DC plug to the
DC jack of the external amplier and the
power plug to the electrical outlet.
Option 2:
For Strong signal areas (without amplier)
Conguration (A) Connection to the digital receiver:
Plug the antenna coaxial cable to the ANT jack of your digital receiver
Conguration (B) Connection to the
TV with built in digital tuner:
Plug the antennas coaxial cable to the RF jack of your TV
Additional notes and tips
• If you are having major reception issues you might want to try placing the antenna
in a dierent position. (For example near a window)
• You can use the antenna with or without its amplier, depending on which connection
gives you the best signal. Using the amplier provides the best performance in most
situations, so try using it rst. If you notice that you have lost channels that you
normally receive, try connecting without the amplier
Technical Support UK: 0845 194 7584 • Email: [email protected]o.uk

4.0 Product Features
Please nd details of the Ross Digital Indoor Aerial – Flat panel 4G features below:
• Built-in LTE/4G lters to avoid interference from 4G mobile phone signals
• Receives full HD television, digital signals and DAB radio programs: for reception of local and
regional UHF and VHF signals as well as FM radio signals
• Signal clear technology with extremely low noise circuitry
• Wide band amplier for best picture and sound quality
• Includes external amplier to enhance performance in poor reception areas
• Can be as active or passive version, depending on signal strength received
• Can be powered by digital receiver (5V/30mA) via aerial (coax) cable
• Can be powered by AC/DC power adaptor (Included)
• Power-on indicator light with on/o switch for energy saving
• Auto gain control
• Attractive “piano” Black nish
• Ultra slim design
5.0 Installation
There are various installation congurations which can be used on the Ross Digital Indoor
Aerial - Flat Panel these are determined by the digital signal strength received in your area
http://www.digitaluk.co.uk/coveragechecker/
Option 1:
For weak signal areas including the amplier
Conguration (A) Powered via Digital receiver:
Plug the antennas coaxial cable to the ANT jack of
the external amplier and plug the ampliers coaxial
cable into the ANT jack of your digital receiver, this will
get 5V/30mA power from the digital receiver.
Conguration (B) Powered via AC.DC adaptor:
With digital receiver to receiver signals
Plug the antennas coaxial cable to the ANT jack of
the external amplier and plug the ampliers coaxial
cable to the ANT jack of your digital receiver. Plug the
power adaptors DC plug into the DC jack of the
external amplier and the power plug to the
electrical outlet.
1.2 General Information
• Thank you for choosing the Ross Digital Indoor Aerial – Flat panel 4G. Treated with care and used
in accordance with the contents of this manual it will provide many years of reliable service
• This symbol indicates that, at the end of its useful life, this product must not be
disposed of with normal domestic waste. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, please recycle it responsibly.
• This product conforms to all applicable EU legislation for this type of product. Further
information can be obtained from Ross if required.
• Please note in order to receive digital TV signals you will require a digital box of some
description
2.0 In the Box:
Please open your box carefully and check the contents which should be as the list below: If
anything is missing please contact the Ross helpline or return the product to the point of
purchase.
• Digital Indoor Flat Aerial
• DC Power adaptor
• AC Adaptor
• User manual
3.0 Product Specications
Please nd the detailed specications for Ross Digital Indoor Aerial – Flat panel 4G below:
• Reception Channels: 5-12, 21-69
• Frequency: VHF: 174-230MHz UHF: 470-790MHz
• Max Noise Figure: 1.4/1.7dB (VHF/UHF)
• VSWR (Voltage Standing Wave Ratio) <2.5
• Max Output Level: 84dBµV
• 3dB Beam Width: ±22˚/ ±20˚ (VHF/UHF)
• Input Voltage: AC 230V ~ 240V
• Working Voltage: DC6V/50mA
• Impedance (Ω): 75
• Connector: IEC-Connector